《复合材料 Composites》课程教学资源（学习资料）第五章 陶瓷基复合材料_fibrous monoliths-9

AERIALS SHENGE ENGINEERIG SEVIER Materials Science and Engineering A 380(2004)237-244 www.elsevier.com/locate/msea Fibrous monoliths of mullite-AlPO4 and alumina/YAG-alumina platelets Dong-Kyu Kim, Waltraud M. Kriven* Department of Materials Science and Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801 USA Received 30 May 2003 received in revised form 23 March 2004 Abstract Two-layer, fibrous monolithic composites consisting of mullite-aluminum phosphateAlPO4)and 50 vol. alumina: 50 vol. YAG in situ composite matrix-alumina platelet interphase components, were fabricated by a co-extrusion technique. The four powders were characterized for particle size, specific surface area, and SEM analysis. The mixing formulations for extruding the powders were developed using ethylene vinylacetate copolymer as a binder. The variation in the mixing torque, in a Brabender mixer, as a function of temperature was measured The binder removal behavior of the mullite-AIPO4 fibrous monolithic composite was studied by thermogravimetric analysis (TGA). The AlPO4 and alumina platelet interphase layers formed a porous and less porous interphase region, respectively, after sintering. The sintered mullite-AlPO4 two-layer fibrous monolithic showed non-brittle fracture behavior. Its 3-point bend strength and work of fracture were 76+ MPa and 0.45+0.02 kJ/m", respectively O 2004 Elsevier B v. All rights reserved Keywords: Fibrous monolithic composite; Mullite-aluminum phosphate(AlPO4): 50 vol. Alumina: 50 vol. YAG in situ composite-alumina platelet, Sintering, Mechanical property 1. Introduction ing from 1200 to 1400C[12, 15-18]. Mullite is known to be an excellent creep resistant material. Lessing et al. 191 To overcome the brittleness of ceramics, several different reported the creep rate of mullite to be, approximately, an approaches have been adopted. After the work of Clegg et al. order of magnitude less than that of Al2O3 [1] different kinds of laminated ceramic composites were YAG (yttrium aluminum garnet, Y3AlsO12)and alumina made to increase toughness [2-6]. Fibrous monolithic com- are chemically compatible with each other and can constitute osites are an alternative approach to the design of tough structurally sound composites [20-22]. YAG-alumina eutec ceramics, without the incorporation of ceramic fibers into a tic materials have been made by induction heating [23-25 composite. This concept was first introduced by Coblenz[7]. The alumina-YAG eutectic composite has a flexural strength Fibrous monolithic composites are sintered (or hot-pressed) of 360-500 MPa. This strength is maintained nearly con- monolithic ceramics with a distinct fibrous texture, consist- stantly over the range from room temperature to 1700C ing of cells of a primary phase, separated by cell boundaries [25-28]. The creep resistance of the alumina-YAG eutec of a tailored secondary phase[8. Halloran et al. [8-ll con- tic composite is better than that of polycrystalline YAG and ducted extensive research on non-oxide, fibrous monolithic that of a-axis sapphire fiber [28]. An alumina-YAG eutectic composites of SiC/C and Si3 N4/BN composite has excellent high temperature strength and creep Mullite is an attractive structural material due to its excel- resistance, but its processing route is complicated and ex lent strength and creep resistance at high temperatures, low pensive. Therefore, as an alternative route to the benefits of thermal expansion and conductivity, good thermal stability, a eutectic composite, an alternative, cheap, alumind-YAG in and chemical inertness [12-14. The reported bend strengths situ matrix composite was developed in our laboratory [291 of mullite at room temperature lie between 250-400 MPa, Aluminum phosphate(AlPO4) is chemically compatible and these strengths are maintained up to temperatures rang- with mullite and has a density corresponding to 61% of the- strength of1.5±02 after sintering at 1600C for 10h, resulting in AlPO4 act- Corresponding author. Tel. +12173335258; fax: +1217 2736. ing as a chemically stable, porous, and weak interphase E-mail address: w-kriven staff uiuc. edu(WM. Riven material [30]- Alumina platelets were aligned in random 0921-5093/s-see front matter 2004 Elsevier B V. All rights reserved doi:10.1016 j.msea200403.083

Materials Science and Engineering A 380 (2004) 237–244 Fibrous monoliths of mullite-AlPO4 and alumina/YAG-alumina platelets Dong-Kyu Kim, Waltraud M. Kriven∗ Department of Materials Science and Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801 USA Received 30 May 2003; received in revised form 23 March 2004 Abstract Two-layer, fibrous monolithic composites consisting of mullite-aluminum phosphate (AlPO4) and 50 vol.% alumina:50 vol.% YAG in situ composite matrix–alumina platelet interphase components, were fabricated by a co-extrusion technique. The four powders were characterized for particle size, specific surface area, and SEM analysis. The mixing formulations for extruding the powders were developed using ethylene vinylacetate copolymer as a binder. The variation in the mixing torque, in a Brabender mixer, as a function of temperature was measured. The binder removal behavior of the mullite-AlPO4 fibrous monolithic composite was studied by thermogravimetric analysis (TGA). The AlPO4 and alumina platelet interphase layers formed a porous and less porous interphase region, respectively, after sintering. The sintered mullite-AlPO4 two-layer fibrous monolithic showed non-brittle fracture behavior. Its 3-point bend strength and work of fracture were 76 ± 5 MPa and 0.45 ± 0.02 kJ/m2, respectively. © 2004 Elsevier B.V. All rights reserved. Keywords: Fibrous monolithic composite; Mullite-aluminum phosphate(AlPO4); 50 vol.% Alumina:50 vol.% YAG in situ composite-alumina platelet; Sintering; Mechanical property 1. Introduction To overcome the brittleness of ceramics, several different approaches have been adopted. After the work of Clegg et al. [1], different kinds of laminated ceramic composites were made to increase toughness [2–6]. Fibrous monolithic com￾posites are an alternative approach to the design of tough ceramics, without the incorporation of ceramic fibers into a composite. This concept was first introduced by Coblenz [7]. Fibrous monolithic composites are sintered (or hot–pressed) monolithic ceramics with a distinct fibrous texture, consist￾ing of cells of a primary phase, separated by cell boundaries of a tailored secondary phase [8]. Halloran et al. [8–11] con￾ducted extensive research on non-oxide, fibrous monolithic composites of SiC/C and Si3N4/BN. Mullite is an attractive structural material due to its excel￾lent strength and creep resistance at high temperatures, low thermal expansion and conductivity, good thermal stability, and chemical inertness [12–14]. The reported bend strengths of mullite at room temperature lie between 250–400 MPa, and these strengths are maintained up to temperatures rang- ∗ Corresponding author. Tel.: +1 217 333 5258; fax: +1 217 333 2736. E-mail address: w-kriven@staff.uiuc.edu (W.M. Kriven). ing from 1200 to 1400 ◦C [12,15–18]. Mullite is known to be an excellent creep resistant material. Lessing et al. [19] reported the creep rate of mullite to be, approximately, an order of magnitude less than that of Al2O3. YAG (yttrium aluminum garnet, Y3Al5O12) and alumina are chemically compatible with each other and can constitute structurally sound composites[20–22]. YAG–alumina eutec￾tic materials have been made by induction heating [23–25]. The alumina–YAG eutectic composite has a flexural strength of 360–500 MPa. This strength is maintained nearly con￾stantly over the range from room temperature to 1700 ◦C [25–28]. The creep resistance of the alumina–YAG eutec￾tic composite is better than that of polycrystalline YAG and that of a-axis sapphire fiber [28]. An alumina–YAG eutectic composite has excellent high temperature strength and creep resistance, but its processing route is complicated and ex￾pensive. Therefore, as an alternative route to the benefits of a eutectic composite, an alternative, cheap, alumina–YAG in situ matrix composite was developed in our laboratory [29]. Aluminum phosphate (AlPO4) is chemically compatible with mullite and has a density corresponding to 61% of the￾oretical value. It has a bending strength of 1.5 ± 0.2 MPa after sintering at 1600 ◦C for 10 h, resulting in AlPO4 act￾ing as a chemically stable, porous, and weak interphase material [30]. Alumina platelets were aligned in random, 0921-5093/$ – see front matter © 2004 Elsevier B.V. All rights reserved. doi:10.1016/j.msea.2004.03.083

D-K. Kim, W.M. Kriven/Materials Science and Engineering 4 380 (2004)237-244 Table I Mixing formulations for the oxide powders Binder(Elvax) Plasticizer(P) Lubricant(SA) 21 10 220 50 vol% Al203 2.4 40.8 50 voL% YAG In situ composite AlPO 40 9.6 4.4 AlO3 platelets 9.6 4.4 Note: All ingredients are in vol%, elvax: ethylene vinylacetate copolymer(Dupont, 210, 220, and 250 are products names, indicating a molecular weight crease from 210, 220 to 250), DP: dibutyl phthalate(99%, Aldrich), SA: stearic acid (95%, Aldrich). three-dimensional orientations, and induced constrained sin- 210, 220 to 250. The reason for using the mixture was to tering of ceramic powders, finally functioning as a debond- facilitate the binder removal process over a broad temper- ing interphase in the composite structures [3 ature range. Dibutyl phthalate(Aldrich, 99%)and stearic In this research, the processing of an oxide matrix-oxide acid(Aldrich, 95%)were used as a plasticizer and lubricant, nterphase, 2-layer, fibrous monolithic composite was respectively studied. Mullite and a 50 vol. alumina: 50 vol. YAG Ceramic powder, binder, plasticizer, and lubricant were in situ composite were used as possible high tempera- mixed in a computer controlled, high shear mixer(Model ture, structural, matrix materials. Aluminum phosphate 2100, C. W. Brabender, N). The mixing formulation is (AlPO4) and alumina platelets were investigated as inter- shown in Table 1. To make the fibrous monolithic texture phase materials. A two-layer, mullite-AlPO4 and a 50 vol. without intermixing between inner mullite matrix and AlPO4 alumina: 50 vol. YAG in situ composite matrix-alumina platelet, fibrous monolithic material were fabricated by co-extrusion using ethylene vinylacetate(EVA) copolymer as a binder. The powders used for making composites were characterized. The microstructure and room temperature mechanical behavior of the two composites were investi- 2. Experimental procedure platelet powders of 5-10 um diameter by I um thick(Elf Atochem, France) were used. AlPO4 and 50 vol % alu mina: 50 vol. YAG in situ composite powders were syn hesized by the organic, steric entrapment method [32-371 (a) The particle size of the powder was measured in a centrifu- gal, automated, particle size distribution analyzer (Model CAPA-700, Horiba, Kyoto, Japan). The specific surface area of samples was measured from seven-point BET analyses using nitrogen gas adsorption(Model ASAP2400, Micro- metrics,Norcross, GA). The bulk density of sintered alu mina platelet pellets was measured by Archimedes method (ASTM C373). The morphology of powders and the mi- crostructure of composites were investigated by scanning electron microscopy (SEM, Model S-4700, Hitachi, Osaka, Japan). The composite pellets for SEM were polished down to a 1 um using diamond paste finish, and then thermally etched at 1550C for 30 min A mixture of Elvax 210, 220, and 250 ethylene vinyl ac etate copolymers(Dupont, Wilmington, DEL) was used as binder phases. The molecular weight increased from Elvax Fig. 1. The stainless steel mouldings(a)and extrusion(b)dies

238 D.-K. Kim, W.M. Kriven / Materials Science and Engineering A 380 (2004) 237–244 Table 1 Mixing formulations for the oxide powders Powder Binder (Elvax) Plasticizer (DP) Lubricant (SA) 210 220 250 Mullite 50 vol.% Al2O3 52 2.4 4.8 40.8 – – 50 vol.% YAG 52 2.4 4.8 40.8 – – In situ composite AlPO4 40 9.6 24 14.4 9 3 Al2O3 platelets 40 9.6 24 14.4 9 3 Note: All ingredients are in vol%, elvax: ethylene vinylacetate copolymer (Dupont, 210, 220, and 250 are products names, indicating a molecular weight increase from 210, 220 to 250); DP: dibutyl phthalate (99%, Aldrich), SA: stearic acid (95%, Aldrich). three-dimensional orientations, and induced constrained sin￾tering of ceramic powders, finally functioning as a debond￾ing interphase in the composite structures [31]. In this research, the processing of an oxide matrix–oxide interphase, 2-layer, fibrous monolithic composite was studied. Mullite and a 50 vol.% alumina:50 vol.% YAG in situ composite were used as possible high tempera￾ture, structural, matrix materials. Aluminum phosphate (AlPO4) and alumina platelets were investigated as inter￾phase materials. A two-layer, mullite-AlPO4 and a 50 vol.% alumina:50 vol.% YAG in situ composite matrix–alumina platelet, fibrous monolithic material were fabricated by co-extrusion using ethylene vinylacetate (EVA) copolymer as a binder. The powders used for making composites were characterized. The microstructure and room temperature mechanical behavior of the two composites were investi￾gated. 2. Experimental procedure Commercial mullite (Kyoritsu, KM 101) and alumina platelet powders of 5–10
m diameter by 1
m thick (Elf Atochem, France) were used. AlPO4 and 50 vol.% alu￾mina:50 vol.% YAG in situ composite powders were syn￾thesized by the organic, steric entrapment method [32–37]. The particle size of the powder was measured in a centrifu￾gal, automated, particle size distribution analyzer (Model CAPA-700, Horiba, Kyoto, Japan). The specific surface area of samples was measured from seven-point BET analyses using nitrogen gas adsorption (Model ASAP2400, Micro￾metrics, Norcross, GA). The bulk density of sintered alu￾mina platelet pellets was measured by Archimedes’ method (ASTM C373). The morphology of powders and the mi￾crostructure of composites were investigated by scanning electron microscopy (SEM, Model S-4700, Hitachi, Osaka, Japan). The composite pellets for SEM were polished down to a 1
m using diamond paste finish, and then thermally etched at 1550 ◦C for 30 min. A mixture of Elvax 210, 220, and 250 ethylene vinyl ac￾etate copolymers (Dupont, Wilmington, DEL) was used as binder phases. The molecular weight increased from Elvax 210, 220 to 250. The reason for using the mixture was to facilitate the binder removal process over a broad temper￾ature range. Dibutyl phthalate (Aldrich, 99%) and stearic acid (Aldrich, 95%) were used as a plasticizer and lubricant, respectively. Ceramic powder, binder, plasticizer, and lubricant were mixed in a computer controlled, high shear mixer (Model 2100, C. W. Brabender, NJ). The mixing formulation is shown in Table 1. To make the fibrous monolithic texture, without intermixing between inner mullite matrix and AlPO4 Fig. 1. The stainless steel mouldings (a) and extrusion (b) dies

D-K. Kim, W.M. Riven/Materials Science and Engineering 4 380(2004)237-244 239 interphase layer during extrusion, the viscosity of the inner mullite and interphase AlPO4 in the"green"monofilament layer should be higher than that of interphase material, and rod was 1.1l-1. 93 Monofilament rods are arranged in the so more powder was put into the matrix rod formulation to cylindrical die and extruded again into a die with a 2 mm di- increase the viscosity. In the case of the mullite and 50 vol. ameter orifice. This was referred to as the second extrusion alumina: 50 vol. YAG in situ composite, for the inner ma- and the extrudate was called a"multifilament rod trix rod, the powder loading was 52 vol % and plasticizer The multifilament rods were cut into 47mm length and lubricant were not used to obtain a higher viscosity. Fifty-five multifilament rods were arranged into a rectan- 4O vol. of powder loading was used for the AlPO4 and gular die and warm pressed at 150C, under a pressure of alumina platelet interphases 345MPa. The binder was then removed from the pressed The Brabender mixing temperature was 150C. The mix- pellet. The schedule for the binder removal was as follow ing torque of the formula tion was measured by reading the from 25 to 250C at a ramp rate of 0.05C/min, from 250 shear force between two mixing blades. The inner rod was to 450C at a ramp rate of 0. 1C/min, from 450 to 650C extruded at a rate of 50 mm/min into a cylindrical shape. The at a ramp rate of 0.3C/min, maintained at 650C for 2h, interphase formulation was warm pressed into a half tubular and subsequently cooled down to room temperature at a shape with the aid of a thickness controllable die at 150C, ramp rate of 0.5C/min. The binder-free body was ClPed at under an applied pressure of about 34.5 MPa. Photographs 413.7 MPa and then sintered at conditions of 1600C/10h of the molding and extrusion die are seen in Fig. 1. The and 1650 C/10 h for the mullite-AlPO4 and 50 vol. alu- center rod and half-tubular shape were arranged into a con- mina: 50 vol. YAG in situ composite matrix-alumina centric, cylindrical die of 23 mm total diameter by 150 mm platelet body, respectively length, and extruded into the die with a 2.0mm diameter The microstructures of monofilament rods. multifilament orifice. This was referred to as the first extrusion and the ex- rods, and green bodies were studied by optical microscopy trudate was called a"monofilament rod" having a two-layer (Model SMZ-2T, Nikon, Tokyo, Japan). The binder re texture. The ratio of relative volumetric amounts of inner moval behavior of the mullite-AlPO4, fibrous monolithic composite, was studied by thermogravimetry. (Model 7, 10 microns 10 microns Fig. 2. SEM micrographs of the matrix powders. (a) Mullite powder and (b)50 vol. alumina: 50 vol. YAG in situ composite(after I h attrition Fig 3 SEM micrographs of the interphase powders(after I h attrition milling).(a) Alumina platelets and(b)aluminum phosphate (AlPO4)

D.-K. Kim, W.M. Kriven / Materials Science and Engineering A 380 (2004) 237–244 239 interphase layer during extrusion, the viscosity of the inner layer should be higher than that of interphase material, and so more powder was put into the matrix rod formulation to increase the viscosity. In the case of the mullite and 50 vol.% alumina:50 vol.% YAG in situ composite, for the inner ma￾trix rod, the powder loading was 52 vol.%, and plasticizer and lubricant were not used to obtain a higher viscosity. 40 vol.% of powder loading was used for the AlPO4 and alumina platelet interphases. The Brabender mixing temperature was 150 ◦C. The mix￾ing torque of the formulation was measured by reading the shear force between two mixing blades. The inner rod was extruded at a rate of 50 mm/min into a cylindrical shape. The interphase formulation was warm pressed into a half tubular shape with the aid of a thickness controllable die at 150 ◦C, under an applied pressure of about 34.5 MPa. Photographs of the molding and extrusion die are seen in Fig. 1. The center rod and half-tubular shape were arranged into a con￾centric, cylindrical die of 23 mm total diameter by 150 mm length, and extruded into the die with a 2.0 mm diameter orifice. This was referred to as the first extrusion and the ex￾trudate was called a “monofilament rod” having a two-layer texture. The ratio of relative volumetric amounts of inner Fig. 2. SEM micrographs of the matrix powders. (a) Mullite powder and (b) 50 vol.% alumina:50 vol.% YAG in situ composite (after 1 h attrition milling). mullite and interphase AlPO4 in the “green” monofilament rod was 1.11–1. 93. Monofilament rods are arranged in the cylindrical die and extruded again into a die with a 2 mm di￾ameter orifice. This was referred to as the second extrusion and the extrudate was called a “multifilament rod”. The multifilament rods were cut into 47 mm lengths. Fifty-five multifilament rods were arranged into a rectan￾gular die and warm pressed at 150 ◦C, under a pressure of 34.5 MPa. The binder was then removed from the pressed pellet. The schedule for the binder removal was as follows: from 25 to 250 ◦C at a ramp rate of 0.05 ◦C/min, from 250 to 450 ◦C at a ramp rate of 0.1 ◦C/min, from 450 to 650 ◦C at a ramp rate of 0.3 ◦C/min, maintained at 650 ◦C for 2 h, and subsequently cooled down to room temperature at a ramp rate of 0.5 ◦C/min. The binder-free body was CIPed at 413.7 MPa and then sintered at conditions of 1600 ◦C/10 h and 1650 ◦C/10 h for the mullite-AlPO4 and 50 vol.% alu￾mina:50 vol.% YAG in situ composite matrix–alumina platelet body, respectively. The microstructures of monofilament rods, multifilament rods, and green bodies were studied by optical microscopy (Model SMZ-2T, Nikon, Tokyo, Japan). The binder re￾moval behavior of the mullite-AlPO4, fibrous monolithic composite, was studied by thermogravimetry. (Model 7, Fig. 3. SEM micrographs of the interphase powders (after 1 h attrition milling). (a) Alumina platelets and (b) aluminum phosphate (AlPO4)

D-K. Kim, W.M. Kriven/Materials Science and Engineering 4 380 (2004)237-244 3. Results and discussion Inner mullite layer SEM micrographs of the mullite and the 50 vol. alu mina: 50 vol. YAG in situ composite matrix powders are seen in Fig. 2. The mullite powder had a granular morphol- ogy, with an average particle size and surface area of 0.8 um and 8.5m-/g, respectively. The in situ alumina-YAG com- posite powder showed an irregular shape with sharp edges and it had a specific surface area of 2.7 m/g after I h attri- tion milling. Alumina platelets had a hexagonal plate shape Outer AlPo. layer of 5-10 um diameter, and I um thickness with a specific surface area of 1. 4m/g(Fig 3(a). An alumina platelet pel let CIPped at 413.7 MPa and then sintered at 1600C 20125130135140145150155160 3h, had a density of 80% of theoretical density and a 3-point bend strength of 205 7 MPa. This bending strength was Temperature (C) much higher than 1.5+0.2 MPa of AlPO4 [30]. This means Fig. 4. The variation of mixing torques with temperature for the mullite that alumina platelets can possibly function as a stronger inner rod and AlPO4 interphase layer. debonding material, resulting in a higher strength and tough- ness composite material. AlPO4 powder had an irregular shape with sharp edges(Fig. 3(b)). The I h attrition-milled AlPO4 powder had a particle size and specific surface area Connecticut, USA). The temperature ranged of 0.9 um and 87 m2/g, respectively emperature to 900C, and the heating rate The variations of the mixing torque for the mullite in- was Flexural strengths were measured with a ner matrix rod and AlPO4 interphase layer are plotted in testing machine(Model 4502, Instron Corp, Fig 4. To prevent intermixing between the inner matrix layer Canton, MA) in 3-point bending. The samples were cut and interphase layer during extrusion and, finally, to obtain from sintered pellets where the length of the testing sample a fibrous monolithic texture after extrusion, the viscosity was aligned with the longitudinal direction of the filaments. of the inner layer should be higher than that of the inter- The samples were ground with diamond paste and finally phase region. Fig. 4 shows that the inner layer had about polished with 600 grit SiC paper, after which the four edges a five-times higher mixing torque than did the aluminum of each sample were bevelled. The flexural strengths were phosphate, interphase layer. This means that the viscosity determined after testing 3-5 samples The supporting span requirement to obtain fibrous monolithic composite texture 30mm, the cross head speed was 0. I mm/min and was well satisfied for the formulations in Table 1. The mixing sample size was3mm(H)×4mm(W)×40mm(L torque decreased with increasing temperature. The binder Temperature ( C) Fig. 5. The binder burnout TGa profile from room temperature to 900C, for the mullite-AlPO4 two-layer, fibrous monolithic composite

240 D.-K. Kim, W.M. Kriven / Materials Science and Engineering A 380 (2004) 237–244 Fig. 4. The variation of mixing torques with temperature for the mullite inner rod and AlPO4 interphase layer. Perkin Elmer, Connecticut, USA). The temperature ranged from room temperature to 900 ◦C, and the heating rate was 5 ◦C/min. Flexural strengths were measured with a screw-driven testing machine (Model 4502, Instron Corp., Canton, MA) in 3-point bending. The samples were cut from sintered pellets where the length of the testing sample was aligned with the longitudinal direction of the filaments. The samples were ground with diamond paste and finally polished with 600 grit SiC paper, after which the four edges of each sample were bevelled. The flexural strengths were determined after testing 3–5 samples The supporting span was 30 mm, the cross head speed was 0.1 mm/min and sample size was 3 mm (H) × 4 mm (W) × 40 mm (L). Fig. 5. The binder burnout TGA profile from room temperature to 900 ◦C, for the mullite-AlPO4 two-layer, fibrous monolithic composite. 3. Results and discussion SEM micrographs of the mullite and the 50 vol.% alu￾mina:50 vol.% YAG in situ composite matrix powders are seen in Fig. 2. The mullite powder had a granular morphol￾ogy, with an average particle size and surface area of 0.8
m and 8.5 m2/g, respectively. The in situ alumina-YAG com￾posite powder showed an irregular shape with sharp edges and it had a specific surface area of 2.7 m2/g after 1 h attri￾tion milling. Alumina platelets had a hexagonal plate shape of 5–10
m diameter, and 1
m thickness with a specific surface area of 1.4 m2/g (Fig. 3(a)). An alumina platelet pel￾let CIPped at 413.7 MPa and then sintered at 1600 ◦C for 3 h, had a density of 80% of theoretical density and a 3-point bend strength of 205 ± 7 MPa. This bending strength was much higher than 1.5 ± 0.2 MPa of AlPO4 [30]. This means that alumina platelets can possibly function as a stronger debonding material, resulting in a higher strength and tough￾ness composite material. AlPO4 powder had an irregular shape with sharp edges (Fig. 3(b)). The 1 h attrition-milled AlPO4 powder had a particle size and specific surface area of 0.9
m and 87 m2/g, respectively. The variations of the mixing torque for the mullite in￾ner matrix rod and AlPO4 interphase layer are plotted in Fig. 4. To prevent intermixing between the inner matrix layer and interphase layer during extrusion and, finally, to obtain a fibrous monolithic texture after extrusion, the viscosity of the inner layer should be higher than that of the inter￾phase region. Fig. 4 shows that the inner layer had about a five-times higher mixing torque than did the aluminum phosphate, interphase layer. This means that the viscosity requirement to obtain fibrous monolithic composite texture was well satisfied for the formulations in Table 1. The mixing torque decreased with increasing temperature. The binder

D-K. Kim, W.M. Riven/Materials Science and Engineering 4 380(2004)237-244 M cm 1 mm (a) Imm 1 mm Fig. 6. Optical micrographs of the mullite-AlPO4, two-layer, fibrous mono- lithic composite, after binder removal. The fibrous monoliths were laid up into a rectangular sample for subsequent sectioning into bend tes Fig. 7. Optical micrographs of specimens filaments(M: matrix center rod (mullite), 1: interphase layer (AIPO4). The thickness of green interphase layer is 0.33 mm).(a) Monofil- ament rod and(b) multifilament rod. removal from the mullite-AlPO4 green pellet was studied by TGA. The results are presented in Fig. 5. The weight loss from room temperature to 900C consisted roughly of 5step:25-70,70-160,160-305,305-430,430-570,and 570-900C. This indicates how the binder was removed gradually over a wide temperature range. Fig. 6(a)is an optical micrograph of binder-free rectangular pellets and ig. 6(b) is the enlarged view of the surface. The sam- ple surface was clean and had no distortion after binder removal Fig. 7(a and b) are optical micrographs of green bod- ies of a monofilament rod and multifilament rod of the mullite-AlPO4 laminated composite. The interphase is dis- uished from th g aye The thickness of the AlPO4 interphase layer was 0.33 mm.A mm multifilament rod with diameter 2. 1 mm had approximately 93 two-layer, sub-cells in it. The microstructure of a green body of the two-layer, mullite-AlPO4 fibrous monolithic Fig. 8. Optical micrograph of the mullite-AlPO4 fibrous monolithic com- composite is shown in the optical micrograph of Fig. 8. The posite green body

D.-K. Kim, W.M. Kriven / Materials Science and Engineering A 380 (2004) 237–244 241 Fig. 6. Optical micrographs of the mullite-AlPO4, two-layer, fibrous mono￾lithic composite, after binder removal. The fibrous monoliths were laid up into a rectangular sample for subsequent sectioning into bend test specimens. removal from the mullite-AlPO4 green pellet was studied by TGA. The results are presented in Fig. 5. The weight loss from room temperature to 900 ◦C consisted roughly of 5 steps: 25–70, 70–160, 160–305, 305–430, 430–570, and 570–900 ◦C. This indicates how the binder was removed gradually over a wide temperature range. Fig. 6(a) is an optical micrograph of binder-free rectangular pellets and Fig. 6(b) is the enlarged view of the surface. The sam￾ple surface was clean and had no distortion after binder removal. Fig. 7(a and b) are optical micrographs of green bod￾ies of a monofilament rod and multifilament rod of the mullite-AlPO4 laminated composite. The interphase is dis￾tinguished from the matrix phase by a food coloring dye. The thickness of the AlPO4 interphase layer was 0.33 mm. A multifilament rod with diameter 2.1 mm had approximately 93 two-layer, sub-cells in it. The microstructure of a green body of the two-layer, mullite-AlPO4 fibrous monolithic composite is shown in the optical micrograph of Fig. 8. The Fig. 7. Optical micrographs of the mullite-AlPO4 fibrous monolithic composite filaments (M: matrix center rod (mullite), I: interphase layer (AlPO4). The thickness of green interphase layer is 0.33 mm). (a) Monofil￾ament rod and (b) multifilament rod. Fig. 8. Optical micrograph of the mullite-AlPO4 fibrous monolithic com￾posite green body

D-K. Kim, W.M. Kriven/Materials Science and Engineering 4 380 (2004)237-244 500 microns 25 500 microns M少 Fig 9. SEM micrographs of the sintered mullite-AlPO4, two-layer, fibrous monolithic composite (M: matrix center rod (mullite), 1: porous interpha Fig. 10. SEM micrographs of the sintered 50 vol. alumina: 50 vol.% layer(AlPO4)). mullite matrix and AlPO4 interphase formed a homogeneous and uniform microstructure Fig. 9(a and b)are SEM micrographs of the sintered mullite-AlPO4, two-layer, fibrous monolithic composite The two composites were mechanically evaluated by The microstructure is homogeneous, and the higher mag- 3-point bend testing and the load versus displacement nification image confirms that the AlPO4 interphase layer curves are given in Fig. 11. The two-layer, mullite-AlPO was porous. SEM micrograph of the sintered 50 vol. fibrous monolithic composite exhibited apparent non-brittle alumina: 50 vol. YAG in situ composite matrix-alumina fracture behavior with 0. 1 mm of displacement, and had platelet; fibrous monolithic composite are presented in a strength and work of fracture of 76+ 5 MPa and 0.45 Fig 10. The higher magnification micrograph of the inter- t 0.02 kJ/m, respectively. The graceful failure of the phase region, however, indicates that alumina platelets in mullite-AlPO4 composite, is attributed to crack deflection the layer had sintered together. Because of the high CIP- along the porous AlPO4 interphase as can be seen in Fig 12 ping pressure of 413. 7 MPa, the platelets in the interphase This SEM micrograph clearly shows that crack deflected region were thought to be compacted together without along the weak AlPO4 interphase On the other hand, the forming a porous pocket structure, which is necessary sintered 50 vol. alumina: 50 vol. YAG in situ composite for debonding to occur. Because the platelets were com- matrix-alumina platelet, two-layer fibrous monolithic com- pacted together after CIPping and the composite pellet was posite underwent brittle fracture, showing a displacement sintered at 1650C for 15h, the alumina platelets grains less than 0.02 mm, and had a room temperature, 3-point grew to about 2-3 times larger compared to their starting bend strength and work of fracture of 219 t 7 MPa and sizes 0. 25+ 0.03 kJ/m, respectively. The reason for the brittle

242 D.-K. Kim, W.M. Kriven / Materials Science and Engineering A 380 (2004) 237–244 Fig. 9. SEM micrographs of the sintered mullite-AlPO4, two-layer, fibrous monolithic composite. (M: matrix center rod (mullite), I: porous interphase layer (AlPO4)). mullite matrix and AlPO4 interphase formed a homogeneous and uniform microstructure. Fig. 9(a and b) are SEM micrographs of the sintered mullite-AlPO4, two-layer, fibrous monolithic composite. The microstructure is homogeneous, and the higher mag￾nification image confirms that the AlPO4 interphase layer was porous. SEM micrograph of the sintered 50 vol.% alumina:50 vol.% YAG in situ composite matrix–alumina platelet; fibrous monolithic composite are presented in Fig. 10. The higher magnification micrograph of the inter￾phase region, however, indicates that alumina platelets in the layer had sintered together. Because of the high CIP￾ping pressure of 413.7 MPa, the platelets in the interphase region were thought to be compacted together without forming a porous pocket structure, which is necessary for debonding to occur. Because the platelets were com￾pacted together after CIPping and the composite pellet was sintered at 1650 ◦C for 15 h, the alumina platelets grains grew to about 2–3 times larger compared to their starting sizes. Fig. 10. SEM micrographs of the sintered 50 vol.% alumina:50 vol.% YAG in situ composite matrix–alumina platelet interphase, forming a two-layer fibrous monolithic composite. (M: matrix center rod (50 vol.% alumina:50 vol.% YAG in situ composite), I: interphase layer (alumina platelets)). The two composites were mechanically evaluated by 3-point bend testing and the load versus displacement curves are given in Fig. 11. The two-layer, mullite-AlPO4 fibrous monolithic composite exhibited apparent non-brittle fracture behavior with ∼0.1 mm of displacement, and had a strength and work of fracture of 76 ± 5 MPa and 0.45 ± 0.02 kJ/m2, respectively. The graceful failure of the mullite-AlPO4 composite, is attributed to crack deflection along the porous AlPO4 interphase as can be seen in Fig. 12. This SEM micrograph clearly shows that crack deflected along the weak AlPO4 interphase. On the other hand, the sintered 50 vol.% alumina:50 vol.% YAG in situ composite matrix–alumina platelet, two-layer fibrous monolithic com￾posite underwent brittle fracture, showing a displacement less than 0.02 mm, and had a room temperature, 3-point bend strength and work of fracture of 219 ± 7 MPa and 0.25 ± 0.03 kJ/m2, respectively. The reason for the brittle

D-K. Kim, W.M. Riven/Materials Science and Engineering 4 380(2004)237-244 50 vol% A1Oj 0. 15+ ii in situ composite-alumina platelet Mullite-AiPO4 500 microns 0.020.040.060060.1 Displacement (mm) urves, for the bend tested, mullite-AlPOA and 50vol. alumina: 50 vol, % YAG in situ matrix-alumina platelet, fibrous monolithic composites fracture of this composite, can be attributed to the relatively dense microstructure of the alumina platelet interphase re- gion because of the compaction of platelets due to high CIPping pressure and sintering the pellet at high tempera- ture and for a long time at 1650C for 10 h, as can be seen in Fig. 10. The reasons for the relatively lower composite 2054 500 microns strength of 219 t 7 MPa are attributed to the grain growth of alumina platelets in the interphase region Fig. 13. SEM micrographs of the fracture surfaces of the two-layer fibrous Fig. 13 shows the fracture surfaces of two composites after 3-point bend testing. The mullite-AlPO4 fibrous monolithic alumina: 50 vol. YAG in situ composite pe and(b)50 vol% monolithic composites. (a) Mullite-AlPO4 composit composite indicated extensive fiber pull-out and a rough fracture surface. However the 50 vol. alumina: 50 vol% YAG in situ composite matrix-alumina platelet, two-layer fi- brous monolithic composite showed very little fiber pull-out 4. Conclusions and relatively smooth fracture surface Processing procedures for a mullite-AlPO4 and 50 vol% alumina: 50 vol. YAG in situ composite matrix-alumina platelet, two-layer fibrous monolithic composite were successfully demonstrated. The synthesized 50 vol. alu- mina: 50 vol. YAG in situ composite and AlPO4 powders had irregular shapes with sharp edges. The fact that the mixing torque value of the mullite inner matrix rod was about five-times higher than that of the outer aluminum phosphate interphase layer, indicated that the formulation M systems using graded ethylene vinylacetate copolymer as a binder, were good to make homogeneous fibrous monolithi composite texture without intermixing of two materials TGA analysis of mullite-AlPO4, two-layer green pellet, indicated that a multi-step binder removal was successful The 50 vol. alumina: 50 vol %YAG in situ matrix-alumina platelet, fibrous monolithic composite, exhibited brittle of significant densification in the alu platelet interphase during CIPping and sintering. The porous Fig. 12. SEM micrograph of the fractured mullite-AlPO4 fibrous mono. AlPO4 interphase layer allowed the mullite-AIPOA fibrous lithic composite monolith composite to show some non-brittle fracture

D.-K. Kim, W.M. Kriven / Materials Science and Engineering A 380 (2004) 237–244 243 Fig. 11. Stress–strain curves, for the bend tested, mullite-AlPO4 and 50 vol.% alumina:50 vol.% YAG in situ matrix–alumina platelet, fibrous monolithic composites. fracture of this composite, can be attributed to the relatively dense microstructure of the alumina platelet interphase re￾gion because of the compaction of platelets due to high CIPping pressure and sintering the pellet at high tempera￾ture and for a long time at 1650 ◦C for 10 h, as can be seen in Fig. 10. The reasons for the relatively lower composite strength of 219 ± 7 MPa are attributed to the grain growth of alumina platelets in the interphase region. Fig. 13 shows the fracture surfaces of two composites after 3-point bend testing. The mullite-AlPO4 fibrous monolithic composite indicated extensive fiber pull-out and a rough fracture surface. However the 50 vol.% alumina:50 vol.% YAG in situ composite matrix–alumina platelet, two-layer fi- brous monolithic composite showed very little fiber pull-out and relatively smooth fracture surface. Fig. 12. SEM micrograph of the fractured mullite-AlPO4 fibrous mono￾lithic composite. Fig. 13. SEM micrographs of the fracture surfaces of the two-layer fibrous monolithic composites. (a) Mullite-AlPO4 composite and (b) 50 vol.% alumina:50 vol.% YAG in situ composite-alumina platelet composite. 4. Conclusions Processing procedures for a mullite-AlPO4 and 50 vol.% alumina:50 vol.% YAG in situ composite matrix–alumina platelet, two-layer fibrous monolithic composite were successfully demonstrated. The synthesized 50 vol.% alu￾mina:50 vol.% YAG in situ composite and AlPO4 powders had irregular shapes with sharp edges. The fact that the mixing torque value of the mullite inner matrix rod was about five-times higher than that of the outer aluminum phosphate interphase layer, indicated that the formulation systems using graded ethylene vinylacetate copolymer as a binder, were good to make homogeneous fibrous monolithic composite texture without intermixing of two materials. TGA analysis of mullite-AlPO4, two-layer green pellet, indicated that a multi-step binder removal was successful. The 50 vol.% alumina:50 vol.% YAG in situ matrix–alumina platelet, fibrous monolithic composite, exhibited brittle fracture, because of significant densification in the alumina platelet interphase during CIPping and sintering. The porous AlPO4 interphase layer allowed the mullite-AlPO4 fibrous monolith composite to show some non-brittle fracture

D-K. Kim, W.M. Kriven/Materials Science and Engineering 4 380 (2004)237-244 Acknowledgements [15 Y Okamoto, H Fukudome, K Hayashi, T Nishikawa, J. Eur. Ceram. Soc.6(1990)161-168. This work was supported by the US AFOSR under grant [6]S. Kanzaki,HTabata, T.Kumazawa,S.Ohta, J.Am. CeramSoc number:F49620-03-1-0082 68(1)(1985)C6-C7 17] M. Mizuno, J. Am. Ceram Soc. 74(1991)3017-3022 18T Kumazawa, S Kanzaki, S. Ohta, H. Tabata, J Ceram Soc. Jpn. 96(1)(1988)85 References 19P.A. Lessing, R.s. Gordon, K.S. Mazdiyasni, J. Am. Ceram. S 58(3-4)(1975)149 20]K Keller, T Mah, T.A. Parthasarathy, Ceram. Eng. l w.J. Clegg, K. Kendall, N.M. Alford, T.W. Button, J D 1990)1122-1133 ure347(4)(1990)455-457 21T. Mah, M.G. Mendiratta, L.A. Boothe, High Te 2] T. Shannon, S. Blackburn, Ceram. Eng. Sci. Proc. 16(5-6)( of Refractory Oxide-Oxide Composites, U.S. Air Force Report 1115-1120. AFWAL-TR-88-4015, April 1988 3] D.H. Kuo, W.M. Kriven, Mater. Sci. Eng. A 210(1996)123-134 22]RS Hay, L E Matson, Acta Metall. Mater. 39(8)(1991)1981-1994. 14 T. Chartier, D. Merle, J. L. Besson, J. Eur. Ceram 15(1995)(23]T. Mah, T.A. Parthasarathy, L.E. Matson, Ceram. Eng. Sci. Proc. 9-10)(1990)1617-1627 []DH Kuo, W.M. Kriven, J. Am. Ceram Soc. 80(9)(1997)2421-[24] D. Viechinicki, F. Schmid, J Mater. Sci. 4(1969)84-88 2424 25Y. Waku, N. Nakagawa, T. Wakamoto, H. Ohtsubo, K. Shimizu, Y 6 G.J. Zhang, X M. Yue, T. Watanabe, J. Am. Ceram. Soc. 82(11) Kohtoku, J. Mater. Sci. 33(1998)1217-1225 (19993257-3259 26Y. Waku, H Ohtsubo, N. Nakagawa, Y. Kohtoku, J. Mater. Sci. 31 [7 w.s. Coblenz, Fibrous Monolithic Ceramic and Method for Produc- (1996)4663-4670 tion, US Patent No. 4772524, 20 September 1988 27]Y. Waku, N Nakagawa, H Ohtsubo, Y. Ohsora, Y. Kohtoku, J. Japan [8]S. Baskaran, S.D. Nunn, D. Popovic, J.W. Halloran, J Am Ceram inst.Met.59(1)(195)71-78 Soc.76(9)(1993)2209-2216 28Y. Waku, N. Nakagawa, T. Wakamoto, H Ohtsubo, K. Shimizu,Y. [9]S Baskaran, J.W. Halloran, J. Am. Ceram. Sc. 76(9)(1993)2217- Kohtoku, J. Mater. Sci. 33(1998)4943-49 29]D K. Kim, W.M. Kriven, J. Am. Ceram Soc., in press. [10S. Baskaran, J W. Halloran, J Am Ceram Soc. 77(5)(1994)1249- [30 D K. Kim, W.M. Kriven, J. Am. Ceram Soc. 86(11)(2003)1962- [1]. Baskaran, J.W. Halloran, Ceram. Eng. Sci. Proc. 14(9-10)(1993 31S.J. Lee, W.M. Kriven, J. Am. Ceram. Soc. 84 (4)(2001)767-774 813-823 32]MA Gulgun, W.M. Kriven, Ceram. Trans. 62(1995)57-66 [12] H Ohnishi, K. Maeda, T. Nakamura, T. Kawanami, in: S Somiya, 33]EA. Benson, S.J. Lee, W.M. Riven, J. Am. Ceram. Soc. 82(8 R F. Davis, J.A. Pask(Eds ) Ceramic Transactions, vol. 6, Mullite (1999)2049-2055 and Mullite Matrix Composites, American Ceramic Society, West- [34]SJ. Lee, W.M. Kriven, Ceram. Eng. Sci. Proc. 20(3)(1999)69-76. erville, Ohio, 1990, pp 605-612 65MH. Nguyen, S.J. Lee, W.M. Kriven, J. Mater Res. 14(8)(1999) [13] H Schneider, K. Okada, J.A. Pask, Mullite and Mullite Ceramics, 3417-3426 John Wiley, New York, 1994 36]WM. Riven, S.J. Lee, M.A. Gulgun, M.H. Nguyen, D K. Kim, [14 W.M. Kriven, J. Palko, S. Sinogeikin, J D. Bass, A. Sayir, G Cera. Trans.108(2000)99-110 Brunauer, H. Boysen, F. Frey, J. Schneider, J. Eur. Ceram. Soc 37M.A. Gulgun, W.M. Kriven, M.H. Nguyen, Processes for Preparing 19(13)(1999)25292541 Mixed-Oxide Powders. US Patent No. 6482387. 19 November 2002

244 D.-K. Kim, W.M. Kriven / Materials Science and Engineering A 380 (2004) 237–244 Acknowledgements This work was supported by the US AFOSR under grant number: F49620-03-1-0082. References [1] W.J. Clegg, K. Kendall, N.M. Alford, T.W. Button, J.D. Birchall, Nature 347 (4) (1990) 455–457. [2] T. Shannon, S. Blackburn, Ceram. Eng. Sci. Proc. 16 (5–6) (1995) 1115–1120. [3] D.H. Kuo, W.M. Kriven, Mater. Sci. Eng. A 210 (1996) 123–134. [4] T. Chartier, D. Merle, J.L. Besson, J. Eur. Ceram. Soc. 15 (1995) 101–107. [5] D.H. Kuo, W.M. Kriven, J. Am. Ceram. Soc. 80 (9) (1997) 2421– 2424. [6] G.J. Zhang, X.M. Yue, T. Watanabe, J. Am. Ceram. Soc. 82 (11) (1999) 3257–3259. [7] W.S. Coblenz, Fibrous Monolithic Ceramic and Method for Produc￾tion, US Patent No. 4772524, 20 September 1988. [8] S. Baskaran, S.D. Nunn, D. Popovic, J.W. Halloran, J. Am. Ceram. Soc. 76 (9) (1993) 2209–2216. [9] S. Baskaran, J.W. Halloran, J. Am. Ceram. Sc. 76 (9) (1993) 2217– 2224. [10] S. Baskaran, J.W. Halloran, J. Am. Ceram. Soc. 77 (5) (1994) 1249– 1255. [11] S. Baskaran, J.W. Halloran, Ceram. Eng. Sci. Proc. 14 (9–10) (1993) 813–823. [12] H. Ohnishi, K. Maeda, T. Nakamura, T. Kawanami, in: S. Somiya, R.F. Davis, J.A. Pask (Eds.), Ceramic Transactions, vol. 6, Mullite and Mullite Matrix Composites, American Ceramic Society, West￾erville, Ohio, 1990, pp. 605–612. [13] H. Schneider, K. Okada, J.A. Pask, Mullite and Mullite Ceramics, John Wiley, New York, 1994. [14] W.M. Kriven, J. Palko, S. Sinogeikin, J.D. Bass, A. Sayir, G. Brunauer, H. Boysen, F. Frey, J. Schneider, J. Eur. Ceram. Soc. 19 (13) (1999) 2529–2541. [15] Y. Okamoto, H. Fukudome, K. Hayashi, T. Nishikawa, J. Eur. Ceram. Soc. 6 (1990) 161–168. [16] S. Kanzaki, H. Tabata, T. Kumazawa, S. Ohta, J. Am. Ceram. Soc. 68 (1) (1985) C6–C7. [17] M. Mizuno, J. Am. Ceram. Soc. 74 (1991) 3017–3022. [18] T. Kumazawa, S. Kanzaki, S. Ohta, H. Tabata, J. Ceram. Soc. Jpn. 96 (1) (1988) 85. [19] P.A. Lessing, R.S. Gordon, K.S. Mazdiyasni, J. Am. Ceram. Soc. 58 (3–4) (1975) 149. [20] K. Keller, T. Mah, T.A. Parthasarathy, Ceram. Eng. Sci. Proc. 11 (7–8) (1990) 1122–1133. [21] T. Mah, M.G. Mendiratta, L.A. Boothe, High Temperature Stabil￾ity of Refractory Oxide–Oxide Composites, U.S. Air Force Report AFWAL-TR-88-4015, April 1988. [22] R.S. Hay, L.E. Matson, Acta Metall. Mater. 39 (8) (1991) 1981–1994. [23] T. Mah, T.A. Parthasarathy, L.E. Matson, Ceram. Eng. Sci. Proc. 11 (9–10) (1990) 1617–1627. [24] D. Viechinicki, F. Schmid, J. Mater. Sci. 4 (1969) 84–88. [25] Y. Waku, N. Nakagawa, T. Wakamoto, H. Ohtsubo, K. Shimizu, Y. Kohtoku, J. Mater. Sci. 33 (1998) 1217–1225. [26] Y. Waku, H. Ohtsubo, N. Nakagawa, Y. Kohtoku, J. Mater. Sci. 31 (1996) 4663–4670. [27] Y. Waku, N. Nakagawa, H. Ohtsubo, Y. Ohsora, Y. Kohtoku, J. Japan Inst. Met. 59 (1) (1995) 71–78. [28] Y. Waku, N. Nakagawa, T. Wakamoto, H. Ohtsubo, K. Shimizu, Y. Kohtoku, J. Mater. Sci. 33 (1998) 4943–4951. [29] D.K. Kim, W.M. Kriven, J. Am. Ceram. Soc., in press. [30] D.K. Kim, W.M. Kriven, J. Am. Ceram. Soc. 86 (11) (2003) 1962– 1964. [31] S.J. Lee, W.M. Kriven, J. Am. Ceram. Soc. 84 (4) (2001) 767–774. [32] M.A. Gülgün, W.M. Kriven, Ceram. Trans. 62 (1995) 57–66. [33] E.A. Benson, S.J. Lee, W.M. Kriven, J. Am. Ceram. Soc. 82 (8) (1999) 2049–2055. [34] S.J. Lee, W.M. Kriven, Ceram. Eng. Sci. Proc. 20 (3) (1999) 69–76. [35] M.H. Nguyen, S.J. Lee, W.M. Kriven, J. Mater. Res. 14 (8) (1999) 3417–3426. [36] W.M. Kriven, S.J. Lee, M.A. Gülgün, M.H. Nguyen, D.K. Kim, Ceram. Trans. 108 (2000) 99–110. [37] M.A. Gülgün, W.M. Kriven, M.H. Nguyen, Processes for Preparing Mixed-Oxide Powders, US Patent No. 6482387, 19 November 2002