点击切换搜索课件文库搜索结果(990)
文档格式:PDF 文档大小:586.39KB 文档页数:24
1.历史、发展和当前状况 2.坐标系统与时间系统 3.卫星轨道运动及GPS卫星的坐标计算 4.GPS卫星信号与传播 5.GPS观测量、观测方程及误差分析 6.绝对(单点)定位原理
文档格式:PPT 文档大小:240KB 文档页数:42
公路工程一般由路线、桥涵、隧道及各种附属 设施等构成。兴建公路之前,为了选择一条既 经济又合理的路线,必须对沿线进行勘测。 一般地讲,路线以平、直最为理想。但实际上, 由于受到地物、地貌、水文、地质及其它等因 素的限制,路线的平面线型必然有转折,即路 线前进的方向发生改变。为保证行车舒适、安 全,并使路线具有合理的线型,在直线转向处 必须用曲线连接起来,这种曲线称为平曲线。 平曲线包括圆曲线和缓和曲线两种
文档格式:PDF 文档大小:1.03MB 文档页数:7
1. Basic Knowledge of GPS In 1973, DOd organized a Joint P Office (JPO) located at the U.S. Air Force Systems Command's Space The s Second Lecture Division, Los Angeles Air Force Base(AFB)to what?
文档格式:PDF 文档大小:190.94KB 文档页数:6
1.1 Terminology Definitions 3. Point Positioning ys. Relative positioning The coordinates of a single point are determined when 1. Code Range vs, Carrier Phase Code measurements(meter level) Carrier phase measurements(millimeter range). Single point positioning
文档格式:PDF 文档大小:741.62KB 文档页数:4
This is a Geodetic Control Test Field located at L Radial Surveying( Cartwheel): Madison County, Central Ohio. lial Surveys: one receiver at a fixed 2 Madison County High Altitude Test Range site, and measuring lines from this fixed
文档格式:PDF 文档大小:599.28KB 文档页数:6
1.1 Physical Fundamentals This attenuation is usually expressed in decibels (dB). By definition, an attenuation of n dB means signal propagation from the that the original field strength is decreased by ite to the user by means of factor of 10-0In electromagnetic waves. Such waves Physical quantities
文档格式:PDF 文档大小:587.76KB 文档页数:9
Perigee and Apogee: The point of closest approach of the satellite with respect to the earth's center of mass is called perigee and the most distant position is the apogee. Nodes: The intersection between the equatorial and the nit sphere is termed the nodes, where the ascending node defines the northward
文档格式:PDF 文档大小:721.27KB 文档页数:15
Outline Review u Examined basics of GPS signal structure and how gnal is tracked a Looked at methods used to acquire satellites and start g Today we look at
文档格式:PPT 文档大小:160KB 文档页数:26
1、量距的工具钢尺、标杆、测钎、垂球 2、钢尺量距的方法钢尺量距的基本步骤是:直线定线、量距和数据整理两点间的距离大于尺长时,需分段丈量。将各分段点置于一条直线上的工作叫直线定线。直线定线方法有目测法和仪器法两种
文档格式:PDF 文档大小:17.81MB 文档页数:499
第一章半导体材料导电型号、电阻率、少数载流子寿命的测量 第二章化学腐蚀一光学方法检测晶体缺陷和晶向 第三章霍尔系数、迁移率和杂质补偿度的测量 第四章外延片的物理测试 第五章红外吸收光谱在半导体测试技术中的应用 第六章扫描电子显微镜及其在半导体测试技术中的应用 第七章透射电子显微镜晶体缺陷分析 第八章Ⅹ射线在半导体测试技术中的应用 第九章结电容和CV测试技术 第十章半导体中痕量杂质分析
首页上页7172737475767778下页末页
热门关键字
搜索一下,找到相关课件或文库资源 990 个  
©2008-现在 cucdc.com 高等教育资讯网 版权所有