例185.如图8-1所示,轮板零件的加工,毛坯用压板固定在机床工作台面上,材料为铝合 金,要求加工外轮廓和内孔,加工深度5mm(粗加工) ‰0176 N10 G55 LF N20 T01 DO1 MO6 LF N30G90S1000M03LF N40 G00 Z50 LF N50 G41 T1 D1 GO0 XO Y27. 5 Z2 LF N60 G01 Z-5 F100 LF N70G03X14.18Y34.0610J20LF N80G02X22.09Y29.8413.19J-2.89LF N90G03X36.92Y4.2I19.05J-6.09LF N100G02X36.92Y-4.21-0.92J-4.2LF N110G03X22.09￥-29.8414.22J-19.55LF N120G02X14.81Y-34.061-4.09J1.33LF N130G03X-14.81Y34.061-14.81J-13.44LF N140G02X-22.09￥-29.841-3.19J2.89LF N150G03X-36.92￥-4.2I19.05J6.09LF N160G02X-36.92Y4.210.92J4.2LF N170G03-22.09Y29.841-4.22J19.55LF N180G02X-14.81Y29.8414.09J19.55LF N190G03X0Y27.5I14.81J13.44LF N200G00Z100LF N210 MO5 LF N220 G40 GO1 XO YO LF N230 T02 MO6 LF N240G90G94G56M6T2S1200M03LF N250G00 Yo Z50 LF GO1 Z-2 F80 LF N280 GO0 Z2 LF N290X-10Y-17.32LF N300G012-2LF N310 G00 Z2 LF例 185.如图 8-1 所示，轮板零件的加工，毛坯用压板固定在机床工作台面上，材料为铝合 金，要求加工外轮廓和内孔，加工深度 5mm（粗加工）。 %0176 N10 G55 LF N20 T01 D01 M06 LF N30 G90 S1000 M03 LF N40 G00 Z50 LF N50 G41 T1 D1 G00 X0 Y27.5 Z2 LF N60 G01 Z-5 F100 LF N70 G03 X14.18 Y34.06 I0 J20 LF N80 G02 X22.09 Y29.84 I3.19 J-2.89 LF N90 G03 X36.92 Y4.2 I19.05 J-6.09 LF N100 G02 X36.92 Y-4.2 I-0.92 J-4.2 LF N110 G03 X22.09 Y-29.84 I4.22 J-19.55 LF N120 G02 X14.81 Y-34.06 I-4.09 J1.33 LF N130 G03 X-14.81 Y34.06 I-14.81 J-13.44 LF N140 G02 X-22.09 Y-29.84 I-3.19 J2.89 LF N150 G03 X-36.92 Y-4.2 I19.05 J6.09 LF N160 G02 X-36.92 Y4.2 I0.92 J4.2 LF N170 G03 -22.09 Y29.84 I-4.22 J19.55 LF N180 G02 X-14.81 Y29.84 I4.09 J19.55 LF N190 G03 X0 Y27.5 I14.81 J13.44 LF N200 G00 Z100 LF N210 M05 LF N220 G40 G01 X0 Y0 LF N230 T02 M06 LF N240 G90 G94 G56 M6 T2 S1200 M03 LF N250 G00 X20 Y0 Z50 LF N260 Z2 LF N270 G01 Z-2 F80 LF N280 G00 Z2 LF N290 X-10 Y-17.32 LF N300 G01 Z-2 LF N310 G00 Z2 LF