Ron Suiter, BSEE Lehigh, MBA USC Ron began his career as an aircraft system designer in Douglas Aircraft Company's Hydro-Mechanical system design group. He became Unit Chief of the braking system design

Multidisciplinary System An mdo value framework Design Optimization(MSDO) Lifecycle cost models Design for Value Value metrics valuation techniques ecture 24 Value-based mdo

礼服的概念、风格及分类 礼服的造型 礼服的色彩 礼服的材料 礼服的做工 现代礼服的设计变化

1. Automatic Control System 1.1 Introduction 1.2 An example 1.3 Types of control system 2. Mathematical Foundation 2.1 The transfer function concept 2.2 The block diagram. 2.3 Signal flow graphs 2.4 Construction of signal flow graphs 2.5 General input-output gain transfer 3. Time-Domain Analysis Of Control System 3.1 Introduction 3.2 Typical test signals for time response of control systems 3.3 First –Order Systems 3.4 Performance of a Second-Order System 3.5 Concept of Stability 4. The Root Locus Techniques 4.1 Introduction 4.2 Root Locus Concept 4.3 The Root Locus Construction Procedure for General System 4.4 The zero-angle (negative) root locus 5. Frequency-Domain Analysis of Control System 5.1 Frequency Response 5.2 Bode Diagrams 5.3 Bode Stability Criteria 5.4 The Nyquist Stability Criterion 6. Control system design 6.1 Introduction 6.2 Cascade Lead Compensation 6.3 Properties of the Cascade Lead Compensator 6.4 Parameter Design by the Root Locus Method

System compensation is the process of designing a controller that will produce an acceptable transient response while maintaining a desired steady-state accuracy .These two design objectives are conflicting in most systems ,since small errors imply high gains reduce system stability and may even drive the system unstable .Compensation may be thought of as the process of increasing the stability of a system without reducing its accuracy below minimum acceptable standards

System compensation is the process of designing a controller that will produce an acceptable transient response while maintaining a desired steady-state accuracy .These two design objectives are conflicting in most systems ,since small errors imply high gains reduce system stability and may even drive the system unstable .Compensation may be thought of as the process of increasing the stability of a system without reducing its accuracy below minimum acceptable standards

1. Automatic Control System 1.1 Introduction 1.2 An example 1.3 Types of control system 2. Mathematical Foundation 2.1 The transfer function concept 2.2 The block diagram. 2.3 Signal flow graphs 2.4 Construction of signal flow graphs 2.5 General input-output gain transfer function 3. Time-Domain Analysis Of Control System 3.1 Introduction 3.2 Typical test signals for time response of control systems 3.3 First –Order Systems 3.4 Performance of a Second-Order System 3.5 Concept of Stability 4. The Root Locus Techniques 4.1 Introduction 4.2 Root Locus Concept 4.3 The Root Locus Construction Procedure for General System 4.4 The zero-angle (negative) root locus 5. Frequency-Domain Analysis of Control System 5.1 Frequency Response 5.2 Bode Diagrams 5.3 Bode Stability Criteria 5.4 The Nyquist Stability Criterion 6. Control system design 6.1 Introduction 6.2 Cascade Lead Compensation 6.3 Properties of the Cascade Lead Compensator 6.4 Parameter Design by the Root Locus Method

第一章、内衣的历史演变 一、中国古代内衣 二、西方内衣的历史 第二章、内衣的设计 第三章、内衣裁剪与规格 一、内衣的立体裁剪 （一）、立体取样 （二）、拓版修正 （三）、试穿 二、内衣的平面原型裁剪 （一）、文胸平面制版 （二）、拓版修正

深圳大学艺术设计学院：《女装设计与工艺 Fashion Design And Technological Design》课程教学资源（PPT课件）02 女装设计与工艺——休闲装设计与结构

鞣制后的动物表皮，柔软、坚韧等性能，鞣制的方式不同出现光面和绒面效果。皮革的使用历史悠久，从涂油脂、烟熏、石灰浸制到铬鞣法。皮革主要有羊皮、牛皮、猪皮、蛇皮、鳄鱼皮等。皮革张幅有限，不同部位质地不同，在设计中多采用拼接和结构分割的手法来弥补。在制作中采用单张皮子裁剪，注重配色、避免皮革表面的伤残、合理节约的使用皮革。皮革服装的加工程序为：设计—纸样—样衣—样板—配皮—裁剪—缝制—熨烫—成衣。裁剪时用专用裁刀，缝纫机也和普通机器的压脚不同----塑料压脚，针距大。皮革的熨烫温度为90度—100度