GeoCOM Reference Manual l0.3.6 GetSWVersion-Get Software version l0-7 10.3.7 CSI GetvBat-Get the value of the voltage supply 10.3.8 CSV GetVMem-Get value of the memory backup voltage supply.. 10-9 10.3.9 CSV GetInt Temp-Get the temperature l0-10 CONTROLLER TASK-CTL 11-1 11.1 FUNCtIONs 71.1.I CTL GetUpCounter-Get Up Counter. l-1 12 ELECTRONIC DISTANCE MEASUREMENT- EDM 121 USAGE 12-1 12.2 CONSTANTS AND TYPES 12-1 12.3 FUNCTIONS 12.3.3 EDM SetEglIntensity-Change intensity of guide ligt.12-2 12.3.1 EDM Laserpoinmter-Switch on/off laserpointer 12.3.2 EDM GetEglIntensity-Get value of intensity of guide lig 12-4 12. 13 MOTORISATION- MOT 13-1 13.1 13-1 13.2 CONSTANTS AND TYPES 13.3 FUNCTIONS 13-2 13.3.1 MOT ReadLockStatus-Return condition of LockIn control....13-2 13.3.2 MOT Start Controller- Start motor controller l3-3 13.3.3 MOT StopController-Stop motor controller. 13-4 13. 3.4 MOT Set velocity- Drive Instrument with visual control 14 SUPERVISOR-SUP 14.1 CONSTANTS AND TYPES 142 FuNCtIONS l4-1 14.2.1 SUP GetConfig-Get power management configuration status 14-1 14.2.2 SUP SetConfig-Set power management configuration 14.2.3 SUP SwitchLow Temp Control -Set low temperature control l4-4 15 THEODOLITE MEASUREMENT AND CALCULATION- TMC 15-1 15.1 15-2 15. .I Inclination measurement/correction l5-2 15.1.2 Sensor measurement programs l5-3 15.2 CONSTANTS AND TYPES 15.3 MEASUREMENT FUNCTIONS 15-7 15.3.1 TMC GetCoordinate-Gets the coordinates of a measured point..15-7 15.3.2 TMC GetSimpleMea- Returns angle and distance measurement.. 15-10 TPSI100-Version lo1GeoCOM Reference Manual Contents TPS1100-Version 1.01 IV 10.3.6 CSV_GetSWVersion - Get Software Version.......................................... 10-7 10.3.7 CSV_GetVBat - Get the value of the voltage supply.............................. 10-8 10.3.8 CSV_GetVMem - Get value of the memory backup voltage supply ...... 10-9 10.3.9 CSV_GetIntTemp - Get the temperature............................................... 10-10 11 CONTROLLER TASK – CTL............................................................... 11-1 11.1 FUNCTIONS ................................................................................................ 11-1 11.1.1 CTL_GetUpCounter – Get Up Counter.................................................. 11-1 12 ELECTRONIC DISTANCE MEASUREMENT - EDM.................... 12-1 12.1 USAGE........................................................................................................ 12-1 12.2 CONSTANTS AND TYPES............................................................................ 12-1 12.3 FUNCTIONS ................................................................................................ 12-2 12.3.1 EDM_Laserpointer - Switch on/off laserpointer.................................... 12-2 12.3.2 EDM_GetEglIntensity - Get value of intensity of guide light................ 12-4 12.3.3 EDM_ SetEglIntensity - Change intensity of guide light....................... 12-5 13 MOTORISATION - MOT....................................................................... 13-1 13.1 USAGE........................................................................................................ 13-1 13.2 CONSTANTS AND TYPES............................................................................ 13-1 13.3 FUNCTIONS ................................................................................................ 13-2 13.3.1 MOT_ReadLockStatus - Return condition of LockIn control................ 13-2 13.3.2 MOT_StartController - Start motor controller...................................... 13-3 13.3.3 MOT_StopController - Stop motor controller........................................ 13-4 13.3.4 MOT_SetVelocity - Drive Instrument with visual control..................... 13-5 14 SUPERVISOR - SUP ............................................................................... 14-1 14.1 CONSTANTS AND TYPES............................................................................ 14-1 14.2 FUNCTIONS ................................................................................................ 14-1 14.2.1 SUP_GetConfig - Get power management configuration status.......... 14-1 14.2.2 SUP_SetConfig - Set power management configuration....................... 14-3 14.2.3 SUP_SwitchLowTempControl - Set low temperature control............... 14-4 15 THEODOLITE MEASUREMENT AND CALCULATION - TMC 15-1 15.1 USAGE........................................................................................................ 15-2 15.1.1 Inclination measurement/correction....................................................... 15-2 15.1.2 Sensor measurement programs............................................................... 15-3 15.2 CONSTANTS AND TYPES............................................................................ 15-3 15.3 MEASUREMENT FUNCTIONS...................................................................... 15-7 15.3.1 TMC_GetCoordinate – Gets the coordinates of a measured point....... 15-7 15.3.2 TMC_GetSimpleMea - Returns angle and distance measurement...... 15-10