.206 北京科技大学学报 第35卷 4 结论 (6]Bohmer H J.Residual stresses and material behavior of (1)经渗碳处理的M50NL轴承钢磨削表面致 M50NiL and RBD /ASTM STP 1195 Creative Use of Bearing Steels.West Conshohocken:American Society 密洁净、平整光滑及纹理浅细，因磨削纹理导致的 for Testing and Materials,1993:34 应力集中系数较小，磨削过程中材料以塑性变形方 [7]CBS-50NiL VIM-VAR:High performance carburizing 式被去除. bearing and gear steel /Alloy Digest,Steel-Alloy Col- (2)磨削在渗碳层基础上叠加了一个表面变质 lection 1952-2010.ASM International,1992 层.磨削表面显微硬度提高约HRC1.2,磨削影响 [8 Braza J F,Pearson P K.Tribological and metallurgical 显微硬度的深度为80um. evaluation of ferritic nitrocarburized M-50 and M-50 NiL (3)磨削表面残余压应力明显提高，可高达- steels /ASTM STP 1195 Creative Use of Bearing Steels. 500MPa以上，磨削影响残余压应力的深度为20 West Conshohocken:American Society for Testing and Materials,1993:49 um. 9 Zang X Z.Electron Microscopy and Analysis.Beijing: (4)磨削表面变质层微观组织的基本特征是变 Tsinghua University Press,2006 形和组织细化，在选区电子衍射图上，由圆形衍射 (章晓中.电子显微分析.北京：清华大学出版社，2006) 斑点转变为周向拉长的弧形斑点，由单晶的电子衍 [10]Lou YZ,Liu D L,Mao X P,et al.Titanium carbonitrides 射谱转变为多晶的电子衍射环.选区电子衍射方法 in Ti-microalloyed steels produced by CSP process.Iron 表征的磨削变质层纳米晶厚度约0.5m.通过透射 Steel,2010,45(2):70 电子显微镜，采用选区电子衍射的方法可以相对准 (娄艳芝，柳得橹，毛新平，等.CSP工艺钛微合金钢中的 确且直观地反映磨削表面变质层厚度特征 碳氮化钛析出相.锅铁，2010,45(2)：70) 11)Lou Y Z,Li C Z,Liu D L.TEM observation of TiC pre- cipitates nucleated on Ti2CS and determination of orien- 参考文献 tation relationships.J Univ Sci Technol Beijing,2010, 32(4):438 [1]Yang Y Y,Fang H S,Huang W G.Study on wear resis- (娄艳芝，李春志，柳得椎.TiC在T2CS上形核生长的 tance of the white layer.Tribol /nt,1996,29(5):425 电镜观察及其取向关系的测定.北京科技大学学报，2010， [2]Gao C Q.Friction Metallography.Harbin:Harbin Insti- 32(4):438) tute of Technology Press,1988 12 Luo Q H,Li C Z,Lou YZ,et al.Grinding process effect (高彩桥.摩擦金属学，哈尔滨：哈尔滨工业大学出版社， on surface modificative layer microstructure,property and 1988.) fatigue behavior of carburized M50NiL,steel.Acta Metall [3]Lou Y Z.A Study of Modificative Layer and Antifa- Sin,2012,48(2:194 tigue Mechanism of Integrity Grinding on the Carburized (罗庆洪，李春志，娄艳芝，等.磨削工艺对渗碳M50NiL M50NiL Steel [Postdoctoral Research].Beijing:Beijing 钢表面变质层微观结构和性能及疲劳性能影响，金属学 Institute of Aeronautical Materials,2011 报，2012,48(2)：194) (娄艳芝.超硬磨削表面变质层与抗疲劳机理研究「博士后 [13]Arola D,Ramulu M.An examination of the effects from 研究工作报告.北京：北京航空材料研究院，2011) surface texture on the strength of fiber-reinforced plastics [4]Wang C J,Lu D Q,Wu J X,et al.Carburizing Bearing J Compos Mater,1999,33(2):101 Steel and Heat Treatment.Beijing:Ordnance Industry [14]Arola D,Williams C L.Estimating the fatigue stress com Press.1989 centration factor of machined surfaces.Int J Fatigue, (汪传稷，陆大启，吴继贤，等.渗碳轴承用钢及其热处理 2002,24:923 北京：兵器工业出版杜，1989) [15]Luo Q H,Lu Y H,Lou Y Z,et al.Transmission electron [5]Yu Y,Zhu G H.Measurement of grinding affected layer microscopy study on microstructures of two hard coating depth of bearing ring made from Cr4Mo4V steel.Phys deposited by magnetron sputtering.Mod Sci Instrum, Test Chem Anal Part A Phys Test,2011,47(5):270 2009(4:15 (于芸，朱光辉.Cr4Mo4V钢制轴承套圈磨削变质层深度 (罗庆洪，陆永浩，娄艳芝，等.两种陶瓷薄膜的透射电镜 的测定.理化检测：物理分册，2011,47(5)小：270) 研究.现代科学仪器.2009(4)：15)