Part I Wastewater Engineering 1 Wastewater Engineering: An Overview Every community produces both liquid and solid wastes and air emissions. The liquid waste-wastewater is essentially the water supply of the community after it has been used in a variety of applications. From arried wastes removed from residences. institutions. and commercial and industrial establishmer ogether with such groundwater surface water and stormwater as may be present. When wastewater accumulates and is allowed to go septic, the decomposition of the organic matter it contains will lead to nuisance conditions including the production of malodorous gases. In addition, untreated wastewater contains numerous pathogenic microorganisms that dwell in the human intestina tract. Wastewater also contains nutrients, which can stimulate the growth of aquatic plants, and may contain toxic compounds or compounds that potentially may be mutagenic or carcinogenic. For these reasons, the immediate and nuisance-free removal of wastewater from its sources of generation, followed by treatment, reuse, or dispersal into the environment is necessary to protect public health and the environment Wastewater engineering is that branch of environmental engineering in which basic principles of science nd engineering are applied to solving the issues associated with the treatment and reuse of wastewater. goal of wastewater engineering is the protection of public health in a manner commensurate with environmental, economic, social and political concerns. To protect public health and the environment. it is necessary to have knowledge of (D) environment,(3)the transformation and wastewater. and (5) methods for Combined sewer beneficial use or disposal of solids To provide an initial perspective on the field of wastewater engineering, common terminology is defined and introduced first Fig. 1-1 Schematic diagram of management infrastructure 1-1 Terminology In the literature, and in governmental regulations, a variety of terms have been used for individual constituents of concern in wastewater. The terminology used commonly for key concepts and terms in the field of wastewater management is summarized in Table 1-1 In some cases, confusion and undue negative perceptions arise with the use of the terms contaminants, impurities, and pollutants, which are often used interchangeably. To avoid confusion, the term constituent is used in this text in place of an individual compound or element, such as ammonia nitrogen. The term 1-1
1-1 Part I Wastewater Engineering 1 Wastewater Engineering:An Overview Every community produces both liquid and solid wastes and air emissions. The liquid waste-wastewater, is essentially the water supply of the community after it has been used in a variety of applications. From the standpoint of sources of generation, wastewater may be defined as a combination of the liquid or water-carried wastes removed from residences, institutions, and commercial and industrial establishments, together with such groundwater, surface water, and stormwater as may be present. When wastewater accumulates and is allowed to go septic, the decomposition of the organic matter it contains will lead to nuisance conditions including the production of malodorous gases. In addition, untreated wastewater contains numerous pathogenic microorganisms that dwell in the human intestinal tract. Wastewater also contains nutrients, which can stimulate the growth of aquatic plants, and may contain toxic compounds or compounds that potentially may be mutagenic or carcinogenic. For these reasons, the immediate and nuisance-free removal of wastewater from its sources of generation, followed by treatment, reuse, or dispersal into the environment is necessary to protect public health and the environment. Wastewater engineering is that branch of environmental engineering in which basic principles of science and engineering are applied to solving the issues associated with the treatment and reuse of wastewater. The ultimate goal of wastewater engineering is the protection of public health in a manner commensurate with environmental, economic, social, and political concerns. To protect public health and the environment, it is necessary to have knowledge of (1) constituents of concern in wastewater, (2) impacts these constituents when wastewater is dispersed into the environment, (3) the transformation and long-term fate of these constituents in treamtent processes, (4) treatment methods that can be used to remove or modify the constituents found in wastewater, and (5) methods for beneficial use or disposal of solids generated by the treatment systems. To provide an initial perspective on the field of wastewater engineering, common terminology is defined and introduced first. Fig. 1-1 Schematic diagram of a wastewater management infrastructure 1-1 Terminology In the literature, and in governmental regulations, a variety of terms have been used for individual constituents of concern in wastewater. The terminology used commonly for key concepts and terms in the field of wastewater management is summarized in Table 1-1. In some cases, confusion and undue negative perceptions arise with the use of the terms contaminants, impurities, and pollutants, which are often used interchangeably. To avoid confusion, the term constituent is used in this text in place of an individual compound or element, such as ammonia nitrogen. The term
characteristic is used to refer to a group of constituents, such as physical or biological characteristics The term "sludge"has been used for many years to signify the residuals produced from wastewater treatment, in 1994, the Water Environment Federation adopted a policy defining"biosolids as a primarily organic, solid wastewater treatment product that can be recycled beneficially. In this policy, " solids"are defined as the residuals that are derived from the treatment of wastewater solids that have been treated to the point at which they are suitable for beneficial use are termed"biosolids. In this text. the terms of solids and biosolids are used extensively, but"" continues to be used. especially in cases where 1-2 Impact of Regulations on Wastewater Engineering From about 1900 to the early 1970s, treatment obiectives were concerned primarily with(1) the removal of colloidal, suspended, and floatable material. (2)the treatment of biodegradable organics, and(3) the on of pathogenic organisms. Implementation in the United States of the Federal Water Pollution Control Act Amendments of 1972(Public Law 92-500). also known as the Clean Water Act(CWA stimulated substantial changes in wastewater treatment to achieve the obiectives of "fishable and swimmable"waters. Unfortunately, these objectives were not uniformly met From the early 1970s to about 1980, wastewater treatment objectives were based primarily on aesthetic and environmental concerns. The earlier objectives involving the reduction of biological oxygen demand ( BOD), total suspended solids(TSs), and pathogenic organisms continued but at higher levels. Removal of nutrients, such as nitrogen and phosphorus, also began to be addressed, particularly in some of the inland streams and lakes, and estuaries and bays. Major programs were undertaken by both state and federal agencies to achieve more effective and widespread treatment of wastewater to improve the quality of the surface waters. These programs were based on(D) an increased understanding of the environmental effects caused by wastewater discharges:(2)a greater appreciation of the adverse long-term effects caused by the discharge of some of the specific constituents found in wastewater: and (3 )the development of national concern for the protection of the environment. As a result of these programs, significant improvements have been made the quality of the surface waters Table I-I Terminology ly used in the field of wastewater engineerin Biosolids Primarily an organic, semisolid wastewater product that remains after solids are stabilized biologically or chemically and are suitable far beneficial use Class a biosolids Biosolids in which the pathogens are reduced below current detectable Class a biosolids Biosolids in which the pathogens are reduced to levels that are unlikely to pose a threat to the public health and the environment under specific use conditions. Class b biosolids cannot be sold or given away in bags or other containers or applied on lawns or home gardens Characteristics General classes of wastewater constituents such as physical, chemical (wastew biological and biochemical Composition The makeup of wastewater, including the physical, chemical, and biological constituents Constituents Individual components, elements, or biological entities such as Contaminants Disinfection Reduction of disease-causing microorganisms by physical or chemical Effluent The liquid discharged from a processing step Constituents added to the water supply through use Non-point sources Sources of pollution that originate from multiple sources over a relatively large area Nutrient An element that is essential for the growth of plants and animals Nutrients in wastewater, usually nitrogen and phosphorus, may cause unwanted algal and plant growths in lakes and streams Point sources Pollutional loads discharged at a specific location from pipes, outfall 1-2
1-2 characteristic is used to refer to a group of constituents, such as physical or biological characteristics. The term “sludge” has been used for many years to signify the residuals produced from wastewater treatment, in 1994, the Water Environment Federation adopted a policy defining "biosolids' as a primarily organic, solid wastewater treatment product that can be recycled beneficially. In this policy, “solids” are defined as the residuals that are derived from the treatment of wastewater. Solids that have been treated to the point at which they are suitable for beneficial use are termed “biosolids.” In this text, the terms of solids and biosolids are used extensively, but “sludge” continues to be used, especially in cases where untreated solid material and chemical residuals are referenced. 1-2 Impact of Regulations on Wastewater Engineering From about 1900 to the early 1970s, treatment objectives were concerned primarily with (1) the removal of colloidal, suspended, and floatable material, (2) the treatment of biodegradable organics, and (3) the elimination of pathogenic organisms. Implementation in the United States of the Federal Water Pollution Control Act Amendments of 1972 (Public Law 92-500), also known as the Clean Water Act (CWA), stimulated substantial changes in wastewater treatment to achieve the objectives of “fishable and swimmable”waters. Unfortunately, these objectives were not uniformly met. From the early 1970s to about 1980, wastewater treatment objectives were based primarily on aesthetic and environmental concerns. The earlier objectives involving the reduction of biological oxygen demand (BOD), total suspended solids (TSS), and pathogenic organisms continued but at higher levels. Removal of nutrients, such as nitrogen and phosphorus, also began to be addressed, particularly in some of the inland streams and lakes, and estuaries and bays. Major programs were undertaken by both state and federal agencies to achieve more effective and widespread treatment of wastewater to improve the quality of the surface waters. These programs were based, in part, on (1) an increased understanding of the environmental effects caused by wastewater discharges; (2) a greater appreciation of the adverse long-term effects caused by the discharge of some of the specific constituents found in wastewater; and (3)the development of national concern for the protection of the environment. As a result of these programs, significant improvements have been made in the quality of the surface waters. Table 1-1 Terminology commonly used in the field of wastewater engineering Term Definition Biosolids Primarily an organic, semisolid wastewater product that remains after solids are stabilized biologically or chemically and are suitable far beneficial use Class A biosolids Biosolids in which the pathogens are reduced below current detectable levels Class A biosolids Biosolids in which the pathogens are reduced to levels that are unlikely to pose a threat to the public health and the environment under specific use conditions. Class B biosolids cannot be sold or given away in bags or other containers or applied on lawns or home gardens Characteristics (wastewater) General classes of wastewater constituents such as physical, chemical, biological, and biochemical Composition The makeup of wastewater, including the physical, chemical, and biological constituents Constituents Individual components, elements, or biological entities such as suspended solids or ammonia nitrogen Contaminants Constituents added to the water supply through use Disinfection Reduction of disease-causing microorganisms by physical or chemical means Effluent The liquid discharged from a processing step Impurities Constituents added to the water supply through use Non-point sources Sources of pollution that originate from multiple sources over a relatively large area Nutrient An element that is essential for the growth of plants and animals. Nutrients in wastewater, usually nitrogen and phosphorus, may cause unwanted algal and plant growths in lakes and streams Parameter A measurable factor such as temperature Point Sources Pollutional loads discharged at a specific location from pipes, outfalls
and conveyance methods from either municipal wastewater treatment lants or industrial waste treatment facilities Pollutants water Reclamation Treatment of wastewater fur subsequent reuse application or the act of using treated wastewater The reuse of treated wastewater and biosolids for beneficial purposes R euse Beneficial use of reclaimed or repurified wastewater or stabilized Sludge and solids Solids removed from wastewater during treatment. Solids that are treated further am termed Since 1980, the water quality improvement objectives of the 1970s have continued, but shifted to the definition and removal of constituents that may cause long-term health effects and environmental impacts. Consequently while the early treatment obiectives remain valid today. the required degree of treatment has increased significantlv and additional treatment obiectives and goals have been added. Therefore, treatment obiectives must go hand in hand with the water quality obiectives Recent regulations that ies design inc beneficial use of biosolids. In the biosolids regulation promulgated in 1993. national standards were set for pathogen and heavy metal content and for the safe handling and use of biosolids. The standards are designed to protect human health and the environment where biosolids are applied beneficially to land The rule also promotes the development of a"clean sludge(U.s. EPA, 1999 The total maximum daily load (TMDL) program was promulgated in 2000 but is not scheduled to be in effect until 2002. The Tmdl rule is designed to protect ambient water quality. A TMDL represents the maximum amount of a pollutant that a water body can receive and still meet water quality standards. A TMDL is the sum of (1)the individual waste-load allocations for point sources,(2) load allocations fo nonpoint sources, (3)natural background levels, and(4)a margin of safety (U.S. EPA, 2000). To implement the rule a comprehensive watershed-based water quality management program must be undertaken to find and control nonpoint sources in addition to conventional point source discharges. With implementation of the TMDL rule. the focus on water quality shifts from technology-based controls to preservation of ambient water quality. The end result is an integrated planning approach that transcends jurisdictional boundaries and forces different sectors. such as agriculture, water and wastewater utilities and urban runoff managers, to cooperate. Implementation of the TMDL rule will vary depending on the specific water quality objectives established for each watershed and, in some cases, will require the installation of advanced levels of treatment 1-3 Health and Environmental Concerns in Wastewater Management As research into the characteristics of wastewater has become more extensive, and as the techniques for analyzing specific constituents and their potential health and environmental effects have become more comprehensive, the body of scientific knowledge has expanded significantly. Many of the new treatment methods being developed are designed to deal with health and enviro indings of recent research. However the advancement in treatment technology effectiveness has not kept ace with the enhanced constituent detection capability. Pollutants can be detected at lower concentrations than can be attained by available treatment technology Therefore, careful assessment of health and environment effects and community concerns about these effects becomes increasingly important in wastewater management The need to establish a dialogue with the community is important to assure that health and environmental issues are being addressed. Water quality issues arise when increasing amounts of treated wastewater are discharged to water bodies that are eventually used as water supplies. The waters of the Mississippi river and many rivers in the eastern United States are used for municipal and industrial water supplies and as repositories for the esulting treated wastewater. In southern California. a semiarid region. increasing amounts of reclaimed wastewater are being used or are planned to be used for groundwater recharge to augment existing potable water supplies. Significant questions remain about the testing and levels of treatment necessary to protect human health where the commingling of highly treated wastewater with drinking water sources results in indirect potable reuse. Some professionals obiect in principle to the indirect reuse of treated wastewater for potable purposes: others express concern that current techniques are inadequate for detecting all microbial and chemical contaminants of health significance. Among the latter concerns are(1)the lack of 1-3
1-3 and conveyance methods from either municipal wastewater treatment plants or industrial waste treatment facilities Pollutants Constituents added to the water supply through use Reclamation Treatment of wastewater fur subsequent reuse application or the act of reusing treated wastewater Recycling The reuse of treated wastewater and biosolids for beneficial purposes Reuse Beneficial use of reclaimed or repurified wastewater or stabilized biosolids Sludge and solids Solids removed from wastewater during treatment. Solids that are treated further am termed Since 1980, the water quality improvement objectives of the 1970s have continued, but the emphasis has shifted to the definition and removal of constituents that may cause long-term health effects and environmental impacts. Consequently, while the early treatment objectives remain valid today, the required degree of treatment has increased significantly, and additional treatment objectives and goals have been added. Therefore, treatment objectives must go hand in hand with the water quality objectives or standards established by the federal, state, and regional regulatory authorities. Recent regulations that affect wastewater facilities design include those for the treatment, disposal, and beneficial use of biosolids. In the biosolids regulation promulgated in 1993, national standards were set for pathogen and heavy metal content and for the safe handling and use of biosolids. The standards are designed to protect human health and the environment where biosolids are applied beneficially to land. The rule also promotes the development of a “clean sludge” (U.S. EPA, 1999). The total maximum daily load (TMDL) program was promulgated in 2000 but is not scheduled to be in effect until 2002. The TMDL rule is designed to protect ambient water quality. A TMDL represents the maximum amount of a pollutant that a water body can receive and still meet water quality standards. A TMDL is the sum of (1) the individual waste-load allocations for point sources, (2) load allocations for nonpoint sources, (3) natural background levels, and (4) a margin of safety (U.S. EPA, 2000). To implement the rule, a comprehensive watershed-based water quality management program must be undertaken to find and control nonpoint sources in addition to conventional point source discharges. With implementation of the TMDL rule, the focus on water quality shifts from technology-based controls to preservation of ambient water quality. The end result is an integrated planning approach that transcends jurisdictional boundaries and forces different sectors, such as agriculture, water and wastewater utilities, and urban runoff managers, to cooperate. Implementation of the TMDL rule will vary depending on the specific water quality objectives established for each watershed and, in some cases, will require the installation of advanced levels of treatment. 1-3 Health and Environmental Concerns in Wastewater Management As research into the characteristics of wastewater has become more extensive, and as the techniques for analyzing specific constituents and their potential health and environmental effects have become more comprehensive, the body of scientific knowledge has expanded significantly. Many of the new treatment methods being developed are designed to deal with health and environmental concerns associated with findings of recent research. However, the advancement in treatment technology effectiveness has not kept pace with the enhanced constituent detection capability. Pollutants can be detected at lower concentrations than can be attained by available treatment technology. Therefore, careful assessment of health and environment effects and community concerns about these effects becomes increasingly important in wastewater management. The need to establish a dialogue with the community is important to assure that health and environmental issues are being addressed. Water quality issues arise when increasing amounts of treated wastewater are discharged to water bodies that are eventually used as water supplies. The waters of the Mississippi River and many rivers in the eastern United States are used for municipal and industrial water supplies and as repositories for the resulting treated wastewater. In southern California, a semiarid region, increasing amounts of reclaimed wastewater are being used or are planned to be used for groundwater recharge to augment existing potable water supplies. Significant questions remain about the testing and levels of treatment necessary to protect human health where the commingling of highly treated wastewater with drinking water sources results in indirect potable reuse. Some professionals object in principle to the indirect reuse of treated wastewater for potable purposes; others express concern that current techniques are inadequate for detecting all microbial and chemical contaminants of health significance. Among the latter concerns are (1) the lack of
sufficient information regarding the health risks posed by some microbial pathogens and chemical constituents in wastewater, (2 )the nature of unknown or unidentified chemical constituents and potential pathogens, and (3)the effectiveness of treatment processes for their removal Other health concerns relate to:(I)the release of volatile organic compounds( vOCs) and toxic air contaminants(TACs) from collection and treatment facilities.(2)chlorine disinfection, and(3)disinfection byproducts( DBPs). Odors are one of the most serious environmental concerns to the public. Many industrial wastes contain vocs that may be flammable toxic and odorous and may be contributors Effluents containing chlorine residuals are toxic to aquatic life, and, increasingly, provisions to eliminate chlorine residuals are being instituted. Other important health issues relate to the reduction of disinfection byproducts(DBPs) that are potential atters. To achieve higher and ore consistent microbes inactivation levels improved performance of disinfection systems must be addressed. In many communities, the issues of safety in the transporting storing, handling of chlorine are also being examined Fig. 1-2 Covered treatment plant facilities for the control of odor emissions 1-4 Wastewater Characteristics Prior to about 1940. most municipal wastewater was generated from domestic sources. After 1940. as industrial development in the U.S. grew significantlv. increasing amounts of industrial wastewater have been and continue to be discharged to municipal collection systems. The amounts of heavy metals and synthesized organic compounds generated by industrial activities have increased, and some 10.000 new As technological changes take place in manufacturing changes also occur in the compounds discharge and the resulting wastewater characteristics. Numerous compounds generated from industrial processes re difficult and costly to treat by conventional wastewater treatment processes. Therefore, effective Enforcement of an industrial pretreatment, program is a daunting task and soz a ome of the regulated pollutants still escape to the municipal wastewater collection system and must be treated. In the future with the objective of pollution prevention, every effort should be made by industrial dischargers to assess the environmental impacts of any new compounds that may enter the wastewater stream before being pproved for use 1-5 Wastewater Treatment Wastewater collected from municipalities and communities must ultimately be returned to receiving waters or to the land or reused. The complex question facing the design engineer and public health officials is: what levels of treatment must be achieved in a given application-bevond those prescribed by discharge permits-to ensure protection of public health and the environment? The answer to this question quires detailed analyses of local conditions and needs, application of scientific knowledge and engineering judgement based on past experience, and considerations of federal, state, and local regulations Methods of treatment in which the application of physical forces predominate are known as unit operations. Methods of treatment in which the removal of contaminants is brought about by chemical or biological reactions are known as unit processes. At present time, unit operations and processes are grouped together to provide various levels of treatment known as preliminary primary, advanced primary ndary and tertiary treatment. See Tab 1-2. Tab 1-2 Levels of wastewater treatment Treatment level Description Preliminary Removal of wastewater constituents, such as rags, sticks, floatables, grit, and grease that may cause maintenance or operational problems with the treatment operations, processes, and ancillary systems
1-4 sufficient information regarding the health risks posed by some microbial pathogens and chemical constituents in wastewater,(2)the nature of unknown or unidentified chemical constituents and potential pathogens, and (3)the effectiveness of treatment processes for their removal. Other health concerns relate to: (1)the release of volatile organic compounds(VOCs) and toxic air contaminants(TACs) from collection and treatment facilities, (2)chlorine disinfection, and (3)disinfection byproducts(DBPs).Odors are one of the most serious environmental concerns to the public. Many industrial wastes contain VOCs that may be flammable,toxic, and odorous,and may be contributors to photochemical smog and tropospheric ozone. Effluents containing chlorine residuals are toxic to aquatic life, and, increasingly, provisions to eliminate chlorine residuals are being instituted. Other important health issues relate to the reduction of disinfection byproducts (DBPs) that are potential carcinogens and are formed when chlorine reacts with organic matters. To achieve higher and more consistent microbes inactivation levels, improved performance of disinfection systems must be addressed. In many communities, the issues of safety in the transporting, storing, and handling of chlorine are also being examined. Fig. 1-2 Covered treatment plant facilities for the control of odor emissions 1-4 Wastewater Characteristics Prior to about 1940, most municipal wastewater was generated from domestic sources. After 1940, as industrial development in the U.S. grew significantly, increasing amounts of industrial wastewater have been and continue to be discharged to municipal collection systems.The amounts of heavy metals and synthesized organic compounds generated by industrial activities have increased, and some 10,000 new organic compounds are added each year. As technological changes take place in manufacturing, changes also occur in the compounds discharged and the resulting wastewater characteristics. Numerous compounds generated from industrial processes are difficult and costly to treat by conventional wastewater treatment processes. Therefore, effective industrial pretreatment becomes an essential part of an overall water quality management program. Enforcement of an industrial pretreatment, program is a daunting task and some of the regulated pollutants still escape to the municipal wastewater collection system and must be treated. In the future with the objective of pollution prevention, every effort should be made by industrial dischargers to assess the environmental impacts of any new compounds that may enter the wastewater stream before being approved for use. 1-5 Wastewater Treatment Wastewater collected from municipalities and communities must ultimately be returned to receiving waters or to the land or reused. The complex question facing the design engineer and public health officials is: what levels of treatment must be achieved in a given application-beyond those prescribed by discharge permits-to ensure protection of public health and the environment? The answer to this question requires detailed analyses of local conditions and needs, application of scientific knowledge and engineering judgement based on past experience, and considerations of federal, state, and local regulations. In some cases, a detailed risk assessment may be required. Methods of treatment in which the application of physical forces predominate are known as unit operations. Methods of treatment in which the removal of contaminants is brought about by chemical or biological reactions are known as unit processes. At present time, unit operations and processes are grouped together to provide various levels of treatment known as preliminary, primary, advanced primary, secondary,and tertiary treatment. See Tab 1-2. Tab 1-2 Levels of wastewater treatment Treatment level Description Preliminary Removal of wastewater constituents, such as rags, sticks, floatables, grit, and grease that may cause maintenance or operational problems with the treatment operations, processes, and ancillary systems
Primary Removal of a portion of the suspended solids and organic matter from the Advanced Primary anced removal of suspended solids and organic matter from the wastewater Typically accomplished by chemical addition or filtration Secondar Removal of biodegradable organics, suspended solids. Disinfection is also ally included in the definition of conventional secondary treatment Tertian Removal of residual suspended solids, usually by granular medium filtration or microscreen. Disinfection is also typically a part of tertiary treatment. Nutrient In this Advanced Removal of dissolved and suspended materials remaining after normal biological treatment when required for various water reuse applications A listing of unit operations and processes used for the removal of major constituents found in wastewater is presented in Tab 1-3 Tab 1-3 Unit Operations and Processes used to Remove Constituents Found in Wastewater Constituent I Unit Operation or Process Suspended solids Screening, grit removal, sedimentation, high-rate clarification, flotation, depth filtration, surface filtration Biodegradable organics Aerobic suspended growth variations, aerobic attached growth variations, anaerobic suspended growth variations, anaerobic attached growth variations, lagoon variations, physical-chemical systems, chemical oxidation, advanced oxidation membrane filtration Nutrient-nitrogen Chemical oxidation, suspended growth nitrification and denitrification variations, fixed film nitrification and denitrification variations, air stripping, Nutrient-phosphorus Chemical treatment, biological removal Colloidal and dissolved Membranes, chemical treatment, carbon adsorption, ion exchange Volatile Air stripping, carbon adsorption, advanced oxidation compounds Odors Chemical scrubbers, carbon adsorption, biofliters, compost filters About 20 vears ago. biological nutrient removal(BNR) for the removal of nitrogen and phosphorus, was viewed as an innovative process for advanced wastewater treatment. Because of the extensive research into the mechanisms of bNR, the advantages of its use, and the number of placed into operations, nutrient removal, for all practical purpose become a part of conventional wastewater treatment. When compared to chemical treatment methods. BNR uses less chemical, reduces the production of waste solids. and has lower energy consumptions. Because of the importance of BNR in wastewater treatment, BNR is integrated into the discussion of theory, application, and design of biological treatment systems Land treatment processes, commonly termed"natural systems, "combine chemical, and biological treatment mechanisms and produce water with quality similar to or better than that from advanced wastewater treatment. Natural systems are used mainly with small treatment systems Current status Up until the late 1980s. conventional secondary treatment was the most common methods of treatment for the removal of BOD and TSS. In the United States, nutrients removal was used in special circumstances. uch as in the great Lakes area where sensitive nutrient-related water quality conditions were identified Because of nutrient enrichment that has led to eutrophication and degradation( due in part to point source discharges), nutrient removal processes have evolved and now are used extensively in other areas as well The municipal wastewater treatment enterprise is composed of over 16.000 plants that are used to treat a total flow of about 1400 cubic meters per second. Approximately 92 per cent of the total existing flow is handled by plants having capacity of 0.044 m/s and larger. Nearly one-half of the present design capacity is situated in plants providing greater than secondary treatment. In the last 10 vears. many plants have been designed using BNR. Effluent filtration has also been installed the effectiveness of disinfection especially for ultraviolet (UV disinfection systems. because(1) the removal of larger particles of suspended solids that harbor bacteria enhances the reduction in coliform bacteria and(2) the reduction of turbidity improves the transmittance of uv light Effluent reuse 1-5
1-5 Primary Removal of a portion of the suspended solids and organic matter from the wastewater Advanced Primary Enhanced removal of suspended solids and organic matter from the wastewater. Typically accomplished by chemical addition or filtration Secondary Removal of biodegradable organics, suspended solids. Disinfection is also typically included in the definition of conventional secondary treatment Tertiary Removal of residual suspended solids, usually by granular medium filtration or microscreens. Disinfection is also typically a part of tertiary treatment. Nutrient removal is often included in this definition. Advanced Removal of dissolved and suspended materials remaining after normal biological treatment when required for various water reuse applications A listing of unit operations and processes used for the removal of major constituents found in wastewater is presented in Tab 1-3. Tab 1-3 Unit Operations and Processes used to Remove Constituents Found in Wastewater Constituent Unit Operation or Process Suspended solids Screening, grit removal, sedimentation, high-rate clarification, flotation, chemical precipitation, depth filtration, surface filtration Biodegradable organics Aerobic suspended growth variations, aerobic attached growth variations, anaerobic suspended growth variations, anaerobic attached growth variations, lagoon variations, physical-chemical systems, chemical oxidation, advanced oxidation, membrane filtration Nutrient-nitrogen Chemical oxidation, suspended growth nitrification and denitrification variations, fixed film nitrification and denitrification variations, air stripping, ion exchange Nutrient-phosphorus Chemical treatment, biological removal Pathogens Chlorine compounds, chlorine dioxide, ozone, UV radiation Colloidal and dissolved solids Membranes, chemical treatment, carbon adsorption, ion exchange Volatile organic compounds Air stripping, carbon adsorption, advanced oxidation Odors Chemical scrubbers, carbon adsorption, biofliters, compost filters About 20 years ago, biological nutrient removal (BNR) for the removal of nitrogen and phosphorus, was viewed as an innovative process for advanced wastewater treatment. Because of the extensive research into the mechanisms of BNR, the advantages of its use, and the number of BNR systems that have been placed into operations, nutrient removal, for all practical purposes, has become a part of conventional wastewater treatment. When compared to chemical treatment methods, BNR uses less chemical, reduces the production of waste solids, and has lower energy consumptions. Because of the importance of BNR in wastewater treatment, BNR is integrated into the discussion of theory, application, and design of biological treatment systems. Land treatment processes, commonly termed “natural systems,” combine chemical, and biological treatment mechanisms and produce water with quality similar to or better than that from advanced wastewater treatment. Natural systems are used mainly with small treatment systems. Current Status Up until the late 1980s, conventional secondary treatment was the most common methods of treatment for the removal of BOD and TSS. In the United States, nutrients removal was used in special circumstances, such as in the Great Lakes area where sensitive nutrient-related water quality conditions were identified. Because of nutrient enrichment that has led to eutrophication and degradation (due in part to point source discharges), nutrient removal processes have evolved and now are used extensively in other areas as well. The municipal wastewater treatment enterprise is composed of over 16,000 plants that are used to treat a total flow of about 1400 cubic meters per second. Approximately 92 per cent of the total existing flow is handled by plants having capacity of 0.044 m3 /s and larger.Nearly one-half of the present design capacity is situated in plants providing greater than secondary treatment. In the last 10 years, many plants have been designed using BNR. Effluent filtration has also been installed where the removal of residual suspended solids is required. Filtration is especially effective in improving the effectiveness of disinfection, especially for ultraviolet (UV) disinfection systems, because (1) the removal of larger particles of suspended solids that harbor bacteria enhances the reduction in coliform bacteria and (2) the reduction of turbidity improves the transmittance of UV light. Effluent reuse
systems, except for many that are used for agricultural irrigation, almost always employ filtration New directions and concerns in wastewater treatment are evident in various specific areas. The changing be treated, emerging health and environmental industrial was stes, and the impact of new regulations, are among the most important. Further, other important concerns include ng infrastructure.(2) new methods of process sis and control (3 treatment plant performance and reliabil ity, (4)wastewater disinfection, (5) combined sewer overflows. (6) impacts of stormwater and sanitary overflows and nonpdint sources of pollution, (7) separate treatment of return flows,(8)odor control and the control of VOC emissions, and (9) retrofitting and Some of the problems that have to be addressed in the United States deal with renewal of the aging wastewater collection infrastructure and upgrading of treatment plants. Issues include replacement of leaking and undersized sewers. control and treatment of overflows from sanitary and combined collection systems, control of nonpoint discharges, and upgrading treatment systems to achieve higher removal levels of specific constituents ollection systems. particularly those in the older cities in the eastern and midwestern United States, are older than the treatment plants. Sewers constructed of brick and vitrified clay with mortar ioints. for example, are still used to carry sanitary wastewater and stormwater. Because of the age of the pipes and ancillary structures, the types of materials and methods of construction, and lack of repair, leakage is common. Leakage is in the form of both infiltration and inflow where water enters the collection system, and exfil tration where water leaves the pipe. In the former case, extraneous water has to be collected and treated, and oftentimes may overflow before treatment, especially during wet weather. In the latter case, exfiltration causes untreated wastewater to enter the groundwater and/or migrate to nearby surface water bodies. It is interesting to note that while the standar r treatment have increase significantlv, comparatively little or no attention has been focused on the discharge of untreated wastewater from sewers through exfiltration. In the future, however, leaking sewers are expected to become a major concern and will require correction Because of the changing characteristics of the wastewater, studies of wastewater treatability are increasing. especially with reference to the treatment of specific constituents. Such studies are especially important where new treatment processes are being considered. Therefore, the engineer must understand the general approach and methodology involved in:(D assessing the treatability of a wastewater(domestic or industrial).(2) conducting laboratory and pilot plant studies, and(3) translating experimental data into Computational fluid dynamics (CFD) computer-based computational methods for solving fundamental equations of fluid dynamics (ie, continuity, momentum, and energy), is now being used to improve and optimize the hydraulic performance of wastewater treatment facilities. Applications of CFD include the design of new systems or the optimization of systems such as vortex separators, mixing tanks. sedimentation tanks. dissolved-air flotation units. and chlorine contact tanks to reduce or eliminate dead zones and short circuiting Improved UV disinfection systems are being designed using CFD. One of the main advantages of CFD is simulating a range of operating conditions to evaluate performance before designs and operating changes are finalized. Another advantage is that dynamic models can be integrated with the process control system to optimize ongoing operation Important factors in process selection and design are treatment plant performance and reliability in meeting permit requirements. Because wastewater treatment effluent quality is variable because of varving organic loads changing environmental conditions. and new industrial discharges it is necessary to design the treatment system to produce effluent concentrations equal to or less than the limits prescribed by the maintained such as in reuse applications. On-line monitoring of critical parameters such as total organic carbon(TOC), transmissivity, turbidity, and dissolved oxygen is necessary for building a database and for improving process control, Chlorine residual monitoring is useful for dosage control, and pH monitoring assists in controlling nitrification systems e defined as the probability that a system can meet established performance criteria consistently over extended periods of time. Two components of reliabilitv. the inherent reliability of the process and mechanical reliability will be discussed. As improved microbiological techniques are developed, it will be possible to optimize the disinfection process The need to conserve energy and resources is fundamental to all aspects of wastewater collection. important parts of treatment plant design and operation as significant savings can be realized by selecting 1-6
1-6 systems,except for many that are used for agricultural irrigation, almost always employ filtration. New directions and concerns in wastewater treatment are evident in various specific areas . The changing nature of the wastewater to be treated, emerging health and environmental concerns, the problem of industrial wastes, and the impact of new regulations, are among the most important. Further, other important concerns include: (1) aging infrastructure, (2) new methods of process analysis and control, (3) treatment plant performance and reliability, (4) wastewater disinfection, (5) combined sewer overflows, (6) impacts of stormwater and sanitary overflows and nonpdint sources of pollution, (7) separate treatment of return flows, (8) odor control and the control of VOC emissions, and (9) retrofitting and upgrading wastewater treatment plants. Some of the problems that have to be addressed in the United States deal with renewal of the aging wastewater collection infrastructure and upgrading of treatment plants. Issues include repair and replacement of leaking and undersized sewers, control and treatment of overflows from sanitary and combined collection systems, control of nonpoint discharges, and upgrading treatment systems to achieve higher removal levels of specific constituents. Portions of the collection systems, particularly those in the older cities in the eastern and midwestern United States, are older than the treatment plants. Sewers constructed of brick and vitrified clay with mortar joints, for example, are still used to carry sanitary wastewater and stormwater. Because of the age of the pipes and ancillary structures, the types of materials and methods of construction, and lack of repair, leakage is common. Leakage is in the form of both infiltration and inflow where water enters the collection system, and exfiltration where water leaves the pipe. In the former case, extraneous water has to be collected and treated, and oftentimes may overflow before treatment, especially during wet weather. In the latter case, exfiltration causes untreated wastewater to enter the groundwater and/or migrate to nearby surface water bodies. It is interesting to note that while the standards for treatment have increased significantly, comparatively little or no attention has been focused on the discharge of untreated wastewater from sewers through exfiltration. In the future, however, leaking sewers are expected to become a major concern and will require correction. Because of the changing characteristics of the wastewater, studies of wastewater treatability are increasing, especially with reference to the treatment of specific constituents. Such studies are especially important where new treatment processes are being considered. Therefore, the engineer must understand the general approach and methodology involved in: (1) assessing the treatability of a wastewater (domestic or industrial), (2) conducting laboratory and pilot plant studies, and (3) translating experimental data into design parameters. Computational fluid dynamics (CFD), computer-based computational methods for solving the fundamental equations of fluid dynamics (i.e., continuity, momentum, and energy), is now being used to improve and optimize the hydraulic performance of wastewater treatment facilities. Applications of CFD include the design of new systems or the optimization of systems such as vortex separators, mixing tanks, sedimentation tanks, dissolved-air flotation units, and chlorine contact tanks to reduce or eliminate dead zones and short circuiting. Improved UV disinfection systems are being designed using CFD. One of the main advantages of CFD is simulating a range of operating conditions to evaluate performance before designs and operating changes are finalized. Another advantage is that dynamic models can be integrated with the process control system to optimize ongoing operation. Important factors in process selection and design are treatment plant performance and reliability in meeting permit requirements. Because wastewater treatment effluent quality is variable because of varying organic loads changing environmental conditions, and new industrial discharges, it is necessary to design the treatment system to produce effluent concentrations equal to or less than the limits prescribed by the discharge permit. Reliability is especially important where critical water quality parameters have to be maintained such as in reuse applications. On-line monitoring of critical parameters such as total organic carbon (TOC), transmissivity, turbidity, and dissolved oxygen is necessary for building a database and for improving process control. Chlorine residual monitoring is useful for dosage control,and pH monitoring assists in controlling nitrification systems. Treatment plant reliability can be defined as the probability that a system can meet established performance criteria consistently over extended periods of time. Two components of reliability, the inherent reliability of the process and mechanical reliability, will be discussed. As improved microbiological techniques are developed, it will be possible to optimize the disinfection process. The need to conserve energy and resources is fundamental to all aspects of wastewater collection, treatment, and reuse. Operation and maintenance costs are extremely important to operating agencies because these costs are funded totally with local moneys. Detailed energy analyses and audits are important parts of treatment plant design and operation as significant savings can be realized by selecting
energv-efficient processes and equipment. Large amounts of electricity are used for aeration that is needed for biological treatment. Tvpicallv. about one-half of the entire plant electricity usage is for aeration. In the design of wastewater treatment plants power use can be minimized by paying more careful attention to plant siting, selecting energy-efficient equipment, and designing facilities to recover energy for in-plant Changes in regulations and the development of new technologies have affected the design of disinfection systems. Gene probes are now being used to identify where specific groups of organisms are found in r particle-associated). Historically, chlorine has been the disinfectant of choice for wastewater. With the increasing number of permits requiring low nondetectable amounts of chlorine residual in treated effluents. dechlorination facilities have had to be added, or chlorination systems have been replaced by alternative disinfection systems such as ultraviolet (UV) radiation. Concerns about chemical safety have also affected design considerations of chlorination ns. Improvements that have been made in UV lamp and ballast design within the past 10 years have improved significantly the performance and reliability of UV disinfection systems Effective guidelines have also been developed for the application and design of UV systems. Capital and operating costs have also been lowered. It is anticipated that the application of UV for treated drinking water and for stormwater will continue to increase in the future. Because Uv produces essentially no troublesome byproducts and is also effective in the reduction of NDMA and other related compounds, its use for disinfection is further enhanced as compared to chlorine compound Overflows from combined sewer and sanitary sewer collection systems have been recognized as difficul problems requiring solution especially for many of the older cities in the United States. The problem has become more critical as greater development changes the amount and characteristics of stormwater runoff and increases the channelization of runoff into storm, combined, and sanitary collection systems Combined systems carry a mixture of wastewater and stormwater runoff and, when the capacity of the interceptors is reached. overflows occur to the receiving waters. Large overflows can impact receiving water quality and can prevent attainment of mandated standards. Recreational beach closings and shellfish bed closures have been attributed to CSOs( Combined System Overflow). Federal regulations for CSOs e still under development and have not been issued at present A combination of factors has resulted in the release of untreated wastewater from parts of sanitary collection systems. These releases are termed sanitary system overflows(SSOs). The SSOs may be caused by(1) the entrance of excessive amounts of stormwater, (2) blockages, or (3)structural, mechanical,or electrical failures. Many overflows result from aging collection systems that have not received adequate upgrades, maintenance, and repair. The U.S. EPa has estimated that at least 40,000 overflows per vear occur from sanitary collection systems. The untreated wastewater of these overflows represents threats to public health and the environment. The U.S. EPa is proposing to clarify and expand permit requirements for municipal sanitary collection systems under the Clean Water Act that will result in reducing the frequency and occurrence of Ssos(U.S EPA 2001). The U.S. EPA estimates that nearly $45 billion is required for constructing facilities for controlling CSOs and SSOs in the United States(U.S. EPA, 1997a) The effects of pollution from nonpoint sources are growing concerns as evidenced by the outbreak of gastrointestinal illness in Milwaukee traced to the oocysts of Crytosporidium parum, and the occurrence of Pfiesteria piscicida in the waters of Maryland and North Carolina. Pfiesteria is a form of algae that is very toxic to fish life. Runoff from pastures and feedlots has been attributed as a potential factor that triggers the effects of these microorganisms Perhaps one of the significant future developments in wastewater treatment will be the provision of separate facilities for treating return flows from biosolids and other processing facilities. Treatment of return flows will be especially important where low levels of nitrogen are to be achieved in the treated effluent. Separate treatment facilities may include (1)steam stripping for removal of ammonia from biosolids return flows. now typically routed to the plant headworks:(2)high-rate sedimentation for removing fine and difficult-to-settle colloidal material that also shields bacteria from disinfection: ()flotation and high-rate sedimentation for treating to reduce solids loading on metals removal by chemical precipitation to meet more stringent discharge requirements. The specific treatment sy used will depend on the will impact the wastewater treatment proc The control of odors and in particular the control of 7
1-7 energy-efficient processes and equipment. Large amounts of electricity are used for aeration that is needed for biological treatment. Typically, about one-half of the entire plant electricity usage is for aeration. In the design of wastewater treatment plants power use can be minimized by paying more careful attention to plant siting, selecting energy-efficient equipment, and designing facilities to recover energy for in-plant use. Changes in regulations and the development of new technologies have affected the design of disinfection systems. Gene probes are now being used to identify where specific groups of organisms are found in treated secondary effluent (i.e., in suspension or particle-associated). Historically, chlorine has been the disinfectant of choice for wastewater. With the increasing number of permits requiring low or nondetectable amounts of chlorine residual in treated effluents, dechlorination facilities have had to be added, or chlorination systems have been replaced by alternative disinfection systems such as ultraviolet (UV) radiation. Concerns about chemical safety have also affected design considerations of chlorination and dechlorination systems. Improvements that have been made in UV lamp and ballast design within the past 10 years have improved significantly the performance and reliability of UV disinfection systems. Effective guidelines have also been developed for the application and design of UV systems. Capital and operating costs have also been lowered. It is anticipated that the application of UV for treated drinking water and for stormwater will continue to increase in the future. Because UV produces essentially no troublesome byproducts and is also effective in the reduction of NDMA and other related compounds, its use for disinfection is further enhanced as compared to chlorine compounds. Overflows from combined sewer and sanitary sewer collection systems have been recognized as difficult problems requiring solution, especially for many of the older cities in the United States. The problem has become more critical as greater development changes the amount and characteristics of stormwater runoff and increases the channelization of runoff into storm, combined, and sanitary collection systems. Combined systems carry a mixture of wastewater and stormwater runoff and, when the capacity of the interceptors is reached, overflows occur to the receiving waters. Large overflows can impact receiving water quality and can prevent attainment of mandated standards. Recreational beach closings and shellfish bed closures have been attributed to CSOs (Combined System Overflow). Federal regulations for CSOs are still under development and have not been issued at present. A combination of factors has resulted in the release of untreated wastewater from parts of sanitary collection systems. These releases are termed sanitary system overflows (SSOs). The SSOs may be caused by (1) the entrance of excessive amounts of stormwater, (2) blockages, or (3) structural, mechanical, or electrical failures. Many overflows result from aging collection systems that have not received adequate upgrades, maintenance, and repair. The U.S. EPA has estimated that at least 40,000 overflows per year occur from sanitary collection systems. The untreated wastewater of these overflows represents threats to public health and the environment. The U.S. EPA is proposing to clarify and expand permit requirements for municipal sanitary collection systems under the Clean Water Act that will result in reducing the frequency and occurrence of SSOs (U.S. EPA 2001). The U.S. EPA estimates that nearly $45 billion is required for constructing facilities for controlling CSOs and SSOs in the United States (U.S. EPA, 1997a). The effects of pollution from nonpoint sources are growing concerns as evidenced by the outbreak of gastrointestinal illness in Milwaukee traced to the oocysts of Crytosporidium parvum, and the occurrence of Pfiesteria piscicida in the waters of Maryland and North Carolina. Pfiesteria is a form of algae that is very toxic to fish life.Runoff from pastures and feedlots has been attributed as a potential factor that triggersthe effects of these microorganisms. Perhaps one of the significant future developments in wastewater treatment will be the provision of separate facilities for treating return flows from biosolids and other processing facilities. Treatment of return flows will be especially important where low levels of nitrogen are to be achieved in the treated effluent. Separate treatment facilities may include (1)steam stripping for removal of ammonia from biosolids return flows, now typically routed to the plant headworks; (2)high-rate sedimentation for removing fine and difficult-to-settle colloidal material that also shields bacteria from disinfection; (3)flotation and high-rate sedimentation for treating filter backwash water to reduce solids loading on the liquid treatment process; and (4)soluble heavy metals removal by chemical precipitation to meet more stringent discharge requirements. The specific treatment system used will depend on the constituents that will impact the wastewater treatment process. The control of odors and in particular the control of
hydrogen sulfide generation is of concern in collection systems and at treatment facilities The release of hydrogen sulfide to the atmosphere above sewers and at treatment plant headworks has occurred in a concrete sewers. headworks structures and equipment. and to the release of odors. The control of odors is of increasing environmental concern as residential and commercial development continues to existing treatment plant locations. Odor control facilities including covers for process units. special rentilation equipment, and treatment of odorous gases need to be integrated with treatment plant design Control of hydrogen sulfide is also fundamental to maintaining system reliability Fig 1-3 Facilities used for chemical treatment of odors from treatment facilities of vocs and vocs in wastewater has necessitated the covering of treatment plant headworks and facilities to treat the compounds before they are released. In some cases, improved industrial pretreatment has been constructed in the United States during the 1970s and 1980s when large sums of federal money were available for implementation of the CWA(Clean Water Act). Much of the quipment, now over 20 vears old. is reaching the end of its useful life and will need to be replaced. Process changes to mprove performance, meet stricter permit requirements and increase capacity will also be needed For these reasons, significant future efforts in the planning and design of wastewater treatment plants in the United States will be directed to modifying improving and expanding existing treatment facilities. Fewer completely new treatment plants will be constructed. In developing countries. opportunities for designing and building completely new facilities may be 1-4 UV lamps used for the disinfection of wastewater In the U.S. EPA Needs Assessment Survey, the total treatment plant design capacity projected to increase by about 15 percent over the next 20 to 30 vears During this period, the U.S. EPA estimates that approximately 2, 300 new plants may have to be built. most of which will be providing a level of treatment greater than secondary. The design capacity of plants providing greater than secondary treatment is expected to increase by 40 percent in ure(U.S. EPA 1997). Thus, it is clear that the future trends in wastewater treatment plant design will be for facilities providing higher levels of treatment Some of the innovative treatment methods being utilized in new and upgraded treatment facilities include vortex separators. high rate clarification, membrane bio-reactor pressure-driven membrane filtration and In recent years, numerous proprietary wastewater treatment processes have been developed that offer potential savings in construction and operation. This trend will likely continue, particularly where alternative treatment systems are evaluated or facilities are privatized. Privatization is generally defined as a public-private partnership in which the private partner arranges the finan operation of the treatment facilities. in some cases, the private partner may own the facilities. The reasons for privatization, however, go well beyond the possibility of installing proprietary processes. In the United States, the need for private financing appears to be the principal rationale for privatization, the need to preserve local control appears to be the leading pragmatic rationale against privatization 1-6 Wastewater Reclamation and reuse In many locations where the available supply of fresh water has become inadequate to meet water needs. it is clear that the once-used water collected from communities and municipalities must be viewed not as a waste to be disposed of but as a resource that must be reused. The concept of reuse is becoming accepted more widely as other parts of the country experience water shortages. The use of dual water systems. such 1-8
1-8 hydrogen sulfide generation is of concern in collection systems and at treatment facilities. The release of hydrogen sulfide to the atmosphere above sewers and at treatment plant headworks has occurred in a number of locations. The release of excess hydrogen sulfide has led to the accelerated corrosion of concrete sewers, headworks structures, and equipment, and to the release of odors. The control of odors is of increasing environmental concern as residential and commercial development continues to approach existing treatment plant locations. Odor control facilities including covers for process units, special ventilation equipment, and treatment of odorous gases need to be integrated with treatment plant design. Control of hydrogen sulfide is also fundamental to maintaining system reliability. Fig 1-3 Facilities used for chemical treatment of odors from treatment facilities The presence of VOCs and VTOCs in wastewater has also necessitated the covering of treatment plant headworks and primary treatment facilities and the installation of special facilities to treat the compounds before they are released. In some cases, improved industrial pretreatment has been employed to eliminate these compounds. Large numbers of wastewater treatment plants were constructed in the United States during the 1970s and 1980s when large sums of federal money were available for implementation of the CWA(Clean Water Act). Much of the equipment, now over 20 years old, is reaching the end of its useful life and will need to be replaced. Process changes to improve performance, meet stricter permit requirements, and increase capacity will also be needed. For these reasons, significant future efforts in the planning and design of wastewater treatment plants in the United States will be directed to modifying, improving, and expanding existing treatment facilities. Fewer completely new treatment plants will be constructed. In developing countries, opportunities for designing and building completely new facilities may be somewhat greater. Fig. 1-4 UV lamps used for the disinfection of wastewater In the U.S. EPA Needs Assessment Survey, the total treatment plant design capacity projected to increase by about 15 percent over the next 20 to 30 years. During this period, the U.S. EPA estimates that approximately 2,300 new plants may have to be built, most of which will be providing a level of treatment greater than secondary. The design capacity of plants providing greater than secondary treatment is expected to increase by 40 percent in the future (U.S. EPA, 1997). Thus, it is clear that the future trends in wastewater treatment plant design will be for facilities providing higher levels of treatment. Some of the innovative treatment methods being utilized in new and upgraded treatment facilities include vortex separators, high rate clarification, membrane bio-reactor, pressure-driven membrane filtration and UV lamps. In recent years, numerous proprietary wastewater treatment processes have been developed that offer potential savings in construction and operation. This trend will likely continue, particularly where alternative treatment systems are evaluated or facilities are privatized. Privatization is generally defined as a public-private partnership in which the private partner arranges the financing, design, building, and operation of the treatment facilities, in some cases, the private partner may own the facilities. The reasons for privatization, however, go well beyond the possibility of installing proprietary processes. In the United States, the need for private financing appears to be the principal rationale for privatization; the need to preserve local control appears to be the leading pragmatic rationale against privatization. 1-6 Wastewater Reclamation and Reuse In many locations where the available supply of fresh water has become inadequate to meet water needs, it is clear that the once-used water collected from communities and municipalities must be viewed not as a waste to be disposed of but as a resource that must be reused. The concept of reuse is becoming accepted more widely as other parts of the country experience water shortages. The use of dual water systems, such
as now used in St. Petersburg in Florida and Rancho Viejo in California, is expected to increase in the future. In both loca of th an important electriologies being te reclamation. Ir lessen health ri 1-7 Biosolids an continues to be one Wastewater sol metals and pa biosolids. Fur home use is p customarily ir the incre concentrat ance and economic palities continues to
1-9 as now used in St. Petersburg in Florida and Rancho Viejo in California, is expected to increase in the future. In both locations, treated effluent is used for landscape watering and other nonpotable uses. Most of the reuse of wastewater occurs in the arid and semiarid western and southwestern states of the United States; however, the number of reuse projects is increasing in the south especially in Florida and South Carolina. Because of health and safety concerns, water reuse applications are mostly restricted to nonpotable uses such as landscape and agricultural irrigation. In a report by the National Research Council (1998), it was concluded that indirect potable reuse of reclaimed water (introducing reclaimed water to augment a potable water source before treatment) is viable. The report also stated that direct potable reuse (introducing reclaimed water directly into a water distribution system) was not practicable. Because of the concerns about potential health effects associated with the reclaimed water reuse, plans are proceeding slowly about expanding reuse beyond agricultural and landscape irrigation, groundwater recharge for repelling saltwater intrusion, and nonpotable industrial uses (e.g., boiler water and cooling water). Many of the concerns mentioned in the National Research Council (NRC, 1998) report regarding potential microbial and chemical contamination of water supplies also apply to water sources that receive incidental or unplanned wastewater discharges. A number of communities use water sources that contain a significant wastewater component. Even though these sources, after treatment, meet current drinking water standards, the growing knowledge of the potential impacts of new trace contaminants raises concern. Conventional technologies for both water and wastewater treatment may be incapable of reducing the levels of trace contaminants below where they are not considered as a potential threat to public health. Therefore. new technologies that offer significantly improved levels of treatment or constituent reduction need to be tested and evaluated. Where indirect potable reuse is considered, risk assessment also becomes an important component of a water reuse investigation. Technologies that are suitable for water reuse applications include membranes (pressure driven, electrically driven, and membrane bioreactors), carbon adsorption, advanced oxidation, ion exchange, and air stripping. Membranes are most significant developments as new products are now available for a number of treatment applications. Membranes had been limited previously to desalination, but they are being tested increasingly for wastewater applications to produce high-quality treated effluent suitable for reclamation. Increased levels of contaminant removal not only enhance the product for reuse but also lessen health risks. As indirect potable reuse intensifies to augment existing water supplies, membranes are expected to be one of the predominant treatment technologies. 1-7 Biosolids and Residuals Management The management of the solids and concentrated contaminants removed by treatment has been and continues to be one of the most difficult and expensive problems in the field of wastewater engineering. Wastewater solids are organic products that can be used beneficially after stabilization by processes such as anaerobic digestion and composting. With the advent of regulations that encourage biosolids use, significant efforts have been directed to producing a "clean sludge" (Class A biosolids) that meets heavy metals and pathogen requirements and is suitable for land application. Regulations for Class B biosolids call for reduced density in pathogenic bacteria and enteric viruses, but not to the levels of Class A biosolids. Further, the application of Class B biosolids to land is strictly regulated, and distribution for home use is prohibited. Other treatment plant residuals such as grit and screenings have to be rendered suitable for disposal, customarily in landfills. Landfills usually require some form of dewatering to limit moisture content. With the increased use of membranes, especially in wastewater reuse applications, a new type of residual, brine concentrate, requires further processing and disposal. Solar evaporation ponds and discharge to a saltwater environment are only viable in communities where suitable and environmental geography conditions prevail; brine concentration and residuals solidification are generally to complex and costly to implement. Treatment technologies for solids processing have focused on traditional methods such as thickening, stabilization, dewatering, and drying. Evolution in the technologies has not occurred as rapidly as in liquid treatment processes, but some significant improvements have occurred. Centrifuges that produce a sludge cake with higher solids content, egg-shaped digesters that improve operation, and dryers that minimize water content are just a few examples of products that have come into use in recent years. The developments are largely driven by the need to produce biosolids that are clean, have less volume, and can be used beneficially. Landfills still continue to be used extensively for the disposal of treatment plant solids, either in sludge-only monofills or with municipal solid waste. The number and capacity of landfills, however, have been reduced, and new landfill locations that meet public and regulatory acceptance and economic requirements are increasingly difficult to find. Incineration of solids by large municipalities continues to
be practiced, but incineration operation and emission control are subiect to greater regulatory restriction and adverse public scrutiny. Alternatives to landfills and incineration include land application of liquid or dried biosolids and composting for distribution and marketing. Land application of biosolids is used extensively to reclaim marginal land for productive uses and to utilize nutrient content in the biosolids Composting, although a more expensive alternative, is a means of stabilizing and distributing biosolids for use as a soil amendment. Alkaline stabilization of biosolids for land applications also used but to a lesser extent Over the last 30 years, the principal focus in wastewater engineering has been on improving the quality of treated effluent through the construction of secondary and advanced wastewater treatment plants. With improved treatment methods, higher levels of treatment must be provided not only for conventiona wastewater constituents but also for the removal of specific compounds such as nutrients and heavy metals. A byproduct of these efforts has been the increased generation of solids and biosolids per person In many cases, the increase in solids production clearly taxes the capacity of existing solids processing and dispos In addition to the shear volume of solids that has to be handled and processed, management options continue to be reduced through stricter regulations. Limitations that affect options are: (1)landfill sites are becoming more difficult to find and have permitted, (2 )air emissions from incinerators are more closely regulated, and()new requirements for the land application of biosolids have been instituted. In large urban areas, haul distances to landfill or land application sites have significantly affected the cost of solids rocessing and disposal. Few new incinerators are being planned because of difficulties in finding suitable sites and obtaining permits. Emission control regulations of the Clean Air Act also require the installation More communities are looking toward (1)producing Class a biosolids to improve beneficial reuse opportunities or(2)implementing a form of volume reduction, thus lessening the requirements for disposal The continuing search for better methods of solids processing. disposal, and reuse will remain as one of the highest priorities in the future Additionally, developing meaningful dialogue with the public about health and environmental effects will continue to be very important New solids processing sy stems have not been developed as rapidly as liquid unit operations and processes Anaerobic digestion remains the principal process for the stabilization of solids. Egg-shaped digesters. developed in Europe for anaerobic digestion, are being used more extensively in the United States because of advantages of easier operation. lower operation and maintenance costs, and, in some cases, increased eases the prod as). Other developments in anaerobic and aerobic digestion include temperature autothermal aerobic digestion(ATAD). another process developed in Europe. These processes offer dvantages of improved volatile solids destruction and the production of stabilized biosolids that meet Class a requirements High solids centrifuges and heat dryers are expected to be used more extensively. High solids centrifuges extract a greater percentage of the water in liquid sludge, thus providing a dryer cake. Improved dewatering nor only reduces the volume of solids requiring further processing and disposal, but allows composting or subsequent drying to be performed more efficiently. Heat drying provides further volume reduction and improves the quality of the product for potential commercial marketing Fig. 1-5 Egg-shaped digesters used for the anaerobic treatment of biosolids
1-10 be practiced, but incineration operation and emission control are subject to greater regulatory restriction and adverse public scrutiny. Alternatives to landfills and incineration include land application of liquid or dried biosolids and composting for distribution and marketing. Land application of biosolids is used extensively to reclaim marginal land for productive uses and to utilize nutrient content in the biosolids. Composting, although a more expensive alternative, is a means of stabilizing and distributing biosolids for use as a soil amendment. Alkaline stabilization of biosolids for land applications also used but to a lesser extent. Over the last 30 years, the principal focus in wastewater engineering has been on improving the quality of treated effluent through the construction of secondary and advanced wastewater treatment plants. With improved treatment methods, higher levels of treatment must be provided not only for conventional wastewater constituents but also for the removal of specific compounds such as nutrients and heavy metals. A byproduct of these efforts has been the increased generation of solids and biosolids per person served by a municipal wastewater system. In many cases, the increase in solids production clearly taxes the capacity of existing solids processing and disposal methods. In addition to the shear volume of solids that has to be handled and processed, management options continue to be reduced through stricter regulations. Limitations that affect options are: (1) landfill sites are becoming more difficult to find and have permitted, (2)air emissions from incinerators are more closely regulated, and (3)new requirements for the land application of biosolids have been instituted. In large urban areas, haul distances to landfill or land application sites have significantly affected the cost of solids processing and disposal. Few new incinerators are being planned because of difficulties in finding suitable sites and obtaining permits. Emission control regulations of the Clean Air Act also require the installation of complex and expensive pollution control equipment. More communities are looking toward (1) producing Class A biosolids to improve beneficial reuse opportunities or (2)implementing a form of volume reduction, thus lessening the requirements for disposal. The continuing search for better methods of solids processing, disposal, and reuse will remain as one of the highest priorities in the future. Additionally, developing meaningful dialogue with the public about health and environmental effects will continue to be very important. New solids processing systems have not been developed as rapidly as liquid unit operations and processes. Anaerobic digestion remains the principal process for the stabilization of solids. Egg-shaped digesters, developed in Europe for anaerobic digestion, are being used more extensively in the United States because of advantages of easier operation, lower operation and maintenance costs, and, in some cases, increased volatile solids destruction (which also increases the production of reusable methane gas). Other developments in anaerobic and aerobic digestion include temperature-phased anaerobic digestion and autothermal aerobic digestion (ATAD),another process developed in Europe. These processes offer advantages of improved volatile solids destruction and the production of stabilized biosolids that meet Class A requirements. High solids centrifuges and heat dryers are expected to be used more extensively. High solids centrifuges extract a greater percentage of the water in liquid sludge, thus providing a dryer cake. Improved dewatering nor only reduces the volume of solids requiring further processing and disposal, but allows composting or subsequent drying to be performed more efficiently. Heat drying provides further volume reduction and improves the quality of the product for potential commercial marketing. Fig. 1-5 Egg-shaped digesters used for the anaerobic treatment of biosolids