LSEVIER Materials Science and Engineering: C3 (1995)125-130 Biomimicry of bamboo bast fiber with engineering composite materials S.H. Lia.b, * Q.Y. Zeng Y L. Xiao , S.Y. Fu.b,B L.Zh temational Center for Materials Physics, Academia Sinica, 72 Wenhua Road, Shenyang 110015, People's Republic of china b Institute of Meta! Research, Academia Sinica, 72 Wenhua Road, Shenyang 110015, People's Republic of chin c Institute of Applied Ecology, Academia Sinica, 72 Wenhua Road, Shenyang 110015, Peoples Republic of china bstract Bamboo, one of the strongest natural structural composite materials, has many distinguishing features. It has been found that its reinforcement unit, hollow, multilayered and spirally-wound bast fiber, plays an extremely important role in its mechanical behavior. In the present work, on the basis of the study on bamboo bast fiber and wood tracheid, a biomimetic model of the reinforcing element, composed of two layers of helically wound fiber, was suggested. To detect the structural characteristics of such a microstructure, four types of macro fiber specimens made of engineering composites were employed: axially aligned solid and hollow cylinders, and single-and double-helical hollow cylinders. These specimens were subjected to several possible loadings, and the experimental results reveal that only the double-helical structural unit possesses the optimum comprehensive mechanical properties. An interlaminar transition zone model imitating bamboo bast fiber was proposed nd was verified by engineering composite materials, In our work, the transition zone can increase the interlaminar shear strength of the composite materials by about 15%. These biomimetic structural models can be applied in the design and manufacture of engineering composite Keywords: Bamboo; Bast fiber; Biomimetics; Engineering composites I. Introduction Bamboo is another kind of common natural structural com- posite. It is a widespread plant family found in all continent Mankind has long had the idea that we should learn from Apart from being a basic material in the construction and nature. There are innumerable biological materials in nature paper industries, bamboo is a more typical long-fiber rein- at exhibit distinguishing performance. All biological mate- forced composite than wood. Thus, some biomimetic studies rials are, without exception, composites with the rapid devel- on bamboo have been carried out in recent years by Li et al opment of engineering composite materials in recent years, [5]. Earlier works vere prima ly focused on the macro and various problems were encountered in both the design and meso scales. From the results of the present work, it was fabrication process. To solve these newly emerging problem found that on a micro scale, bamboo has some unique features many measures were attempted. Among them, one interesting which are essentially important for the high performance of method became increasingly attractive; this new interdisci- bamb plinary subject is called biomimetics 1,2], the purpose of which is to advance man-made compositc materials through idance from nature. In the former biomimetic study, wood 2. Comparison of wood and bamboo as the most common natural composite, was noticed as early as 1980. Gordon and Jeronimidis extensively studied the tra. Wood is a natural composite that exhibits a remarka cheid of timber, and successfully applied the energy absorp- combination of strength, stiffness and toughness. Detailed tion mechanism of wood cells under tension in engineering studies have established that the unique hierarchical architec horough understanding of the interplay between the mor basis for achieving excellent properties. Besides wood, bar hology and structural performance of different types of boo has a gradient structure and excellent specific properties wood led to a remarkable development of a patented nev which are even comparable with ARALL [5]. The chemical material [4] composition of wood and bamboo [6] are listed in table 1 From Table 1 it can be seen that bamboo and wood have Corresponding author. very similar chemical components, but their mechanical 0928-4931/95/$09.50@ 1995 Elsevier Science S.A. All rights reserved SSDr0928-4931(95)0011s-8
ELSEVIER Biomimicry of’ bamboo bast fiber with engineering composite materials Materials Science and Engineering: C 3 (1995) 125-130 S.H. Li a,b,* , Q.Y. Zeng ‘, Y.L. Xiao a, S.Y. Fu a*b, B.L. Zhou a,b a International Centerfor Materials Physics, Academia Sinica, 72 Wenhua Road, Shenyang 110015, People’s Republic of China b Institute qf Metal Research, Academia Sinica, 72 Wenhua Road, Shenyang 110015, People’s Republic of China ‘Institute of Applied Ecology, Academia Sinica, 72 Wenhua Road, Shenyang llOOl5, People’s Republic of China Abstract Bamboo, one of the strongest natural structural composite materials, has many distinguishing features. It has been found that its reinforcement unit, hollow, multilayered and spirally-wound bast fiber, plays an extremely important role in its mechanical behavior. In the present work, on the basis of the study on bamboo bast fiber and wood tracheid, a biomimetic model of the reinforcing element, composed of two layers of helically wound fiber, was suggested. To detect the structural characteristics of such a microstructure, four types of macro fiber specimens made of engineering compositses were employed: axially aligned solid and hollow cylinders, and single- and double-helical hollow cylinders. These specimens were subjected to several possible loadings, and the experimental results reveal that only the double-helical structural unit possesses the optimum comprehensive mechanical properties. An interlaminar transition zone model imitating bamboo bast fiber was proposed and was verified by engineering composite materials. In our work, the transition zone can increase the interlaminar shear strength of the composite materials by about 15%. These biomimetic structural models can be applied in the design and manufacture of engineering composite materials. Keywords: Bamboo; Bast fiber; Biomimetics; Engineering composites 1. Introduction Mankind has long had the idea that we should learn from nature. There are innumerable biological materials in nature that exhibit distinguishing performance. All biological materials are, without exception, Icomposites. With therapiddevelopment of engineering composite materials in recent years, various problems were encountered in both the design and fabrication process. To solve these newly emerging problems, many measures were attempted. Among them, one interesting method became increasingly attractive; this new interdisciplinary subject is called biomimetics [ 1,2], the purpose of which is to advance man-made composite materials through guidance from nature. In the former biomimetic study, wood as the most common natural: composite, was noticed as early as 1980. Gordon and Jeronimidis extensively studied the tracheid of timber, and successfully applied the energy absorption mechanism of wood cells under tension in engineering composite materials to increase the work of fracture [ 31. The thorough understanding of the interplay between the morphology and structural performance of different types of wood led to a remarkable (development of a patented new material [ 41. * Corresponding author. 09284931/95/$09.50 0 1995 Elsevier Science S.A. All rights reserved SSDIO928-4931(95)00115-8 Bamboo is another kind of common natural structural composite. It is a widespread plant family found in all continents. Apart from being a basic material in the construction and paper industries, bamboo is a more typical long-fiber reinforced composite than wood. Thus, some biomimetic studies on bamboo have been carried out in recent years by Li et al. [ 51. Earlier works were primarily focused on the macro and meso scales. From the results of the present work, it was found that on a micro scale, bamboo has some unique features which are essentially important for the high performance of bamboo. 2. Comparison of wood and bamboo Wood is a natural composite that exhibits a remarkable combination of strength, stiffness and toughness. Detailed studies have established that the unique hierarchical architecture with which the constituents of wood are arranged is the basis for achieving excellent properties. Besides wood, bamboo has a gradient structure and excellent specific properties which are even comparable with ARALL@ [ 51. The chemical composition of wood and bamboo [ 61 are listed in Table 1. From Table 1 it can be seen that bamboo and wood have very similar chemical components, but their mechanical
S.H. Li et al. Materials Science and Engineering C 3(1995)125-130 Table 1 features of the reinforcing elements of biomaterials were Chemical composition and tensile strength of wood and bamboo taken into consideration and were experimentally investi Wood Bamboo [6 gated under all possible loading types. The modulus proper ties of bamboo bast fiber were reported in Ref. 181, and only Cellulose(%) Lignin(%) 353 the strength properties were focused on from Fig. I it can be seen that a bamboo fiber consists of alternating broad and thin concentric layers which are com Polyoses(%) Extractive(%) posed of microfibrils. The microfibril orientation angles in Tensile strength(MPa) 34-220 150-520 the broad layer are in the range 3-10 with respect to the fiber axis, and those in thin layers are in the range 30-90, but mostly 30-45. Although its microstructure is complicated we assume that a broad and a thin layer form a structural unit. Imitating such a structural unit, a biomimetic double-helical reinforcing element model, composed of a broad and a thin layer was proposed Corresponding to all the structural features mentioned L2 above, four types of macrofiber specimens were designed and manufactured in order to reveal the structural characteristics The material is glass fiber reinforced epoxy resin. Although these fiber specimens are on a macro scale, it is reasonable to treat them as the result of magnifying the microfibril and bamboo bast fiber in the same proportion, and hence the structural and mechanical features of the microscopic bast (b) fiber will still be maintained. The structures of the four types of macrofiber are shown in Fig. 2. Their structural forms are wall(O), broad layers listed in Table 2. The total fiber number and fiber volume Ll-L4), and narrow layers(NI-N3),(After Wai et al. [7].) fraction of each type of specimen were controlled to be the properties are very different. Their structural differences, parison of the test results meaningful. The properties tested from macro to micro scale, are responsible for this. On the nacro scale, wood is a solid cylinder while bamboo is a hollow cylinder with many nodes arranged longitudinally On the meso scale, wood is composed of alternative spring and summer wood but bamboo has a non-linear gradient structure which comprises vascular bundles and thin- walled cells. on the micro scale, wood tracheid and bamboo bast ber are both hollow tubes or cylinders composed of several oncentric layers and each layer is reinforced with helically wound microfibrils(or protofibrils). However, the differ ences in their cell wall thickness, layer number and microfi brillar angle are also obvious. In Fig. 1 the microstructures of a wood cell (a)and a bamboo fiber(b)[7] are shown 3. Biomimetic study of a double-helical reinforcing element model Fig. 2. Diagram of the structures of the four types of macrofiber specimens. the fibers axially aligned. (c)Hollow, single- helical cylinder. (d) Hollow, The common structural features of the reinforcingelements double-helical cylinder of plant materials can be expressed as being all hollow, hel- ders, or tubes. In pre Table 2 vious biomimetic research, only the hollow and helically Four types of macrofibers to verify the structural features of bamboo fibers wound features were noted and studied [3, 4], and the way A: Solid cylinder, its fibers are arranged along the axial direction f loading was only limited to tension. In fact, the reinforcing B: Hollow cylinder, its fibers are lements of living organisms are possibly subjected to other C: Hollow single-layered right-helical cylinder(15) kinds of loads, such as compression, bending, etc, even a D: Hollow double-layered helical cylinder(80% fibre inside in right helix, combined complicated load. In this work, all the structural 15: 20% fibre outside in left helix, 300)
126 S.H. Li et al. /Materials Science and Engineering: C 3 (1995) 125-130 Table 1 Chemical composition and tensile strength of wood and bamboo Wood Bamboo [6] Cellulose ( %) 40-50 45.3 Hemi-cell;lose (%) 20-35 Lignin (%) 15-35 25.5 Polyoses (%) 24.3 Extractive (I) < 10 2.6 Tensile strength ( MPa) 34-220 150-520 L4 N3 L3 N2 L2 NI LI 0 P Fig. 1. Schematic diagram of wood tracheid (a) and bamboo bast fiber (b) Primary wall (P), outermost layer of the second wall (0). broad layers (Ll-LA), and narrow layers (Nl-N3). (After Wai et al. [7].) properties are very different. Their structural differences, from macro to micro scale, are responsible for this. On the macro scale, wood is a solid cylinder, while bamboo is a hollow cylinder with many nodes arranged longitudinally. On the meso scale, wood is composed of alternative spring and summer wood, but bamboo has a non-linear gradient structure which comprises vascular bundles and thin-walled cells. On the micro scale, wood tracheid and bamboo bast fiber are both hollow tubes or cylinders composed of several concentric layers and each layer is reinforced with helically wound microfibrils (or protofibrils). However, the differences in their cell wall thickness, layer number and microfibrillar angle are also obvious. In Fig. 1 the microstructures of a wood cell (a) and a bamboo fiber (b) [7] are shown. 3. Biomimetic study of a double-helical reinforcing element model The common structural features of the reinforcing elements of plant materials can be expressed as being all hollow, helically wound and multi-layered cylinders, or tubes. In previous biomimetic research, only the hollow and helically wound features were noted and studied [3,4], and the way of loading was only limited to tension. In fact, the reinforcing elements of living organisms are possibly subjected to other kinds of loads, such as compression, bending, etc., even a combined complicated load. In this work; all the structural features of the reinforcing elements of biomaterials were taken into consideration and were experimentally investigated under all possible loading types. The modulus properties of bamboo bast fiber were reported in Ref. [ 81, and only the strength properties were focused on. From Fig. 1 it can be seen that a bamboo fiber consists of alternating broad and thin concentric layers which are composed of microfibrils. The microfibril orientation angles in the broad layer are in the range 3-10” with respect to the fiber axis, and those in thin layers are in the range 30-90”, but mostly 30-45”. Although its microstructure is complicated, we assume that a broad and a thin layer form a structural unit. Imitating such a structural unit, a biomimetic double-helical reinforcing element model, composed of a broad and a thin layer was proposed. Corresponding to all the structural features mentioned above, four types of macrofiber specimens were designed and manufactured in order to reveal the structural characteristics. The material is glass fiber reinforced epoxy resin. Although these fiber specimens are on a macro scale, it is reasonable to treat them as the result of magnifying the microfibril and bamboo bast fiber in the same proportion, and hence the structural and mechrinic&l features of the microscopic bast fiber will still be maintained. The structures of the four types of macrofiber are shown in Fig. 2. Their structural forms are listed in Table 2. The total fiber number and fiber volume fraction of each type of specimen were controlled to be the same in the manufacturing process in order to make the comparison of the test results meaningful. The properties tested (a) (b) (c) (d) Fig. 2. Diagram of the structures of the four types of macrofiber specimens. (a) Solid cylinder with the fibers axially aligned. (b) Hollow cylinder with the fibers axially aligned. (c) Hollow, single-helical cylinder. (d) Hollow, double-helical cylinder. Table 2 Four types of macrofibers to verify the structural features of bamboo fibers A: Solid cylinder, its fibers are arranged along the axial direction B: Hollow cylinder, its fibers am arranged axially C: Hollow single-layered right-helical cylinder (15”) D: Hollow double-layered helical cylinder (80% fibre inside in right helix, 15”; 20% fibre outside in left helix, 30”)
S.H. Li et aL. /Materials Science and Engineering: C 3(1995)125-130 Table 3 The properties tested and geometric size of the specimen(D and d are the outer and inner diameters of the macro fiber specimen, respectively Specimen length Specimen diameter Compressive buckling strength Three-point bending 230(span=190) B,C&D:D=14.7;d=5 Compressive strength Post-buckling compressive strength Tensile modulus and strength A:D=7.5 Gauge length=80 BC&D:D=8;d=2.8 ammary of the experimental results on the six mechanical properties of the four types of structures( the data in parentheses are standard deviations) C 494 38.9 (51) (74) (4.7) V=50% 825 (68) (14.1) (8.3) Compressive strength 1412 ( MPa) (84) (73) (59) 262.1 9.3 208.I (204) (29.9) (18.9) 5 Apparent fexural strengt 262.2 253.0 2539 (14.2) Post-buckling compressive (334) (174) Tensile modulus(GPa) 22.1 22.1 Tensile strength(MPa) 410.7 (24.6) nd the geometric size of the specimens are listed in Table 3. the central part and hence relative displacement occurs The mechanical properties tested and the experimental results between two oppositely arranged helical layers and the out are summarized in Table 4 side thin layer is more easily damaged. To determine the Natural bamboo bast fiber is so slender that its diameter extent of the damage caused by buckling, the post-buckling ranges between 20 um and 45 um and its length is 1000- compressive strength was tested and the results are also listed 2000 um. For a single fiber, the stability of such a structure in Table 4. From these data it is evident that buckling causes with a high length to diarneter ratio cannot be overlooked. more damage to double-helical structures than the other three compare the structural stability of the four types of specimens. tures can improve the structural shily D-type Thus the axial compressive buckling test was performed to types of structure. This is also the reason why D-type struc The testing speed was 2 mm min and the test was per- For the bending test, owing to the anisotropy and thick formed at room temperature. From the experimental data wall of the four types of specimens, the precise calculation listed in Table 4, it can be seen that the D-type specimen is of the maximum normal stress according to classical com- more stable than the C-type specimen but less than the B- posites theory is very complicated. Here the geometric sizes type, and shows no inferiority to the A type specimen. That fiber volume fraction and total number of fibers were con- is to say, double-helical structures will be more stable than trolled as seriously as possible in the manufacturing process single-helical ones, although only a thin layer of left-helical of the specimens so that a comparison of the maximum bend fibers was wound outside The inversely wound helical fiber ing load is meaningful. Furthermore, for the A-type speci lyers restrained each other when the specimen was com- men, its fibers were arranged along the axial direction, and essed. During the test for axial compressive buckling, an the deviation angle of the C-type specimen was 15. For the interesting phenomenon was observed. Of the four types of D-type specimen, there are only 20% of fibers whose helical specimens, only on the surface of the D-type specimen angle is 30, thus the relative anisotropy is not very strong. If obvious damage found after buckling. This can be explained the anisotropy of the specimen was not taken into account follows. When buckling occurs, the specimen will bend in the maximum normal stress, calculated according to the
S.H. Li et al. /Materials Science and Engineering: C 3 (1995) 125-130 127 Table 3 The properties tested and geometric size of the specimen (D and dare the outer and inner diameters of the macro fiber specimen, respectively) Properties tested Compressive buckling strength Three-point bending Compressive strength Post-buckling compressive strength Tensile modulus and strength Specimen length (mm) 300 230 (span= 190) 30 20 210 Gauge length = 80 Specimen diameter (mm) A: D= 13.8 B,C&D: 0=14.7;d=5 A: D=7.5 B,C&D:D=8;d=2.8 Table 4 A summary of the experimental :results on the six mechanical properties of the four types of structures (the data in parentheses are standard deviations) No. of samples A B C D Compressive buckling strength ( MPa) Compressive strength (MPa) Apparent flexural strength (MPa) Post-buckling compressive strength (MPa) Tensile mo,dulus ( GPa) Tensile strength ( MPa) Vr=40% 49.4 - 38.9 49.4 (5.1) (7.4) (4.7) v,= 50% 63.9 89.5 53.1 82.5 (6.8) (14.1) (8.3). (5.9) V,=40% 138.1 - 128.5 141.2 (8.4) (7.3) (5.9) v*= 50% 201.1 262.1 199.3 208.1 (20.4) (29.9) (24.1) (18.9) 251.7 262.2 253.0 253.9 (14.2) (21.8) (19.2) (16.1) 207.5 213.0 180.6 176.8 (32.2) (29.1) (33.4) (17.4) 25.6 22.1 22.1 (2.2) (1.8) (1.4) 410.7 373.9 401.3 (24.6) (16.2) (21.2) and the geometric size of the specimens are listed in Table 3. The mechanical properties tested and the experimental results are summarized in Table 4. Natural bamboo bast fiber is so slender that its diameter ranges between 20 pm and 45 pm and its length is lOOO- 2000 pm. For a single fiber, the stability of such a structure with a high length to diameter ratio cannot be overlooked. Thus the axial compressive buckling test was performed to compare the structural stability of the four types of specimens. The testing speed was 2 mm min-’ and the test was performed at room temperature. From the experimental data listed in Table 4, it can be seen that the D-type specimen is more stable than the C-type specimen but less than the Btype, and shows no inferiority to the A-type specimen. That is to say, double-helical structures will be more stable than single-helical ones, although only a thin layer of left-helical fibers was wound outside. The inversely wound helical fiber layers restrained each other when the specimen was compressed During the test for axial compressive buckling, an interesting phenomenon was observed. Of the four types of specimens, only on the surface of the D-type specimen was obvious damage found after buckling. This can be explained as follows. When buckling occurs, the specimen will bend in the central part and hence relative displacement occurs between two oppositely arranged helical layers and the outside thin layer is more easily damaged. To determine the extent of the damage caused by buckling, the post-buckling compressive strength was tested and the results are also listed in Table 4. From these data it is evident that buckling causes more damage to double-helical structures than the other three types of structure. This is also the reason why D-type structures can improve the structural stability. For the bending test, owing to the anisotropy and thick wall of the four types of specimens, the precise calculation of the maximum normal stress according to classical composites theory is very complicated. Here the geometric sizes, fiber volume fraction and total number of fibers were controlled as seriously as possible in the manufacturing process of the specimens so that a comparison of the maximum bending load is meaningful. Furthermore, for the A-type specimen, its fibers were arranged along the axial direction, and the deviation angle of the C-type specimen was. 1.5”. For the D-type specimen, there are only 20% of fibers whose helical angle is 30”, thus the relative anisotropy is not very strong. If the anisotropy of the specimen was not taken into account, the maximum normal stress, calculated according to the
S.H. Liet al / Materials Science and Engineering: C 3(1995)125-130 40 15 10 3 Displac。mnt(mm) Displacement (mm) Fig 3. Typical curve of the D-type specimen under compressive load Fig 4 Load-displacement curve of the type-C specimen under tension mechanics of the materials, can give a rough comparison of number of them, perhaps about 10%, do. This phenomenon the maximum normal stress. This can be called the'apparent was then applied in engineering composite materials and the flexural strength, a parameter of the relative capacity to bear work of fracture was increased successfully at the expense of ending load, From the calculated rcsults listed in Table 4 a moderate loss of stiffness and axial strength [3] it can be seen that the d-type specimens show no inferiority In our tension experiment, the so-called pseudo-plasticity to the other types of structure in bearing the bending load For the compressive test, the load-displacement curve of although not as obvious as reported in Ref [3] for the long e D-type specimen is much different from those of the spirally wound tube. The fiber fully aligned A-type specimens others. Its typical curve is shown in Fig 3. If only from the fracture abruptly after the maximum load. This can wpoint of compressive strength, the D-type structure is explained as follows. According to the buckling theory of closer to the a type but is better than the c-type structure composite materials, the critical buckling stress is a function However, if the pseudo-plastic phenomenon which occurred of the principal elastic constants of the tube, the angle of the in the D-type specimen is considered, the structural advantage spiral winding, and tube thickness [10]. Compared with the of the D-type specimen is evident. The displacement of the specimen in Ref [3], the specimens in our work have thicker D-type structure is increased as much as twice, butits strength tube walls. For the D-type specimen, the double-helical ele- is maintained at a level of 85% of the maximum compressive ment, the two inversely wound fiber layers restrain each other strength. In other words, at the expense of 15% strength loss, and thus reduce the possibility of buckling. In other words the plasticity of the double- helical structure is increased by the structural stability is increased. However. compared with 200% the plain A-type specimen, the double-helical structure The tensile property is always very important for any struc- improves the plasticity to some extent ture. To compare the tensile behavior of the spiral and non- What was analyzed above is for a single fiber cylinde spiral structures, three types of tensile specimens were made However, compared with the A-type structure, which can be and tested Since the tensile load is very high and the pressure thought of as a model of a bundle of fibers in laminates, the stress of the tabbed region is of considerable value, to prevent D-type structures have other advantages when they are used a collapse occurring in the end part under the pressure of jigs, in bundle form. The firm attachment of a fiber cylinder the tabbed region was filled inside with iron wire and was other adjacent ones can effectively prevent them from twist- einforced outside with glass fiber and epoxy resin. The test g. Hence, there exists a restraint against any shear strain ing speed for the tensile modulus is 2 mm min- and 5 mm which might otherwise result from the application of a normal min-I for the tensile strength. The results of the apparent stress along the fiber cylinder axis. More specifically, the tensile modulus and the tensile strength of the three types of restraint arises because, in the double cylinder wall of two specimen are listed in Table 4. For the tensile property, adjacent cylinders, the same helical sense of equivalent layers according to the classical theory of fibrous composite mate. in both cylinders will mean opposite signs of the helical angle rials, there is no difference between structures a and b in the two layers. The shear strains of the separate equivalent For the spirally wound tube under tension load, an inter layers would thus also be of opposite sign, but since the layers esting phenomenon of tension buckling was observed by Page are connected and two cylinder walls must deform as a unit, et al. when they studied wood tracheid in 1971[9]. Although the shear strain is effectively restrained not all the fibers in a given cross-section of wood actually On the basis of above experimental data and analysis,a buckle in this manner when wood fractures, a considerable useful conclusion can be drawn: a double- helical fiber struc
128 S.H. Li et al. /Materials Science and Engineering: C 3 (1995) 125-130 40 30 s ‘0 20 (P s 10 0 0 I 2 3 4 5 Dirplacement (mm) Dieplacement (mm) Fig. 3. Typical curve of the D-type specimen under compressive load. Fig. 4. Load-displacement curve of the type-C specimen under tension. mechanics of the materials, can give a rough comparison of the maximum normal stress. This can be called the ‘apparent flexural strength’, a parameter of the relative capacity to bear a bending load. From the calculated results listed in Table 4, it can be seen that the D-type specimens show no inferiority to the other types of structure in bearing the bending load. For the compressive test, the load-displacement curve of the D-type specimen is much different from those of the others. Its typical curve is shown in Fig. 3. If only from the viewpoint of compressive strength, the D-type structure is closer to the A type, but is better than the C-type structure. However, if the pseudo-plastic phenomenon which occurred in the D-type specimen is considered, the structural advantage of the D-type specimen is evident. The displacement of the D-type structure is increased as much as twice, but its strength is maintained at a level of 85% of the maximum compressive strength. In other words, at the expense of 15% strength loss, the plasticity of the double-helical structure is increased by 200%. The tensile property is always very important for any structure. To compare the tensile behavior of the spiral and nonspiral structures, three types of tensile specimens were made and tested. Since the tensile load is very high and the pressure stress of the tabbed region is of considerable value, to prevent a collapse occurring in the end part under the pressure of jigs, the tabbed region was filled inside with iron wire and was reinforced outside with glass fiber and epoxy resin. The testing speed for the tensile modulus is 2 mm min- ’ and 5 mm min-’ for the tensile strength. The results of the apparent tensile modulus and the tensile strength of the three types of specimen are listed in Table 4. For the tensile property, according to the classical theory of fibrous composite materials, there is no difference between structures A and B. For the spirally wound tube under tension load, an interesting phenomenon of tension buckling was observed by Page et al. when they studied wood tracheid in 197 1 [ 91. Although not all the fibers in a given cross-section of wood actually buckle in this manner when wood fractures, a considerable number of them, perhaps about lo%, do. This phenomenon was then applied in engineering composite materials and the work of fracture was increased successfully at the expense of a moderate loss of stiffness and axial strength [ 31. In our tension experiment, the so-called pseudo-plasticity existed only in the C-type specimen, as shown in Fig. 4, although not as obvious as reported in Ref. [ 31 for the long spirally wound tube. The fiber fully aligned A-type specimens fracture abruptly after the maximum load. This can be explained as follows. According to the buckling theory of composite materials, the critical buckling stress is a function of the principal elastic constants of the tube, the angle of the spiral winding, and tube thickness [ lo]. Compared with the specimen in Ref. [ 31, the specimens in our work have thicker tube walls. For the D-type specimen, the double-helical element, the two inversely wound fiber layers restrain each other and thus reduce the possibility of buckling. In other words, the structural stability is increased. However, compared with the plain A-type specimen, the double-helical structure improves the plasticity to some extent. What was analyzed above is for a single fiber cylinder. However, compared with the A-type structure, which can be thought of as a model of a bundle of fibers in laminates, the D-type structures have other advantages when they are used in bundle form. The firm attachment of a fiber cylinder to other adjacent ones can effectively prevent them from twisting. Hence, there exists a restraint against any shear strain which might otherwise result from the application of a normal stress along the fiber cylinder axis. More specifically, the restraint arises because, in the double cylinder wall of two adjacent cylinders, the same helical sense of equivalent layers in both cylinders will mean opposite signs of the helical angle in the two layers. The shear strains of the separate equivalent layers would thus also be of opposite sign, but since the layers are connected and two cylinder walls must deform as a unit, the shear strain is effectively restrained. On the basis of above experimental data and analysis, a useful conclusion can be drawn: a double-helical fiber struc-
S.H. Liet al. Materials Science and Engineering: C3(1995)125-130 ture has the optimum comprehensive performance compared with other structural forms. A single-helical fiber structural model is too simple to reproduce the superiority of a plant fiber which is essentially a multi-layered helical structure The double-helical structural element- one thick layer with Fig. 6. A simplified biomimetic model of the transition zone imitating bam- a small spiral microfibrillar angle and a thin layer with a boo tber greater angle--is probably the structural unit of bamboo bast layers and the spiral angle of the fiber in it can be designed 2 to meet different requirements for plasticity, strength and structural stability Fig. 4. Biomimicry of the transition zone in a bamboo fiber simplified plane model rather than a rcal spatial spiral was designed (as shown in Fig. 6) and was verified by engi We know that bamboo bast fib possesses a very neering composite materials cated structure, from the macro to micro scale. In particular Between two normal layers, a transition zone was formed bamboo bast fiber is, to some extent, similar to other kinds by inserting several additional sub-layers in order to avoid of plant cells or fibers, as we described earlier. However, the the abrupt change in the angle of the principal axis of the two ultrafine structure of bamboo bast fiber is somewhat different adjacent layers, The sub-layers are thinner than the normal from others, at least from the published literature. From the ones. The fiber angle of the sub-layer was designed in such a observations of Wai et al. [7], bamboo bast fiber has a way that the sub-layers will divide the fiber angle difference detailed ultrafine structure between broad and thin layers, as of the adjacent layer into equal parts. First, an engineering shown in Fig. 5(h composite material of glass fiber reinforced epoxy resin was alternating broad and thin layers. Let us pay special attention without a transition zone was also prepared(like FIg. o nen From Fig. 5 it can be seen that bamboo fiber contains employed, and for comparison another kind of specin to the interface between the thick and thin layers, namely the For many engineering applications, composite materials transition zone. Usually there are several sub-layers in the are used in laminated form and in such cases delamination is transition zone and the microfibrils there change their eleva- one of the main modes of damage and failure. The interlam tion angle gradually from one layer to the adjacent one. This inar shear modulus and ultimate stress are therefore both very phenomenon undoubtedly increases the complexity of the important parameters to be considered in the design of struc microstructure of a bamboo fiber. From the viewpoint of tures. Several methods have been suggested to measure the biological evolution they must have some function. What is interlaminar shear strength of fiber-reinforced composites the use of the ition zone? obviously the continuity of The most commonly used method is to subject a short thick the physical properties of the adjacent layers can be improved. beam to three-point loading until failure occurs by shear on Do they have any infuence on the mechanical behavior of the central plane. It has also been reported [11] that the short beam method cannot be recommended as an accurate way to It is natural for us to imagine that this transition zone acquire data for design purposes. Besides short beam,the bably has some effect on the inter-layer property. So, a double-side grooved specimen[ 12] becomes more common in the test of interlaminar shear properties Here, both short beam specimens and grooved specimens ere used to measure the interlaminar shear strength (ILSS) For the glass fiber/epoxy resin specimens, the interlaminar shear strength was measured by using a two-sided grooved specimen, as shown in Fig. 7. The experimental results are shown in Fig 8, where it can be seen that the transition zone slightly increased the interlaminar shear strength material was also used, i. e glass fiber reinforced polyester This time the ply mode was [+12/-12]4s and(+12)4/ +4/-4/(-12)4. The sub-layer with the angle of 4 is made from different glass strands and is thus thinner. This time the short beam specimen for three-point bending was exploited ig. 5. Schematic illustration of the secondary wall structure of a bamboo to test interlaminar shear strength. Eight specimens were fiber. (a) The structure of a fiber; (b)the detailed structure of (a)showi tested for each 8. The the transition zone. (After Wai et al. [7].) span is 19 mm and the diameter of the nose is 20 mm
S.H. Li et al. /Materials Science and Engineering: C 3 (1995) 125430 129 ture has the optimum comprehensive performance compared with other structural forms. A single-helical fiber structural model is too simple to reproduce the superiority of a plant fiber which is essentially a multi-layered helical structure. The double-helical structural element--one thick layer with a small spiral microfibrillar angle and a thin layer with a greater angle-is probably the structural unit of bamboo bast fiber. For its engineering application, the thickness of two layers and the spiral angle of the fiber in it can be designed to meet different requirements for plasticity, strength and structural stability. 4. Biomimicry of the transition zone in a bamboo fiber We know that bamboo bast fiber possesses a very complicated structure, from the macro to micro scale. In particular, bamboo bast fiber is, to some extent, similar to other kinds of plant cells or fibers, as we described earlier. However, the ultrafine structure of bamboo bast fiber is somewhat different from others, at least from the published literature. From the observations of Wai et al. [7], bamboo bast fiber has a detailed ultrafine structure between broad and thin layers, as shown in Fig. 5 (b) . From Fig. 5 it can be .seen that bamboo fiber contains alternating broad and thin layers. Let us pay special attention to the interface between the thick and thin layers, namely the transition zone. Usually there are several sub-layers in the transition zone and the microfibrils there change their elevation angle gradually from one layer to the adjacent one. This phenomenon undoubtedly increases the complexity of the microstructure of a bamboo fiber. From the viewpoint of biological evolution they must have some function. What is the use of the transition zone? Obviously the continuity of the physical properties of the adjacent layers can be improved. Do they have any influence on the mechanical behavior of bamboo fiber? It is natural for us to i-magine that this transition zone probably has some effect on the inter-layer property. So, a L4 N3 L3 - N2 - LI L3 N2 (a) (b) Fig. 5. Schematic illustration of the secondary wall stracture of a bamboo fiber. (a) The struch~re of a fiber; (b) the detailed structure of (a) showing the transition zone. (After Wai et al. [ 71.) Fig. 6. A simplified biomimetic model of the transition zone imitating bamboo fiber. simplified plane model rather than a real spatial spiral one was designed (as shown in Fig. 6) and was verified by engineering composite materials. Between two normal layers, a transition zone was formed by inserting several additional sub-layers in order to avoid the abrupt change in the angle of the principal axis of the two adjacent layers. The sub-layers are thinner than the normal ones. The fiber angle of the sub-layer was designed in such a way that the sub-layers will divide the fiber angle difference of the adjacent layer into equal parts. First, an engineering composite material of glass fiber reinforced epoxy resin was employed, and for comparison another kind of specimen without a transition zone was also prepared (like Fig. 6). For many engineering applications, composite materials are used in laminated form and in such cases delamination is one of the main modes of damage and failure. The interlaminar shear modulus and ultimate stress are therefore both very important parameters to be considered in the design of structures. Several methods have been suggested to measure the interlaminar shear strength of fiber-reinforced composites. The most commonly used method is to subject a short thick beam to three-point loading until failure occurs by shear on the central plane. It has also been reported [ 111 that the short beam method cannot be recommended as an accurate way to acquire data for design purposes. Besides short beam, the double-side grooved specimen [ 121 becomes more common in the test of interlaminar shear properties. Here, both short beam specimens and grooved specimens were used to measure the interlaminar shear strength (ILSS) . For the glass fiber/epoxy resin specimens, the interlaminar shear strength was measured by using a two-sided grooved specimen, as shown in Fig. 7. The experimental results are shown in Fig. 8, where it can be seen that the transition zone slightly increased the interlaminar shear strength. To verify this conclusion, another engineering composite material was also used, i.e. glass fiber reinforced polyester. This time the ply mode was [ + 12/- 12],, and ( + 12),/ +4/ - 4/ ( - 12),. The sub-layer with the angle of 4” is made from different glass strands and is thus thinner. This time the short beam specimen for three-point bending was exploited to test interlaminar shear strength. Eight specimens were tested for each group and the results are shown in Fig. 8. The span is 19 mm and the diameter of the nose is 20 mm
S H Li et al. Materials Science and Engineering: C3(1995)125-130 2A without E3 improve the plasticity, some amount of single-helical rein- transtion z°ne transit。nz°n forcements could be combined with double-helical ones, so that under certain tensile stress, some reinforcement will buc. kle and elongate. It was reported that in wood only a small amount of the fibers(10%)will buckle when wood fractures For the biomimetic transition zone model, it can easily be applied in laminates to improve the interlaminar shear prop- erties 30 6. Conclusions 10 (1)The double-helical structural unit possesses the opti num comprehensive mechanical properties. The single-hel- GF/Ep。xy GF/Polyester ical structure is too simple to reproduce the superiority of plant fibers which are essentially multi-layered helical struc- Fig8. Verification of the biomimetic model of the transition zone with glass tures (2) The transition zone in bamboo bast fiber can improve From Fig 8, the ILSS of the specimens with a transition the inter-layer property. The verification tests show that the zone are about 15.8% and 13. 3% higher than those without interlaminar shear strength of glass fiber/epoxy resin and for glass fiber/epoxy and glass fiber/polyester, respectively. glass fiber/polyester are increased by about 15%after the On the basis of the above experimental results, we can draw introduction of such a transition zone the following conclusion: the sub-layer in the transition zone of bamboo will increase the inter-layer shear property and improve the geometrical and physical continuities of the adja Acknowledgment e ausPices The biomimicry experiments above have a two-fold mean- This work was perform ing: on the one hand, they give solid proof that the transition Tational Nature Science Foundation of China zones in bamboo fiber have a significant effect on the inter layer property. On the other hand, the concept stored in nat References ural biomaterials can be applied in engineering composite materials, especially where the interlaminar property is of [1]A V Srinivasan, G.K. Haritos and F L. Hedberg, Appl. Mech. Rev., 44 particular importance. It can easily be inferred that the tran (1991)463 silion zone will also increase the interlaminar shear modulus I(1992) within the area between the two principal axes of the adjacent [313E. Gordon and g Jeronimidis, Phil. Trans. R. Soc. Lon, A 294 la [4]R C. Chaplin, J.E. Gordon and G Jeronimidis, U.S. Patent no 4, 409 (1983)274 L5]SHLl, Q.Y. Zeng, S.Y. Fu and B L. Zhou, Biomimetics, 2(1993) 5. Some discussion about the application of these biomimetic models in engineering composite materials [6] D. Fengel and X Shao, Wood Sci. Technol., 18(1984)103. [7] N.N. Wai, H Nanko and K Murakami, Wood Sci. TechnoL., 19(1985) The double-helical reinforcing element model can be [8]SH. Li, Q.Y. Zeng, x. Chen and B L. Zhou, J. Mater. Sci. Technol. applied to engineering composite materials for better com 0(1994)34 prehensive mechanical behavior. To meet fferentreq [9]D H Page, F. El Hossseiny and K, winkler, Nature, 229(1971)252. rements, the thickness ratio of the broad and thin layers, the [10] N.J. Pagano, J C Halpin and J M. Whitney, J Comp. Mater, 2(1968) elevation angle of the fiber in each layer, and the number of [11]J B Sturgeon, RAE Technical Report 71026(1971). reinforcements with pseudo-plasticity can all be designed To [12]MF. Markhan and D. Dawson, Composites, 6(1975)173
130 S.H. Li et al. /Materials Science and Engineering: C 3 (1995) 125-130 m Without B with a tranrition zone tranrltion zone 2 6o 3 2 F 50 . s 40 - (10 $ 30. f 20 - a .E ii 10 . i: 0 OE GF/Epoxy QF/Polyerter Fig. 8. Verification of the biomimetic model of the transition zone with glass fiber/epoxy resin and glass fiber/polyester. From Fig. 8, the ILSS of the specimens with a transition zone are about 15.8% and 13.3% higher than those without for glass fiber/epoxy and glass fiber/polyester, respectively. On the basis of the above experimental results, we can draw the following conclusion: the sub-layer in the transition zone of bamboo will increase the inter-layer shear property and improve the geometrical and physical continuities of the adjacent layers. The biomimicry experiments above have a two-fold meaning: on the one hand, they give solid proof that the transition zones in bamboo fiber have a significant effect on the interlayer property. On the other hand, the concept stored in natural biomaterials can be applied in engineering composite materials, especially where the interlaminar property is of particular importance. It can easily be inferred that the transition zone will also increase the interlaminar shear modulus within the area between the two principal axes of the adjacent layers. 5. Some discussion about the application of these biomimetic models in engineering composite materials The double-helical reinforcing element model can be applied to engineering composite materials for better comprehensive mechanical behavior. To meet the different requirements, the thickness ratio of the broad and thin layers, the elevation angle of the fiber in each layer, and the number of reinforcements with pseudo-plasticity can all be designed. To improve the plasticity, some amount of single-helical reinforcements could be combined with double-helical ones, so that under certain tensile stress, some reinforcement will buckle and elongate. It was reported that in wood only a small amount of the fibers ( 10%) will buckle when wood fractures. For the biomimetic transition zone model, it can easily be applied in laminates to improve the interlaminar shear properties. 6. Conclusions ( 1) The double-helical structural unit possesses the optimum comprehensive mechanical properties, The single-helical structure is too simple to reproduce the superiority of plant fibers which are essentially multi-layered helical structures. (2) The transition zone in bamboo bast fiber can improve the inter-layer property. The verification tests show that the interlaminar shear strength of glass fiber/epoxy resin and glass fiber/polyester are increased by about 15% after the introduction of such a transition zone. Acknowledgment This work was performed under the auspices of the National Nature Science Foundation of China. References [ 1] A.V. Srinivasan, G.K. Haritos and F.L. Hedberg, Appl. Mech. Rev., 44 (1991) 463. [2] J.F.V. Vincent and A.V. Srinivasan, Biomimetics, I (1992) 1. [3] J.E. Gordon and G. Jeronimidis, Phil. Tram. R. Sot. Lon., A 294 (1980) 545. [4] R.C. Chaplin, J.E. Gordon and G. Jeronimidis, U.S. Patent no.4, 409 (1983) 274. [5] S.H. Li, Q.Y. Zeng, S.Y. Fu and B.L. Zhou, &mime&, 2 (1993) 15. [6] D. Fengel and X. Shao, Wood&i. Technol., 18 (1984) 103. [7] N.N. Wai. H. Nanko and K. Murakami, Wood.%‘. Technof., 19 ( 1985) 211. [8] S.H. Li, Q.Y. Zeng, X. Chen and B.L. Zhou, J. Mater. Sci. Technol., 10 (1994) 34. [9] D.H. Page, F.El-Hossseiny and K. Winkler, Nature, 229 (1971) 252. [ 101 N.J. Pagano, J.C. Halpinand J.M. Whitney,.I. Camp. Mater., 2 (1968) 154. [ 111 J.B. Sturgeon, RAE Technical Reporr 71026 (1971). [ 121 M.F. Markhan and D.Dawson, Composires, 6 (1975) 173