Partll Solid Waste Engineering 12 Evolution of Solid Waste Management Solid wastes comprise all the wastes arising from human and animal activities that are normally solid and that are discarded as useless or unwanted. The term solid waste as used in this text is all-inclusive encompassing the heterogeneous mass of throwaways from the urban community as well as the more homogeneous accumulation of agricultural, industrial, and mineral wastes. This book is focused on the urban setting, where the accumulation of solid wastes is a direct consequence of life 12.1 Solid Waste-a Consequence of Life From the days of primitive society, humans and animals have used the resources of the earth to support life and to dispose of wastes. In early times, the disposal of human and other wastes did not pose a significant problem, for the population was small and the amount of land available for the assimilation of wastes was large. Although emphasis is currently being placed on recycling the energy and fertilizer values of solid wastes, the farmer in ancient times probably made a bolder attempt at this Indications of recycling may still be seen in the primitive, yet sensible, agricultural practices in many of the developing nations where farmers recycle solid wastes for fuel or fertilizer values Problems with the disposal of wastes can be traced from the time when humans first began to congregate in tribes. villages, and communities and the accumulation of wastes became a consequence of life. Littering of food and other solid wastes in medieval towns-the practice of throwing wastes into the unpaved streets, roadways, and vacant land-led to the breeding of rats, with their attendant fleas carrying bubonic plague. The lack of any plan for the management of solid wastes thus led to the epidemic of plague, the Black Death, that killed half of the fourteenth-century Europeans and caused many subsequent epidemics with high death tolls. It was not until the nineteenth century that public health control measures became a vital consideration to public officials, who began to realize that food wastes had to be collected and disposed of in a sanitary manner to control rodents and flies, the vectors of disease The relationship between public health and the improper storage, collection, and disposal of solid wastes is quite clear. Public health authorities have shown that rats, flies, and other disease vectors breed in open dumps, as well as in poorly constructed or poorly maintained housing, in food storage facilities, and in many other places where food and harborage are available for rats and the insects associated with them cological phenomena such as water and air pollution have also been attributed to improper management of solid wastes. For instance, liquid from dumps and poorly engineered landfills has contaminated surface waters and groundwaters. In mining areas the liquid leached from waste dumps may contain toxic elements, such as copper, arsenic, and uranium, or it may contaminate water supplies with unwanted salts of calcium and magnesium. Although nature has the capacity to dilute, disperse, degrade, absorb, or otherwise reduce the impact of unwanted residues in the atmosphere, in the waterways, and on the land, ecological imbalances have occurred where the natural assimilative capacity has been exceeded 12.2 Waste Generation In a Technological Society The development of a technological society in the United States can be traced to the beginnings of the Industrial Revolution in Europe, unfortunately, so can a major increase in solid waste disposal problems. In fact, in the latter part of the nineteenth century, conditions were so bad in England that an urban sanitary act was passed in 1888 prohibiting the throwing of solid wastes into ditches, rivers, and waters. This preceded by about ll years the enactment of the Rivers and Harbors Act of 1899 in the United States, which was intended to regulate the dumping of debris in navigable waters and adjacent lands Thus, along with the benefits of technology have al so come the problems associated with the dispo of the resultant wastes. To understand the nature of these problems, it will be helpful to
12-1 PartIII Solid Waste Engineering 12 Evolution of Solid Waste Management Solid wastes comprise all the wastes arising from human and animal activities that are normally solid and that are discarded as useless or unwanted. The term solid waste as used in this text is all-inclusive, encompassing the heterogeneous mass of throwaways from the urban community as well as the more homogeneous accumulation of agricultural, industrial, and mineral wastes. This book is focused on the urban setting, where the accumulation of solid wastes is a direct consequence of life. 12.1 Solid Waste—a Consequence of Life From the days of primitive society, humans and animals have used the resources of the earth to support life and to dispose of wastes. In early times, the disposal of human and other wastes did not pose a significant problem, for the population was small and the amount of land available for the assimilation of wastes was large. Although emphasis is currently being placed on recycling the energy and fertilizer values of solid wastes, the farmer in ancient times probably made a bolder attempt at this. Indications of recycling may still be seen in the primitive, yet sensible, agricultural practices in many of the developing nations where farmers recycle solid wastes for fuel or fertilizer values. Problems with the disposal of wastes can be traced from the time when humans first began to congregate in tribes, villages, and communities and the accumulation of wastes became a consequence of life. Littering of food and other solid wastes in medieval towns－the practice of throwing wastes into the unpaved streets, roadways, and vacant land—led to the breeding of rats, with their attendant fleas carrying bubonic plague. The lack of any plan for the management of solid wastes thus led to the epidemic of plague, the Black Death, that killed half of the fourteenth-century Europeans and caused many subsequent epidemics with high death tolls. It was not until the nineteenth century that public health control measures became a vital consideration to public officials, who began to realize that food wastes had to be collected and disposed of in a sanitary manner to control rodents and flies, the vectors of disease. The relationship between public health and the improper storage, collection, and disposal of solid wastes is quite clear. Public health authorities have shown that rats, flies, and other disease vectors breed in open dumps, as well as in poorly constructed or poorly maintained housing, in food storage facilities, and in many other places where food and harborage are available for rats and the insects associated with them. Ecological phenomena such as water and air pollution have also been attributed to improper management of solid wastes. For instance, liquid from dumps and poorly engineered landfills has contaminated surface waters and groundwaters. In mining areas the liquid leached from waste dumps may contain toxic elements, such as copper, arsenic, and uranium, or it may contaminate water supplies with unwanted salts of calcium and magnesium. Although nature has the capacity to dilute, disperse, degrade, absorb, or otherwise reduce the impact of unwanted residues in the atmosphere, in the waterways, and on the land, ecological imbalances have occurred where the natural assimilative capacity has been exceeded. 12.2 Waste Generation In a Technological Society The development of a technological society in the United States can be traced to the beginnings of the Industrial Revolution in Europe; unfortunately, so can a major increase in solid waste disposal problems. In fact, in the latter part of the nineteenth century, conditions were so bad in England that an urban sanitary act was passed in 1888 prohibiting the throwing of solid wastes into ditches, rivers, and waters. This preceded by about 11 years the enactment of the Rivers and Harbors Act of 1899 in the United States, which was intended to regulate the dumping of debris in navigable waters and adjacent lands. Thus, along with the benefits of technology have also come the problems associated with the disposal of the resultant wastes. To understand the nature of these problems, it will be helpful to examine the
flow of materials and the associated generation of wastes in a technological society and to consider the direct impact of technological advances on the design of solid waste facilities Materials flow and waste generation An indication of how and where solid wastes are generated in our technological society is shown in the simplified materials flow diagram presented in Fig 1-1. Solid wastes(debris) are generated at the start of the process, beginning with the mining of raw materials. The debris left from strip-mining operations, for example, is well known to everyone. Thereafter, solid wastes are generated at every step in the process as raw materials are converted to goods for consumption It is apparent from Fig. 12-l that one of the best ways to reduce the amount H Residual debris solid wastes that must be disposed of is to limit the consumption ofraw materials and to increase the rate of Manufactuning Residual waste material recovery and reuse of waste materials effecting this change in a modern Processing and technological society has proved recovery manufacturing extremely difficult. Therefore, society has undertaken improved wa management and searched for new Consumer permanent locations in which to place solid waste. Unlike water-borne and air-dispersed wastes, solid products, and recover Where it materials aste materials where it will be found in the f Fig. 12-1 Materials flow and the generation of solid wastes in a technological society The effects of Technological Advances Modern technological advances in the packaging of goods create a constantly changing set of parameters for the designer of solid waste facilities. Of particular significance are the increasing use of which reduce the quantities of food wastes in the home but increase the quantities at agricultural processing plants. The use of packaged meals, for example, results in almost no wastes in the home except for the packaging materials. These continuing changes present problems to the facilities designer because engineering structures for the processing of solid wastes involves such large capital expenditures that they must be designed to be functional for approximately 25 years. Thus. the engineers responsible for the design of solid waste facilities must be aware of trends, even though they cannot of course. predict all the changes in technology that will affect the characteristics of solid wastes On the other hand, every possible prediction technique must be used in this ever-changing technological society so that flexibility and utility can be designed into the facilities. Ideally, a facility should be functional and efficient over its useful life, which should coincide with the maturity of the bonds that were floated to pay for it. But important questions arise: Which elements of society quantities be minimized? What is the role of resource recovery? Can disposal and recovery technology keep up with consumer product technology? 12.3 The Development of Solid Waste Management iscipline associated with the control of generation. storage. collection transfer and transport. processing, and disposal of solid wastes in a manner that is in accord with the best principles of public health, economics. engineering. conservation, aesthetics. and other environmental considerations. and that is also responsive to public attitudes. In its scope. solid waste management includes all administrative, financial. legal. planning and engineering functions involved in solutions to all problems of solid wastes. The solutions may involve comple
12-2 flow of materials and the associated generation of wastes in a technological society and to consider the direct impact of technological advances on the design of solid waste facilities. Materials Flow and Waste Generation An indication of how and where solid wastes are generated in our technological society is shown in the simplified materials flow diagram presented in Fig. 1-1. Solid wastes (debris) are generated at the start of the process, beginning with the mining of raw materials. The debris left from strip-mining operations, for example, is well known to everyone. Thereafter, solid wastes are generated at every step in the process as raw materials are converted to goods for consumption. It is apparent from Fig. 12-1 that one of the best ways to reduce the amount of solid wastes that must be disposed of is to limit the consumption of raw materials and to increase the rate of recovery and reuse of waste materials. Although the concept is simple, effecting this change in a modern technological society has proved extremely difficult. Therefore, society has undertaken improved waste management and searched for new permanent locations in which to place solid waste. Unlike water-borne and air-dispersed wastes, solid waste will not go away. Where it is thrown is where it will be found in the future. The Effects of Technological Advances Modern technological advances in the packaging of goods create a constantly changing set of parameters for the designer of solid waste facilities. Of particular significance are the increasing use of plastics and the use of frozen foods, which reduce the quantities of food wastes in the home but increase the quantities at agricultural processing plants. The use of packaged meals, for example, results in almost no wastes in the home except for the packaging materials. These continuing changes present problems to the facilities designer because engineering structures for the processing of solid wastes involves such large capital expenditures that they must be designed to be functional for approximately 25 years. Thus, the engineers responsible for the design of solid waste facilities must be aware of trends, even though they cannot, of course, predict all the changes in technology that will affect the characteristics of solid wastes. On the other hand, every possible prediction technique must be used in this ever-changing technological society so that flexibility and utility can be designed into the facilities. Ideally, a facility should be functional and efficient over its useful life, which should coincide with the maturity of the bonds that were floated to pay for it. But important questions arise: Which elements of society generate the greatest quantities of solid waste and what is the nature of these wastes? How can the quantities be minimized? What is the role of resource recovery? Can disposal and recovery technology keep up with consumer product technology? 12.3 The Development of Solid Waste Management Solid waste management may be defined as the discipline associated with the control of generation, storage, collection, transfer and transport, processing, and disposal of solid wastes in a manner that is in accord with the best principles of public health, economics, engineering, conservation, aesthetics, and other environmental considerations, and that is also responsive to public attitudes. In its scope, solid waste management includes all administrative, financial, legal, planning, and engineering functions involved in solutions to all problems of solid wastes. The solutions may involve complex Fig. 12-1 Materials flow and the generation of solid wastes in a technological society
interdisciplinary relationships among such fields as political science, city and regional planning. geography, economics. public health, sociology. demography. communications. and conservation.as Functional Elements of a Waste Management System The problems associated with the management of solid wastes in today's society are complex because of the quantity and diverse nature of the wastes, the development of sprawling urban areas, the funding limitations for public services in many large cities, the impacts of technology, and the emerging limitations in both energy and raw materials. As a consequence, if solid waste management to be accomplished in an efficient and orderly manner, the fundamental aspects and relationships involved must be identified, adjusted for uniformity of data, and understood clearly In this text. the activities associated with the management of solid wastes, from the point of generation to final disposal have been grouped into the six functional elements:(1) waste generation:(2)waste I processI the source:(3) collection: ( 4) separation solid w considering each functional element separately, it is possible(1) to identify the fundamental aspects and relationships involved in each element and(2)to develop, where possible, quantifiable relationships for the purposes of making engineering comparisons, analyses, and eval uations. This separation of functional elements is important because it allows the development of a framework within which to evaluate the impact of proposed changes and future technological advancements. For example, the means of transport in the collection of solid wastes has changed from the horse-drawn cart to the motor vehicle, but the fundamental method of collection-that is, the manual physical handling required-remains the same Waste generation Waste generation encompasses activities in which materials are identified as no longer being of value and are either thrown away or gathered together for disposal. For example, the wrapping of a candy bar is usually considered to be of little further value to the owner once the candy is consumed, and more often that not it is just thrown away, especially outdoors. It rtant in waste generation to note that there is an identification step and that this step varies with each individual waste Waste generation is, at present, an activity that is not very controllable. In the future, however, more control will be exercised over the generation of wastes. In states where waste diversion goals are set by law, and must be met under threat of economic penalty, it is necessary to put in place a manifest is now included in system evaluations as a method of limiting the quantity of waste generated anagers, system to monitor waste diversion. Source reduction, although not controlled by solid waste Waste Handling and Separation, Storage, and Processing at the Source. The second of the six functional elements in the solid waste management system is waste handling and separation, storage, and processing at the source. Waste handling and separation involves the activities associated with management of wastes until they are placed in storage containers for collection Handling also encompasses the movement of loaded containers to the point of collection. Separation of waste components is an important step in the handling and storage of solid waste at the source. For example, from the standpoint of materials specifications and revenues from the sale of recovered materials, the best place to separate waste materials for reuse and recvcling is at the source of generation. Homeowners are becoming more aware of the importance of separating newspaper and cardboard, bottles, yard wastes, aluminum cans, and ferrous materials. Currently, source separation of hazardous wastes by homeowners is being discussed widely and implemented to varying degrees On-site storage primary importance because of public health concerns and aesthetic considerations. Unsightly makeshift containers and even open ground storage, both of which are undesirable, are often seen at many residential and commercial sites. The cost of providing storage for solid wastes at the source is normally borne by the homeowner or apartment owner in the case of individuals, or by the management of commercial and industrial properties. Processing at the source Collection The functional element of collection, as used in this book, includes not only the gathering of solid wastes and recyclable materials, but also the transport of these materials, after collection, to the location where the collection vehicle is emptied. This location may be a materials processing facility, a
12-3 interdisciplinary relationships among such fields as political science, city and regional planning, geography, economics, public health, sociology, demography, communications, and conservation, as well as engineering and materials science. Functional Elements of a Waste Management System The problems associated with the management of solid wastes in today's society are complex because of the quantity and diverse nature of the wastes, the development of sprawling urban areas, the funding limitations for public services in many large cities, the impacts of technology, and the emerging limitations in both energy and raw materials. As a consequence, if solid waste management is to be accomplished in an efficient and orderly manner, the fundamental aspects and relationships involved must be identified, adjusted for uniformity of data, and understood clearly. In this text, the activities associated with the management of solid wastes, from the point of generation to final disposal have been grouped into the six functional elements: (1) waste generation; (2) waste handling and separation, storage, and processing at the source; (3) collection; (4) separation and processing and transformation of solid wastes; (5) transfer and transport; and (6) disposal. By considering each functional element separately, it is possible (1) to identify the fundamental aspects and relationships involved in each element and (2) to develop, where possible, quantifiable relationships for the purposes of making engineering comparisons, analyses, and evaluations. This separation of functional elements is important because it allows the development of a framework within which to evaluate the impact of proposed changes and future technological advancements. For example, the means of transport in the collection of solid wastes has changed from the horse-drawn cart to the motor vehicle, but the fundamental method of collection—that is, the manual physical handling required—remains the same . Waste Generation. Waste generation encompasses activities in which materials are identified as no longer being of value and are either thrown away or gathered together for disposal. For example, the wrapping of a candy bar is usually considered to be of little further value to the owner once the candy is consumed, and more often that not it is just thrown away, especially outdoors. It is important in waste generation to note that there is an identification step and that this step varies with each individual waste. Waste generation is, at present, an activity that is not very controllable. In the future, however, more control will be exercised over the generation of wastes. In states where waste diversion goals are set by law, and must be met under threat of economic penalty, it is necessary to put in place a manifest system to monitor waste diversion. Source reduction, although not controlled by solid waste managers, is now included in system evaluations as a method of limiting the quantity of waste generated. Waste Handling and Separation, Storage, and Processing at the Source. The second of the six functional elements in the solid waste management system is waste handling and separation, storage, and processing at the source. Waste handling and separation involves the activities associated with management of wastes until they are placed in storage containers for collection. Handling also encompasses the movement of loaded containers to the point of collection. Separation of waste components is an important step in the handling and storage of solid waste at the source. For example, from the standpoint of materials specifications and revenues from the sale of recovered materials, the best place to separate waste materials for reuse and recycling is at the source of generation. Homeowners are becoming more aware of the importance of separating newspaper and cardboard, bottles, yard wastes, aluminum cans, and ferrous materials. Currently, source separation of hazardous wastes by homeowners is being discussed widely and implemented to varying degrees. On-site storage is of primary importance because of public health concerns and aesthetic considerations. Unsightly makeshift containers and even open ground storage, both of which are undesirable, are often seen at many residential and commercial sites. The cost of providing storage for solid wastes at the source is normally borne by the homeowner or apartment owner in the case of individuals, or by the management of commercial and industrial properties. Processing at the source involves activities such as compaction and yard waste composting. Collection The functional element of collection, as used in this book, includes not only the gathering of solid wastes and recyclable materials, but also the transport of these materials, after collection, to the location where the collection vehicle is emptied. This location may be a materials processing facility, a
transfer station, or a landfill disposal site. In small cities, where final disposal sites are nearby, the hauling of wastes is not a serious problem. In large cities. however where the haul distance to the Where long distances are involved, transfer and transport facilities are normally used typically, collection is provided under various management arrangements, ranging from municipa services to franchised private services conducted under various forms of contracts. In several parts of the country, large solid waste disposal companies, with contracts in many cities, own and operat collection vehicles and landfill disposal sites. Collection services for industries vary widely. Some industrial wastes are handled like residential wastes; some companies have disposal sites on their own properties that use conveyor belts or water slurry transport. The latter is used for mineral wastes and agricultural wastes in many cases. Each industry requires an individual solution to its waste problems Separation, Processing, and Transformation of Solid Waste he separation, processing, and transformation of solid waste materials is the fourth of the functional elements. The recovery of separated materials, the separation and processing of solid waste components, and transformation of solid waste that occurs primarily in locations away from the source of waste generation are encompassed by this functional element. The types of means and facilities that are now used for the recovery of waste materials that have been separated at the source include curbside collection, drop off, and buy back centers. The separation and processing of wastes that have been separated at the source and the separation of commingled wastes usually occur at a materials recovery facilities, transfer stations, combustion facilities, and disposal sites. Processing often includes the separation of bulky items, separation of waste components by size using screens, manual separation of waste components, size reduction by shredding, separation of ferrous metals using magnets, volume reduction by compaction, and combustion Transformation processes are used to reduce the volume and weight of waste requiring disposal and to recover conversion products and energy. The organic fraction of municipal solid waste(Ms w) can be transformed by a variety of chemical and biological processes. The most commonly used chemical transformation process is combustion, which is used in conjunction with the recovery of energy in the form of heat. The most commonly used biological transformation process is aerobic composting. The selection of a given set of processes will depend on the waste management objectives to be achieved Transfer and Transport The functional element of transfer and transport involves two steps: (1)the transfer of wastes from the smaller collection vehicle to the larger transport equipment and(2)the subsequent transport of th wastes, usually over long distances, to a processing or disposal site. The transfer usually takes place at a transfer station. Although motor vehicle transport is most common rail cars and barges are also used For example, in the city of San Francisco the collection vehicles, which are relatively small because of the need to maneuver in city streets, haul their loads to a transfer station at the southern boundary of the city. At the transfer station, the wastes unloaded from the collection vehicles are reloaded into large tractor-trailer trucks. The loaded trucks are then driven to a disposal site located about 60 miles away The final functional element in the solid waste management system is disposal. Today the disposal of wastes by landfilling or landspreading is the ultimate fate of all solid wastes, whether they are residential wastes collected and transported directly to a landfill site, residual materials from materials recovery facilities(MRPs), residue from the combustion of solid waste, compost, or other substances from various solid waste-processing facilities. A modern sanitary landfill is not a dump: it is an engineered facility used for disposing of solid wastes on land or within the earth's mantle without creating nuisances or hazards to public health or safety, such as the breeding of rats and insects and the In most cities, planning for waste disposal involves dealing with city, county, or other regional planning commissions and agencies. Thus, land-use planning becomes a primary determinant in the selection, design, and operation of processing facilities and landfills. Environmental impact statements re require ed for all new landfill sites to ensure compliance with public health, aesthetics, and future
12-4 transfer station, or a landfill disposal site. In small cities, where final disposal sites are nearby, the hauling of wastes is not a serious problem. In large cities, however, where the haul distance to the point of disposal is often greater than 15 miles, the haul may have significant economic implications. Where long distances are involved, transfer and transport facilities are normally used. Typically, collection is provided under various management arrangements, ranging from municipal services to franchised private services conducted under various forms of contracts. In several parts of the country, large solid waste disposal companies, with contracts in many cities, own and operate collection vehicles and landfill disposal sites. Collection services for industries vary widely. Some industrial wastes are handled like residential wastes; some companies have disposal sites on their own properties that use conveyor belts or water slurry transport. The latter is used for mineral wastes and agricultural wastes in many cases. Each industry requires an individual solution to its waste problems. Separation, Processing, and Transformation of Solid Waste. The separation, processing, and transformation of solid waste materials is the fourth of the functional elements. The recovery of separated materials, the separation and processing of solid waste components, and transformation of solid waste that occurs primarily in locations away from the source of waste generation are encompassed by this functional element. The types of means and facilities that are now used for the recovery of waste materials that have been separated at the source include curbside collection, drop off, and buy back centers. The separation and processing of wastes that have been separated at the source and the separation of commingled wastes usually occur at a materials recovery facilities, transfer stations, combustion facilities, and disposal sites. Processing often includes the separation of bulky items, separation of waste components by size using screens, manual separation of waste components, size reduction by shredding, separation of ferrous metals using magnets, volume reduction by compaction, and combustion. Transformation processes are used to reduce the volume and weight of waste requiring disposal and to recover conversion products and energy. The organic fraction of municipal solid waste (MSW) can be transformed by a variety of chemical and biological processes. The most commonly used chemical transformation process is combustion, which is used in conjunction with the recovery of energy in the form of heat. The most commonly used biological transformation process is aerobic composting. The selection of a given set of processes will depend on the waste management objectives to be achieved. Transfer and Transport. The functional element of transfer and transport involves two steps: (1) the transfer of wastes from the smaller collection vehicle to the larger transport equipment and (2) the subsequent transport of the wastes, usually over long distances, to a processing or disposal site. The transfer usually takes place at a transfer station. Although motor vehicle transport is most common, rail cars and barges are also used to transport wastes. For example, in the city of San Francisco the collection vehicles, which are relatively small because of the need to maneuver in city streets, haul their loads to a transfer station at the southern boundary of the city. At the transfer station, the wastes unloaded from the collection vehicles are reloaded into large tractor-trailer trucks. The loaded trucks are then driven to a disposal site located about 60 miles away. Disposal. The final functional element in the solid waste management system is disposal. Today the disposal of wastes by landfilling or landspreading is the ultimate fate of all solid wastes, whether they are residential wastes collected and transported directly to a landfill site, residual materials from materials recovery facilities (MRPs), residue from the combustion of solid waste, compost, or other substances from various solid waste-processing facilities. A modern sanitary landfill is not a dump; it is an engineered facility used for disposing of solid wastes on land or within the earth's mantle without creating nuisances or hazards to public health or safety, such as the breeding of rats and insects and the contamination of groundwater. In most cities, planning for waste disposal involves dealing with city, county, or other regional planning commissions and agencies. Thus, land-use planning becomes a primary determinant in the selection, design, and operation of processing facilities and landfills. Environmental impact statements are required for all new landfill sites to ensure compliance with public health, aesthetics, and future use of land
12.4 Integrated Solid Water Management When all of the functional elements have been evaluated for use. and all of the interfaces and connections between elements have been matched for effectiveness and economy, the community has developed an integrated waste management sy stem, In this context integrated solid waste management (ISWM)can be defined as the selection and application of suitable techniques, technologies, and management programs to achieve specific waste management objectives and goals Hierarchy of Integrated Solid Waste Management A hierarchy(arrangement in order of rank) in waste management can be used to rank actions to implement programs within the community. The IS WM hierarchy adopted by the U.S. Environmental Protection Agency(EPA)is composed of the following elements: source reduction, recycling, waste combustion, and landfilling. The ISWM hierarchy used in this book is source reduction, recycling waste transformation, and landfilling. The term waste transfomation is substituted for the U.S. EPa term combustion, which is too limiting. In the broadest interpretation of the IS wM hierarchy, IS WM programs and systems should be developed in which the elements of the hierarchy are interrelated are selected to complement each other. For example, the separate collection of yard wastes can be to effect positively the operation of a waste-to-energy combustion facility Souree reduction The highest rank of the ISWM hierarchy, source reduction, involves reducing the amount and/or toxicity of the wastes that are now generated. Source reduction is first in the hierarchy because it is the most effective way to reduce the quantity of waste, the cost associated with its handling, and its environmental impacts. Waste reduction may occur through the design, manufacture, and packaging of products with minimum toxic content, minimum volume of material, or a longer useful life Waste reduction may also occur at the household, commercial, or industrial facility through selective buying patterns and the reuse of products and materials Recycli The second highest rank in the hierarchy is recycling, which involves(1)the separation and collection of waste materials; (2) the preparation of these materials for reuse, reprocessing, and remanufacture and (3)the reuse, reprocessing, and remanufacture of these materials. Recycling is an important factor in helping to reduce the demand on resources and the amount of waste requiring disposal by Waste Transformation The third rank in the IswM hierarchy, waste transformation, involves the physical, chemical, or biological alteration of wastes. Typically, the physical, chemical, and biological transformations that can be applied to MSW are used (1)to improve the efficiency of solid waste management operations and systems, (2)to recover reusable and recyclable materials, and (3)to recover conversion products (e. g, compost)and energy in the form of heat and combustible biogas. The transformation of waste materials usually results in the reduced use of landfill capacity. The reduction in waste volume through combustion is a well-known example. Landfilling. Ultimately, something must be done with(1) the solid wastes that cannot be recycled and are of no further use;(2)the residual matter remaining after solid wastes have been separated at a materials recovery facility; and(3)the residual matter remaining after the recovery of conversion products or energy. There are only two alternatives available for the long-term handling of solid wastes and residual matter: disposal on or in the earth's mantle, and disposal at the bottom of the ocean Landfilling, the fourth rank of the ISWM hierarchy, involves the controlled disposal of wastes on or in he earth's mantle, and it is by far the most common method of ultimate disposal for waste residuals Landfilling is the lowest rank in the IS wM hierarchy because it represents the least desirable means of dealing with society's wastes Planning for Integrated Waste Management Developing and implementing an ISWM plan is essentially a local activity that involves the selection of the proper mix of alternatives and technologies to meet changing local waste management needs while meeting legislative mandates. The proper mix of technologies, flexibility in meeting future changes, and the need for monitoring and evaluation are considered briefly in the following discussion and are considered in more detail throughout this text
12-5 12.4 Integrated Solid Water Management When all of the functional elements have been evaluated for use, and all of the interfaces and connections between elements have been matched for effectiveness and economy, the community has developed an integrated waste management system, In this context integrated solid waste management (ISWM) can be defined as the selection and application of suitable techniques, technologies, and management programs to achieve specific waste management objectives and goals. Hierarchy of Integrated Solid Waste Management A hierarchy (arrangement in order of rank) in waste management can be used to rank actions to implement programs within the community. The ISWM hierarchy adopted by the U.S. Environmental Protection Agency (EPA) is composed of the following elements: source reduction, recycling, waste combustion, and landfilling . The ISWM hierarchy used in this book is source reduction, recycling, waste transformation, and landfilling. The term waste transformation is substituted for the U.S. EPA's term combustion, which is too limiting. In the broadest interpretation of the ISWM hierarchy, ISWM programs and systems should be developed in which the elements of the hierarchy are interrelated and are selected to complement each other. For example, the separate collection of yard wastes can be used to effect positively the operation of a waste-to-energy combustion facility. Source Reduction. The highest rank of the ISWM hierarchy, source reduction, involves reducing the amount and/or toxicity of the wastes that are now generated. Source reduction is first in the hierarchy because it is the most effective way to reduce the quantity of waste, the cost associated with its handling, and its environmental impacts. Waste reduction may occur through the design, manufacture, and packaging of products with minimum toxic content, minimum volume of material, or a longer useful life. Waste reduction may also occur at the household, commercial, or industrial facility through selective buying patterns and the reuse of products and materials. Recycling. The second highest rank in the hierarchy is recycling, which involves (1) the separation and collection of waste materials; (2) the preparation of these materials for reuse, reprocessing, and remanufacture; and (3) the reuse, reprocessing, and remanufacture of these materials. Recycling is an important factor in helping to reduce the demand on resources and the amount of waste requiring disposal by landfilling. Waste Transformation. The third rank in the ISWM hierarchy, waste transformation, involves the physical, chemical, or biological alteration of wastes. Typically, the physical, chemical, and biological transformations that can be applied to MSW are used (1) to improve the efficiency of solid waste management operations and systems, (2) to recover reusable and recyclable materials, and (3) to recover conversion products (e.g., compost) and energy in the form of heat and combustible biogas. The transformation of waste materials usually results in the reduced use of landfill capacity. The reduction in waste volume through combustion is a well-known example. Landfilling. Ultimately, something must be done with (1) the solid wastes that cannot be recycled and are of no further use; (2) the residual matter remaining after solid wastes have been separated at a materials recovery facility; and (3) the residual matter remaining after the recovery of conversion products or energy. There are only two alternatives available for the long-term handling of solid wastes and residual matter: disposal on or in the earth's mantle, and disposal at the bottom of the ocean. Landfilling, the fourth rank of the ISWM hierarchy, involves the controlled disposal of wastes on or in the earth's mantle, and it is by far the most common method of ultimate disposal for waste residuals. Landfilling is the lowest rank in the ISWM hierarchy because it represents the least desirable means of dealing with society's wastes. Planning for Integrated Waste Management Developing and implementing an ISWM plan is essentially a local activity that involves the selection of the proper mix of alternatives and technologies to meet changing local waste management needs while meeting legislative mandates. The proper mix of technologies, flexibility in meeting future changes, and the need for monitoring and evaluation are considered briefly in the following discussion and are considered in more detail throughout this text
Proper Mix of Alternatives and Technologies. A wide variety of alternative programs and technologies are now available for the management of solid wastes. Several questions arise from this variety: What is the proper mix between(1)the am of waste separated for reuse and recycling, (2)the amount of waste that is composted, (3)the amount of waste that is combusted, and(4)the amount of waste to be disposed of in landfills? What technology should be used for collecting wastes separated at the source, for separating waste omponents at MRFs, for composting the organic fraction of Msw, and for compacting wastes at a landfill? What is the proper timing for the application of various technologies in an IS WM system and ow should decisions be made? Because of the wide range of participants in the decision-making process for the implementation of solid waste management systems, the selection of the proper mix of alternatives and technologies for the effective management of wastes has become a difficult, if not impossible, task. The development of effective IS WM systems will depend on the availability of reliable data on the characteristics of the waste stream, performance specifications for alternative technologies, and adequate cost information. Flexibility in Meeting Future Changes The ability to adapt waste management practices to changing conditions is of critical importance in the development of an IS WM system. Some important factors to consider include(D) changes in the quantities and composition of the waste stream. (2) changes in the specifications and markets for recyclable materials, and (3) rapid developments in technology. If the IS wM system is planned and designed on the basis of a detailed analysis of the range of possible outcomes related to these factors, the local community will be protected from unexpended changes in local, regional, and larger-scale Monitoring and evaluation. Integrated solid waste management is an ongoing activity that requires continual monitoring and evaluation to determine if program objectives and goals(e.g, waste diversion goals) are being met Only by developing and implementing ongoing monitoring and evaluation programs can timely changes be made to the ISwM system that reflect changes in waste characteristics, changing specifications and markets for recovered materials, and new and improved waste management technologies 12.5 Operation of Solid Waste Management Systems The facilities that compose a solid waste management system are often identified as solid waste management system units. The planning and engineering of solid waste management units include social, political, and technical factors. The combination of all of these factors forms a series of issues that must be addressed by community decision makers. Some contemporary solid waste management issues and future challenges and opportunities are introduced in the following discussion; these subjects will also be addressed in greater detail later in the text Management issues In addition to meeting the requirements associated with IS wM, a number of other management issues must be addressed in the operation of ISWM systems. The solid waste practitioner must acknowledge these management issues or face a high risk of failure in the implementation of solid waste management programs. Setting Workable but Protective Regulatory Standards. Solid waste management units are subject to an increasing number of regulations. The attention is justified and timely, but strict adherence to very protective regulatory standards often causes failure of the processes by which waste management units are put in place Municipal solid waste management is caught in the backlash of understandable public concern over hazardous waste management. Regulatory agencies. in setting standards for construction, operation, data derived from experiments with massive doses of toxic compounds. Municipal waste does no contain massive quantities of toxics, but it does contain the small amounts found in the wastes from normal household activities. An unworkable regulation is one that ignores reality and deals only with certain technical data
12-6 Proper Mix of Alternatives and Technologies. A wide variety of alternative programs and technologies are now available for the management of solid wastes. Several questions arise from this variety: What is the proper mix between (1) the amount of waste separated for reuse and recycling, (2) the amount of waste that is composted, (3) the amount of waste that is combusted, and (4) the amount of waste to be disposed of in landfills? What technology should be used for collecting wastes separated at the source, for separating waste components at MRFs, for composting the organic fraction of MSW, and for compacting wastes at a landfill? What is the proper timing for the application of various technologies in an ISWM system and how should decisions be made? Because of the wide range of participants in the decision-making process for the implementation of solid waste management systems, the selection of the proper mix of alternatives and technologies for the effective management of wastes has become a difficult, if not impossible, task. The development of effective ISWM systems will depend on the availability of reliable data on the characteristics of the waste stream, performance specifications for alternative technologies, and adequate cost information. Flexibility in Meeting Future Changes. The ability to adapt waste management practices to changing conditions is of critical importance in the development of an ISWM system. Some important factors to consider include (1) changes in the quantities and composition of the waste stream, (2) changes in the specifications and markets for recyclable materials, and (3) rapid developments in technology. If the ISWM system is planned and designed on the basis of a detailed analysis of the range of possible outcomes related to these factors, the local community will be protected from unexpended changes in local, regional, and larger-scale conditions. Monitoring and Evaluation. Integrated solid waste management is an ongoing activity that requires continual monitoring and evaluation to determine if program objectives and goals (e.g., waste diversion goals) are being met . Only by developing and implementing ongoing monitoring and evaluation programs can timely changes be made to the ISWM system that reflect changes in waste characteristics, changing specifications and markets for recovered materials, and new and improved waste management technologies. 12.5 Operation of Solid Waste Management Systems The facilities that compose a solid waste management system are often identified as solid waste management system units. The planning and engineering of solid waste management units include social, political, and technical factors. The combination of all of these factors forms a series of issues that must be addressed by community decision makers. Some contemporary solid waste management issues and future challenges and opportunities are introduced in the following discussion; these subjects will also be addressed in greater detail later in the text. Management Issues In addition to meeting the requirements associated with ISWM, a number of other management issues must be addressed in the operation of ISWM systems. The solid waste practitioner must acknowledge these management issues or face a high risk of failure in the implementation of solid waste management programs. Setting Workable but Protective Regulatory Standards. Solid waste management units are subject to an increasing number of regulations. The attention is justified and timely, but strict adherence to very protective regulatory standards often causes failure of the processes by which waste management units are put in place. Municipal solid waste management is caught in the backlash of understandable public concern over hazardous waste management. Regulatory agencies, in setting standards for construction, operation, and monitoring of units, are beset by lawyers and environmental groups recently armed with scientific data derived from experiments with massive doses of toxic compounds. Municipal waste does not contain massive quantities of toxics, but it does contain the small amounts found in the wastes from normal household activities. An unworkable regulation is one that ignores reality and deals only with certain technical data
Improving Scientific Methods for Interpretation of Data The need to know about hazards in the environment has generated large amounts of data on toxics Billions of dollars have been invested in analytical equipment, laboratories, and data accumulation since the passage of the Comprehensive Environmental Response Compensation and Liability Act (CERCLA). Even with all the data, however, there is a lack of a uniform basis for data interpretation Analytical equipment and laboratory techniques produce data with accuracy in parts per billion or parts per trillion. What does such a detection accuracy mean to a solid waste management unit? If the component detected at a solid waste management system unit is on a regulatory list of cancer-causing agents, the unit may be shut down The goal is to understand the effects of very small quantities of toxic components on the environment In the meantime, how much data should be presented to the public? When should data be delivered to the public? How does the public participate in data gathering and interpretation? Identification of Hazardous and Toxic Consumer Products Requiring Special Waste Management Units. Municipal solid waste is a heterogeneous mass made up of every discard from homes, businesses, and institutions. Although small in quantity, some discards are hazardous, as identified on the product container. Examples are bleach, cleaning fluids, insecticides, and gasoline. The issue is whether household hazardous waste contaminates the municipal waste management unit and whether, because of the large land areas in landfills, certain household wastes should be removed from the garbage How will the consumer store hazardous discards until they are picked up or delivered to the specl for disposal in smaller, highly controlled waste management units. Which products are most hazardous management unit? Who will set up and operate special waste management units as such units will be defined by regulators as hazardous waste units? Paying for Improved Waste Management Units Solid waste management has a tradition of low cost. The improvements demanded by a concerned public are more costly than past practices. The increased costs must be paid by waste generators. This issue involves changing the manner in which a consumer thinks about paying for waste disposal. How is the cost of waste disposal presented to the consumer? When is the consumer asked to pav-at the time of product purchase or when the product is discarded? Since solid waste decays very slowly, who pays for long-term maintenance of land disposal waste management units-the generator at the time of discard or future users as maintenance costs are incurred? Designating Land Disposal Units at or near Large Urban Centers. Waste management units are difficult to place in an urban environment. A suspicious public views these units as open dumps and littered transfer stations served by odorous, dripping garbage collection ucks. Yet it is within urban centers that the greatest quantity of solid waste is generated. Urban land use planning is facing a severe challenge to provide designated waste land disposal units The issues are identifying environmentally acceptable land areas for land disposal units and then preserving lands for the intended use. Who will set a standard for"environmentally acceptable"? Will different standards apply for urban and rural areas? Can a scientific basis be identified that will satisfy a suspicious public regarding the safety of land disposal units? Establishing and Maintaining More Qualified Managers to Develop and Operate waste Management units. Solid waste management units are increasing in quantity and complexity. In response, a set of managers must be trained and put in the appropriate positions to develop and operate expanded and improved management units The goal is to develop the human resources needed to develop and operate waste management units Who will train the managers? How will the cost of training be paid? What standards will apply during the interim period while managers receive training? Future Challenges and Opportunities he multibillion-dollar industry of solid waste management can be supported only by the public which is responsible for the generation of the vast tonnage of wastes. Public attitudes must be modified to reduce the environmental and economic burden placed on society for the disposal of solid waste. National concern must transcend the question of cost in an attempt to implement whateve
12-7 Improving Scientific Methods for Interpretation of Data. The need to know about hazards in the environment has generated large amounts of data on toxics. Billions of dollars have been invested in analytical equipment, laboratories, and data accumulation since the passage of the Comprehensive Environmental Response Compensation and Liability Act (CERCLA) . Even with all the data, however, there is a lack of a uniform basis for data interpretation. Analytical equipment and laboratory techniques produce data with accuracy in parts per billion or parts per trillion. What does such a detection accuracy mean to a solid waste management unit? If the component detected at a solid waste management system unit is on a regulatory list of cancer-causing agents, the unit may be shut down. The goal is to understand the effects of very small quantities of toxic components on the environment. In the meantime, how much data should be presented to the public? When should data be delivered to the public? How does the public participate in data gathering and interpretation? Identification of Hazardous and Toxic Consumer Products Requiring Special Waste Management Units. Municipal solid waste is a heterogeneous mass made up of every discard from homes, businesses, and institutions. Although small in quantity, some discards are hazardous, as identified on the product container. Examples are bleach, cleaning fluids, insecticides, and gasoline. The issue is whether household hazardous waste contaminates the municipal waste management unit and whether, because of the large land areas in landfills, certain household wastes should be removed from the garbage can for disposal in smaller, highly controlled waste management units. Which products are most hazardous? How will the consumer store hazardous discards until they are picked up or delivered to the special management unit? Who will set up and operate special waste management units as such units will be defined by regulators as hazardous waste units? Paying for Improved Waste Management Units. Solid waste management has a tradition of low cost. The improvements demanded by a concerned public are more costly than past practices . The increased costs must be paid by waste generators. This issue involves changing the manner in which a consumer thinks about paying for waste disposal. How is the cost of waste disposal presented to the consumer? When is the consumer asked to pay—at the time of product purchase or when the product is discarded? Since solid waste decays very slowly, who pays for long-term maintenance of land disposal waste management units—the generator at the time of discard or future users as maintenance costs are incurred? Designating Land Disposal Units at or near Large Urban Centers. Waste management units are difficult to place in an urban environment. A suspicious public views these units as open dumps and littered transfer stations served by odorous, dripping garbage collection trucks. Yet it is within urban centers that the greatest quantity of solid waste is generated. Urban land use planning is facing a severe challenge to provide designated waste management units, especially land disposal units. The issues are identifying environmentally acceptable land areas for land disposal units and then preserving lands for the intended use. Who will set a standard for "environmentally acceptable"? Will different standards apply for urban and rural areas? Can a scientific basis be identified that will satisfy a suspicious public regarding the safety of land disposal units? Establishing and Maintaining More Qualified Managers to Develop and Operate Waste Management Units. Solid waste management units are increasing in quantity and complexity. In response, a set of managers must be trained and put in the appropriate positions to develop and operate expanded and improved management units. The goal is to develop the human resources needed to develop and operate waste management units. Who will train the managers? How will the cost of training be paid? What standards will apply during the interim period while managers receive training? Future Challenges and Opportunities The multibillion-dollar industry of solid waste management can be supported only by the public, which is responsible for the generation of the vast tonnage of wastes. Public attitudes must be modified to reduce the environmental and economic burden placed on society for the disposal of solid waste. National concern must transcend the question of cost in an attempt to implement whatever
individual or societal action is necessary Unfortunately, the standard of living in the United States is inevitably tied to the generation of solid reasonable to assume that a departure from this philosophy of wastefulness will reduce the tonnage of wastes to be managed. This concept inevitably leads to the need for source reduction and the reuse cycling of recovered materials Changing Consumption Habits in Society Product consumption is a natural activity. Society changes its standard of living by changing the quantity and quality of products it consumes. Solid wastes, the discards of product consumption, vary in quantity and quality as changes occur in the standard of living. Consumption habits must be changed if the quantity of solid wastes from consuming activities is to be reduced. The challenge is to change consumption habits that have been established over many years, as a result of advertising pressure that glamorizes increased Reducing the volume of waste at the source. Efforts must be made to reduce the quantity of materials used in both packaging and obsolescent goods and to begin the process of recycling at the source-the home, office, or factory-so that fewer naterials will become part of the disposable solid wastes of a community. Source reduction is an alternative that will conserve resources and also has economic viability Making landfills safer. Landfills will always be the final disposal place for wastes that cannot be recovered. For this reason, every effort must be made to reduce the toxicity of the wastes that will ultimately be placed in landfills The design of landfills must also improve to provide the safest possible location for the long-term storage of waste materials. The data base for existing landfills is expanding as improved construction and operations are implemented at new facilities. With an expanded data base comes the opportunity to understand how landfills function and how to manage the wastes placed in landfills more Development of New Technologies. There are numerous opportunities to introduce new technologies into the solid waste management system. The challenge is to encourage the development of technologies that are most conservative of natural resources and that are cost-effective. Because many unproven technologies have been sold to unsuspecting cities, it may be necessary to write laws to regulate the use of technology. The testing and implementing of new technologies will be an important part of IS wM in the future
12-8 individual or societal action is necessary. Unfortunately, the standard of living in the United States is inevitably tied to the generation of solid wastes—the squandering of natural resources from this country and abroad, the one-time use of materials of so many types, and the philosophy of wastefulness and rapid obsolescence of products. It is reasonable to assume that a departure from this philosophy of wastefulness will reduce the tonnage of wastes to be managed. This concept inevitably leads to the need for source reduction and the reuse and recycling of recovered materials. Changing Consumption Habits in Society. Product consumption is a natural activity. Society changes its standard of living by changing the quantity and quality of products it consumes. Solid wastes, the discards of product consumption, vary in quantity and quality as changes occur in the standard of living. Consumption habits must be changed if the quantity of solid wastes from consuming activities is to be reduced. The challenge is to change consumption habits that have been established over many years, as a result of advertising pressure that glamorizes increased consumption. Reducing the Volume of Waste at the Source. Efforts must be made to reduce the quantity of materials used in both packaging and obsolescent goods and to begin the process of recycling at the source—the home, office, or factory—so that fewer materials will become part of the disposable solid wastes of a community. Source reduction is an alternative that will conserve resources and also has economic viability. Making Landfills Safer. Landfills will always be the final disposal place for wastes that cannot be recovered. For this reason, every effort must be made to reduce the toxicity of the wastes that will ultimately be placed in landfills. The design of landfills must also improve to provide the safest possible location for the long-term storage of waste materials. The data base for existing landfills is expanding as improved construction and operations are implemented at new facilities. With an expanded data base comes the opportunity to understand how landfills function and how to manage the wastes placed in landfills more effectively. Development of New Technologies. There are numerous opportunities to introduce new technologies into the solid waste management system. The challenge is to encourage the development of technologies that are most conservative of natural resources and that are cost-effective. Because many unproven technologies have been sold to unsuspecting cities, it may be necessary to write laws to regulate the use of technology. The testing and implementing of new technologies will be an important part of ISWM in the future