Chapter 1 Mold Order and solution 1.1 Request for Mold Quotation Table 1-1: request for mold quotation from a customer Request for Mold Quotation PART NAME NO CAV. RFQ DATE DRAWING NUMBER REVISION QUOTE DUE DATE MATERIAL TYPE SHRINK RATE STANDARD FEATURES SPECIAL FEATURES IX Locating ring nm diameter IX]Sprue bushing mm radius [X Guided ejector system [X Balanced Lift Hole in Mold Strap [X Early ejector return [X Cycle Counter [X Lift holes on All Mold Plates IX Parting line locks X Pry slots"NO Corners TX Cavity I.D. on molded part(for multi-cavity) TX Unscrewing cores IX Recessed cooling connectors 1/4"NPT(P-252) TX Center Ko is NOT used in our shop [X Engrave Part number and Mold Number MOLD DESIGN MOLD CONSTRUCTION X Mold maker Ⅺ Customer TX Standard 2 plate X Hot Sprue Bushing KX Full detai T Lay-out only [X Two Shot Mold [X Hot Runner TXMUD Inserts EJECTION GATETYPE RUNNER MOLD BASE MATERIAL IX Knock Out Pins X Full Round [X] Stripper Plate IX Ejector Blade TX] Sprue [ X Runner Shut-offs [XAir Assist [X Pin Point SIDE ACTION COOLING CAVITY [X Mechanical Slides [INserts [X Hardened Tool Steel TX Hardened Tool Steel [X Wear Plates(Lamina) K Retainer Plates [X Hardened Stainless []Hardened Stainless [X] Positive Locks(Superior)[]Support Plate XIPre-Hardened Steel [X Pre-Hardened Steel [X Hydraulic Cylinder TX Bubblers TXJ Air Cylinder Ⅺ] Finish TXFinChapter 1 Mold Order and Solution 1.1 Request for Mold Quotation ` Table 1-1: request for mold quotation from a customer 1. Request for Mold Quotation PART NAME NO. CAV. RFQ DATE DRAWING NUMBER REVISION QUOTE DUE DATE MATERIAL TYPE SHRINK RATE . STANDARD FEATURES SPECIAL FEATURES [X] Locating ring: mm diameter [X]Sprue bushing mm radius [X] Guided ejector system [X] Balanced Lift Hole in Mold Strap [X] Early ejector return [X] Cycle Counter [X] Lift holes on All Mold Plates [X] Parting line locks [X] Pry slots “NO Corners” [X] Cavity I.D. on molded part (for multi-cavity) [X] Unscrewing cores [X] Recessed cooling connectors 1/4" NPT (JP-252) [X] Center KO is NOT used in our shop [X] Engrave Part number and Mold Number MOLD DESIGN MOLD CONSTRUCTION Design by: [X] Mold maker [X] Customer [X] Standard 2 plate [X] Hot Sprue Bushing Type of design: [X] Full detail [X] Lay-out only [X] 3 plate [X] Two Shot Mold [X] Hot Runner [X] M.U.D. Inserts EJECTION GATE TYPE RUNNER MOLD BASE MATERIAL [X] Knock Out Pins [X] Sub-gate [X] Trapezoid [X] Sleeves [X] Edge Gate [X] Full Round [X] Stripper Plate [X] Hot Bushing [X] Hot Manifold [X] Ejector Blade [X] Sprue [X] Runner Shut-offs [X] Air Assist [X] Pin Point SIDE ACTION COOLING CORE CAVITY [X] Mechanical Slides [X] Inserts [X] Hardened Tool Steel [X] Hardened Tool Steel [X] Wear Plates (Lamina) [X] Retainer Plates [X] Hardened Stainless [X] Hardened Stainless [X] Positive Locks (Superior) [X] Support Plate [X] Pre-Hardened Steel [X] Pre-Hardened Steel [X] Hydraulic Cylinder [X] Bubblers [X] [X] [X] Air Cylinder [X] Slides [X] Finish [X] Finish