cL7106,cL7107,cL7106s,|cL7107S Absolute Maximum Ratings Thermal Information Supply Voltage Thermal Resistance(Typical, Note 2) 0JA CCM) ICL7106. V+ to v- PDIP Package ICL7107. V+ to GND 6 ICL7107.V-to GND -9v Maximum Junction Temperature Analog Input voltage(Either Input)(Note 1) V+ to V- Maximum Storage Temperature Range -65°cto150° Reference Input Voltage(Either Input) V+ to V- Maximum Lead Temperature(Soldering 10s) Clock Input MQFP-Lead Tips Only CL7106 TEST to V+ ICL71 Operating Conditions Temperature Range 0cto7o°c CAUTION: Stresses above those listed in Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation the device at these or any other conditions above those indicated in the operational sections of this specification is not implied NOTES: ut current Is 2. BJA is measured with the component mounted on an evaluation PC board in free air Electrical Specifications ( Note 3) PARAMETER TEST CONDITIONS TYP MAX UNIT SYSTEM PERFORMANCE Zero Input Reading VIN=0.0V, Full Scale= 200mV 0000±0000+0000 Digital Stability(Last Digit)(ICL7106S, ICL7107s Fixed Input Voltage( Note 7) 000d0000000gita Ratiometric Reading VIN= VREF, VREF =100mV 999999/101000 Rollover Errol Difference in Reading for Equal Positive and Negative Inputs Near Full Scale Linearity Full scale 200mv or Full scale 2V Maximum ±0.2 Counts Deviation from Best Straight Line Fit(Note 6) Common Mode Rejection Ratio CM=1V, VIN=OV, Full Scale 200mV(Note 6) ViN=oV, Full Scale= 200mV 15 ( Peak-To-Peak value Not Exceeded 95% of Time) Leakage] Input VIN =0(Note 6) 10 pA Zero Reading Drift VN=0,0°cTo70°c(Note6) Scale Factor Temperature Coefficient VN=199mV,0°cTo70°c, ppmn°c ( Ext. Ref0ppm/°C) End Power Supply Character V+ Supply VIN=O(Does Not Indlude LED Current for ICL7107) 1.0 18 mA Current End Power Supply Character V Supply Current ICL7107 Only 0618 COMMON Pin Analog Common Voltage Temperature Coefficient of Analog Common 25kQ2 Between DISPLAY DRIVER ICL7106 ONLY Peak-To-Peak Segment Drive Voltage V+= to v-= 9v(Note 5) 5.5 Peak-To-Peak Backplane Drive Voltage3 Absolute Maximum Ratings Thermal Information Supply Voltage ICL7106, V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V ICL7107, V+ to GND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V ICL7107, V- to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-9V Analog Input Voltage (Either Input) (Note 1). . . . . . . . . . . . . V+ to V￾Reference Input Voltage (Either Input) . . . . . . . . . . . . . . . . . V+ to V￾Clock Input ICL7106 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TEST to V+ ICL7107 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .GND to V+ Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to 70oC Thermal Resistance (Typical, Note 2) θJA (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 MQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (MQFP - Lead Tips Only) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Input voltages may exceed the supply voltages provided the input current is limited to ±100µA. 2. θJA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications (Note 3) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT SYSTEM PERFORMANCE Zero Input Reading VIN = 0.0V, Full Scale = 200mV -000.0 ±000.0 +000.0 Digital Reading Stability (Last Digit) (ICL7106S, ICL7107S Only) Fixed Input Voltage (Note 7) -000.0 ±000.0 +000.0 Digital Reading Ratiometric Reading VlN = VREF, VREF = 100mV 999 999/10 00 1000 Digital Reading Rollover Error -VIN = +VlN ≅ 200mV Difference in Reading for Equal Positive and Negative Inputs Near Full Scale - ±0.2 ±1 Counts Linearity Full Scale = 200mV or Full Scale = 2V Maximum Deviation from Best Straight Line Fit (Note 6) - ±0.2 ±1 Counts Common Mode Rejection Ratio VCM = 1V, VIN = 0V, Full Scale = 200mV (Note 6) - 50 - µV/V Noise VIN = 0V, Full Scale = 200mV (Peak-To-Peak Value Not Exceeded 95% of Time) - 15 - µV Leakage Current Input VlN = 0 (Note 6) - 1 10 pA Zero Reading Drift VlN = 0, 0oC To 70oC (Note 6) - 0.2 1 µV/oC Scale Factor Temperature Coefficient VIN = 199mV, 0oC To 70oC, (Ext. Ref. 0ppm/oC) (Note 6) - 1 5 ppm/oC End Power Supply Character V+ Supply Current VIN = 0 (Does Not Include LED Current for ICL7107) - 1.0 1.8 mA End Power Supply Character V- Supply Current ICL7107 Only - 0.6 1.8 mA COMMON Pin Analog Common Voltage 25kΩ Between Common and Positive Supply (With Respect to + Supply) 2.4 3.0 3.2 V Temperature Coefficient of Analog Common 25kΩ Between Common and Positive Supply (With Respect to + Supply) - 80 - ppm/oC DISPLAY DRIVER ICL7106 ONLY Peak-To-Peak Segment Drive Voltage Peak-To-Peak Backplane Drive Voltage V+ = to V- = 9V (Note 5) 4 5.5 6 V ICL7106, ICL7107, ICL7106S, ICL7107S