北京化工大学：《材料导论》课程阅读材料（无极非金属）Silicon-based_oxynitride_and_nitride_phosphors_for_white_LEDs_review.pdf_大学文库

Science and Technology of Advanced Materials ] (]]]]) ]]]–]]] Review Silicon-based oxynitride and nitride phosphors for white LEDs—A review Rong-Jun Xie, Naoto Hirosaki Nitride Particle Group, Nano Ceramics Center, National Institute for Materials Science, Namiki 1-1, Tsukuba, Ibaraki 305-0044, Japan Received 11 June 2007; received in revised form 25 July 2007; accepted 27 August 2007 Abstract As a novel class of inorganic phosphors, oxynitride and nitride luminescent materials have received considerable attention because of their potential applications in solid-state lightings and displays. In this review we focus on recent developments in the preparation, crystal structure, luminescence and applications of silicon-based oxynitride and nitride phosphors for white light-emitting diodes (LEDs). The structures of silicon-based oxynitrides and nitrides (i.e., nitridosilicates, nitridoaluminosilicates, oxonitridosilicates, oxonitridoaluminosilicates, and sialons) are generally built up of networks of crosslinking SiN4 tetrahedra. This is anticipated to significantly lower the excited state of the 5d electrons of doped rare-earth elements due to large crystal-field splitting and a strong nephelauxetic effect. This enables the silicon-based oxynitride and nitride phosphors to have a broad excitation band extending from the ultraviolet to visible-light range, and thus strongly absorb blue-to-green light. The structural versatility of oxynitride and nitride phosphors makes it possible to attain all the emission colors of blue, green, yellow, and red; thus, they are suitable for use in white LEDs. This novel class of phosphors has demonstrated its superior suitability for use in white LEDs and can be used in bichromatic or multichromatic LEDs with excellent properties of high luminous efficacy, high chromatic stability, a wide range of white light with adjustable correlated color temperatures (CCTs), and brilliant color-rendering properties. r 2007 NIMS and Elsevier Ltd. All rights reserved. Keywords: Oxynitride; Nitride; Phosphor; Luminescence; White LEDs; Sialon Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Classification and crystal chemistry of nitride compounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3. Structure and luminescence of silicon-based oxynitride and nitride phosphors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.1. Blue-emitting phosphors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.2. Green-emitting phosphors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.3. Yellow-emitting phosphors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.4. Red-emitting phosphors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4. Synthesis of silicon-based oxynitride and nitride phosphors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.1. Solid-state reaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.2. Gas-reduction nitridation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.3. Carbothermal reduction and nitridation (CRN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5. Applications of oxynitride and nitride phosphors in white LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 6. Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 ARTICLE IN PRESS www.elsevier.com/locate/stam 1468-6996/$ - see front matter r 2007 NIMS and Elsevier Ltd. All rights reserved. doi:10.1016/j.stam.2007.08.005 Corresponding author. Tel.: +81 29 860 4312; fax: +81 29 851 3613. E-mail address: Xie.Rong-Jun@nims.go.jp (R.-J. Xie). Please cite this article as: R.-J. Xie, N. Hirosaki, Sci. Technol. Adv. Mater. (2007), doi:10.1016/j.stam.2007.08.005

ARTICLE IN PRESS 1.Introduction phosphors for LEDs,it is essential to modify existing on phosphors or to explore new host crystals for phosphors nitrid earth-doped III-V g nitride ena are associated with large energy losses that occu such as AIN,GaN, large Stokes shifts ntensively i operation of LEDs is based on spontaneous light emissior the luminescence of silicon-based oxynitride and nitride in semiconductors,which is due to the radiative recombi nation of excess el tron and [that are produce con N2 pres sure,an Sub the ly,the radi that they used as As a high-temperature structural materials;and (iv)the limited with conventional lamp dersta struct ures as a resul of th hav nsumption and pollution from fossil fuel power plants recent vears becar of their enc raging luminescent ]Currently,LEDs are widely used ndicators. rea properties (excitability blue light,high conversion quid de hts Io the of ful in the brighu and high otential for use i yhite I ED it is generally accepted that they [11-14.In this review,we discuss recent developments in replace conventional lamps for general lighting in the rare-earth-activated oxynitrid and nitride ding th phosphor ral ther are three methods of creating light in LEDs:(i)using three individual monochromatic green and red colors;(ii)combining an olet (UV) and red pho 2.Cla sification and crystal chemistry of nitride compound nhosnhors 2 In the latter two case Nitride compounds are a large family of nitrogen- phosphorsre used as downconversion luminescent mat containing that are formed by combining sourc hors in ED electro J:0 for pho for p e in I EDs ar (in chemical characteristics of the bonds between nitr en and c phosphors in cathode-ray Meta llic nitrides. such as TiN 254 aps are are u by the form of M-N.with M being an alkali-.alkaline- addition,they should also have the following ch cte metal,and/or rare arth metal;examples include Li; stabilit n as B. AIN.GaN y thermal a ith IB-VB om the size(5-20um片and(w）appr phor ut white be co ed as host lattices for phosphors because the (Y1 ol an mn orthosilicates 3.aluminates 5 and sulfides 5.6]have either electrical or ionic conductors and both have narrow d in white LEDs.How band the gaps.Furthermore,the covalent chemical bonding low a nit to a ene hlue i EDs On the other hand sulfide-hased phosphors e cited of the sd electrons of the activato thermally unstable and very sensitive to moisture,and thei (e.g..Eu Ce )[16-20].This results in long excitation/ nce degrades significantly unde ambient emi wave engths and low therma in conventiona ors usec nd CRTs Please cite this article as:R.Xie,N.Hirosaki Sci.Technol Adv.Mater.(2)doi:.1016/.00

1. Introduction Conventional incandescent or fluorescent lamps rely on either incandescence or discharge in gases. Both phenomena are associated with large energy losses that occur because of the high temperatures and large Stokes shifts involved. Light-emitting diodes (LEDs) using semiconductors offer an alternative method of illumination. The operation of LEDs is based on spontaneous light emission in semiconductors, which is due to the radiative recombination of excess electrons and holes [1] that are produced by the injection of current with small energy losses. Subsequently, the radiative recombination of the injected carriers may attain quantum yields close to unity. As a result, compared with conventional lamps, LED-based light sources have superior lifetime, efficiency, and reliability, which promise significant reductions in power consumption and pollution from fossil fuel power plants [1]. Currently, LEDs are widely used as indicators, rear lamps for vehicles, decorated lamps, backlights for cellular phones and liquid crystal displays, and small-area lighting. With advances in the brightness and color-rendering properties of LEDs, it is generally accepted that they will replace conventional lamps for general lighting in the near future. In general, there are three methods of creating white light in LEDs: (i) using three individual monochromatic LEDs with blue, green, and red colors; (ii) combining an ultraviolet (UV) LED with blue, green, and red phosphors; and (iii) using a blue LED to pump yellow or green and red phosphors [2]. In the latter two cases, appropriate phosphors are used as downconversion luminescent materials. The excitation sources used for phosphors in LEDs differ greatly from those of phosphors in conventional lighting. The excitation sources for phosphors in LEDs are UV (360–410 nm) or blue light (420–480 nm), whereas those for conventional inorganic phosphors in cathode-ray tubes (CRTs) or fluorescent lamps are electron beams or mercury gas (lem ¼ 254 nm). Therefore, the phosphors in LEDs should have high absorption of UV or blue light. In addition, they should also have the following characteristics: (i) high conversion efficiency; (ii) high stability against chemical, oxygen, carbon dioxide, and moisture; (iii) low thermal quenching; (iv) small and uniform particle size (5–20 mm); and (v) appropriate emission colors. The phosphor most commonly utilized in bichromatic white LEDs is the yellow-emitting (Y1aGda)3(Al1bGab) O12:Ce3+ (YAG:Ce)[1]. Other types of phosphor such as orthosilicates [3,4], aluminates [5], and sulfides [5,6] have also been used in white LEDs. However, most oxide-based phosphors have low absorption in the visible-light spectrum, making it impossible for them to be coupled with blue LEDs. On the other hand, sulfide-based phosphors are thermally unstable and very sensitive to moisture, and their luminescence degrades significantly under ambient atmosphere without a protective coating layer. Consequently, to solve these problems and develop high-performance phosphors for LEDs, it is essential to modify existing phosphors or to explore new host crystals for phosphors such as nitrides. Luminescence in rare-earth-doped III–V group nitrides such as AlN, GaN, InGaN, and AlInGaN has been intensively investigated because of their potential applications in blue-UV optoelectronic and microelectronic devices [7–10]. However, less attention has been paid to the luminescence of silicon-based oxynitride and nitride compounds, perhaps due to (i) their critical preparation conditions (high temperature, high N2 pressure, and airsensitive starting powders); (ii) the lack of general synthetic routes; (iii) the strong impression that they are used as high-temperature structural materials; and (iv) the limited understanding of their crystal structures as a result of the difficulties in crystal growth. Silicon-based oxynitride and nitride phosphors have received significant attention in recent years because of their encouraging luminescent properties (excitability by blue light, high conversion efficiency, and the possibility of full color emission), as well as their low thermal quenching, high chemical stability, and high potential for use in white LEDs [11–14]. In this review, we discuss recent developments in rare-earth-activated oxynitride and nitride phosphors, including their crystal structure, preparation, luminescent properties, and applications in white LEDs. 2. Classification and crystal chemistry of nitride compounds Nitride compounds are a large family of nitrogencontaining compounds that are formed by combining nitrogen with less electronegative elements. Generally, nitrides can be grouped into three types: (i) metallic, (ii) ionic, and (iii) covalent compounds, based on the chemical characteristics of the bonds between nitrogen and other elements [15]. Metallic nitrides, such as TiN, ZrN, VN, CrN, and FeN, are usually produced by combining nitrogen with transition metals. Ionic nitrides are usually of the form of M–N, with M being an alkali-, alkaline-earth metal, and/or rare-earth metal; examples include Li3N, Ca3N2, CeN, and LiMnN2. Covalent nitrides, such as BN, AlN, GaN, silicon nitride (Si3N4), and P3N5, are formed by combining nitrogen with IIIB–VB group metals. From the viewpoint of luminescent materials, covalent nitrides can be considered as host lattices for phosphors because they have the characteristics of an insulator or semiconductor and wide band gaps, whereas metallic and ionic nitrides are either electrical or ionic conductors and both have narrow band gaps. Furthermore, the covalent chemical bonding in nitrides gives rise to a strong nephelauxetic effect (i.e., electron cloud expansion), reducing the energy of the excited state of the 5d electrons of the activators (e.g., Eu2+, Ce3+) [16–20]. This results in long excitation/ emission wavelengths and low thermal quenching, which cannot be achieved in conventional phosphors used in lamps and CRTs. ARTICLE IN PRESS 2 R.-J. Xie, N. Hirosaki / Science and Technology of Advanced Materials ] (]]]]) ]]]–]]] Please cite this article as: R.-J. Xie, N. Hirosaki, Sci. Technol. Adv. Mater. (2007), doi:10.1016/j.stam.2007.08.005

ARTICLE IN PRESS R-J.Xle,N.Hirosaki/Sclence and Technology of Adeanced Materials() Alternatively.nitride com ounds can also be divided engineers.For rare-earth ions (ie..Eu2 and Ce)with the 5d electrons unshielded from the crystal field by the 5 ents i binary,(ii)ter (quaternary and 5p electrons wher in the excite te,the spe BN. and AIN not bary ent m asily d as hen a for phosphors in white LEDs because they do not have bond length,site size,crystal-field strength,etc.).Becaus of the higher formal charge of N compared with 7-10 The he nepe covalent nitride iicon-based nitride of gravity of the sd states is shifted to lower are interesting because of their unique and rigid crystal ab ty of s able environmen oxynitride earth ions to provide u ping c and emission wavelengths than their oxide Furthermore,the Stokes shift becomes smaller in a rigid the preparation and crysta silicon-base etwork of SIN tetrahedr tena sialons is formed by the integ tion of nit gen in silicates A variety of oxynitride and nitride materials with aluminosilicat Com with the romising umine nt prope erties have been discovered dly [1-1 9 3].In t of thes addition to these nitride compounds oxynitrides (i.e. oxon 3.1.Blue-emitting phosphors mbind with aluminum resp vely.Therefore.m to oxosilicate and red phosphors to create white light when UV or near structure: oxyni and t(NUV)LED is used.Although a large numbe omp hedra.The degree of condensation in the netw ork of Six nal degradation is a serious problem if they are used in tetrahedra is simply evaluated by the ratio 「44D. Ce s to b ging atom the ate oxynitr pho S ratio n a h indicates that nitrides have a high degree of condensatior white LEDs.In the following.three types of blue-emitting due to the fact the and he phospho atoms O: xyger 1 ides are generall connected with two(N thre Al)N.O was re atoms such as in BaSiN Sr Ba)[24,25 eque (spac rdin ted h (N.O) elements result in the extraordinary chemical and ther vielding an Al(Si.Al)(N,O)network (see Fig.1).The La stability of silicon-based oxynitride and nitride materials caCanmodhedntunncheiendhng re along the and lumings ence of silicon-based oxynitride and nitride phosphors et al.1]reported the luminescence of Ce+-doped JEM As shown in Fig 2,the emission spectrum ,sulfide of JEM:C tending nm nhors is at oxy The road excitatic m extending from 200 to 450m realizing white LEDs has greatly catalyzed the research and due to the 4f. .5d electronic transition of Ce Both ment of oxynitride and nitride pho spectra redshifted whe value Please cite this article as:R.Xie.N.Hirosaki,Sci.Technol.Adv.Mater .(2007.doi10.1016 j.stam2007.08.00

Alternatively, nitride compounds can also be divided into the following groups depending on the number of elements included: (i) binary, (ii) ternary, (iii) quaternary, and (iv) multinary. Binary covalent nitrides, such as GaN, BN, and AlN, cannot be easily considered as host lattices for phosphors in white LEDs because they do not have suitable crystal sites for activators [13], although some of them show interesting luminescence properties in thin-film form [7–10]. The ternary, quaternary, and multinary covalent nitride compounds, typically silicon-based nitrides, are interesting because of their unique and rigid crystal structures, availability of suitable crystal sites for activators, and their structural versatility, which enable the doping of rare-earth ions to provide useful photoluminescence. Schnick and coworkers [21–28] extensively investigated the preparation and crystal structures of silicon-based oxynitride and nitride compounds. A new class of materials consisting of nitridosilicates, nitridoaluminosilicates, and sialons is formed by the integration of nitrogen in silicates or aluminosilicates. Compared with the well-known oxosilicates, the newly developed nitrides exhibit a much wider range of structural complexity and flexibility, forming a large family of multiternary compounds. In addition to these nitride compounds, oxynitrides (i.e., oxonitridosilicates and oxonitridoaluminosilicates) are derived from oxosilicates and oxoaluminosilicates by exchanges of oxygen with nitrogen and of silicon with aluminum, respectively. Therefore, similar to oxosilicates, the structures of silicon-based oxynitride and nitride compounds are generally built up of highly condensed networks constructed from linked SiX4 (X=O, N) tetrahedra. The degree of condensation in the network of SiX4 tetrahedra is simply evaluated by the ratio of tetrahedral Si centers to bridging atoms X. In oxosilicates the Si:X ratio reaches a maximum of 0.5 in SiO2, while in nitrides the Si:X ratio may vary in a broad range of 0.25–0.75. This indicates that nitrides have a high degree of condensation due to the fact that the structural possibilities in oxosilicates are limited to terminal oxygen atoms and simple bridging O[2] atoms, whereas the nitrogen atoms in nitrides are generally connected with two (N[2]), three (N[3]), even four (N[4]) silicon atoms such as in BaSi7N10 [23] and MYbSi4N7 (M ¼ Sr, Ba) [24,25]. Consequently, the highly condensed SiN4-based networks and the high stability of the chemical bonding between the constituent elements result in the extraordinary chemical and thermal stability of silicon-based oxynitride and nitride materials. 3. Structure and luminescence of silicon-based oxynitride and nitride phosphors Compared with oxide-, boride-, sulfide-, or phosphatebased phosphors, the study of oxynitride and nitride phosphors is at a very early stage. The possibility of realizing white LEDs has greatly catalyzed the research and development of oxynitride and nitride phosphors, and they are receiving significant attention from both scientists and engineers. For rare-earth ions (i.e., Eu2+ and Ce3+) with the 5d electrons unshielded from the crystal field by the 5s and 5p electrons when in the excited state, the spectral properties are strongly affected by the surrounding environment (e.g., symmetry, covalence, coordination, bond length, site size, crystal-field strength, etc.). Because of the higher formal charge of N3 compared with O2 and the nephelauxetic effect (covalence), the crystal-field splitting of the 5d levels of rare earths is larger and the center of gravity of the 5d states is shifted to lower energies (i.e., longer wavelength) than in an analogous oxygen environment. Consequently, silicon-based oxynitride and nitride phosphors are anticipated to show longer excitation and emission wavelengths than their oxide counterparts. Furthermore, the Stokes shift becomes smaller in a rigid lattice with a more extended network of SiN4 tetrahedra. A small Stokes shift leads to high conversion efficiency and small thermal quenching of phosphors. A variety of oxynitride and nitride materials with promising luminescent properties have been discovered recently [11–14,16–19,29–43]. In this section, we will review the structure and luminescence of these rare-earth-doped oxynitride and nitride phosphors. 3.1. Blue-emitting phosphors A blue-emitting phosphor must be combined with green and red phosphors to create white light when UV or near ultraviolet (NUV) LED is used. Although a large number of oxide-based phosphors emit an intense blue color under UV or NUV light excitation, the high thermal quenching or thermal degradation is a serious problem if they are used in white LEDs (e.g., BaMgAl10O17:Eu2+ [44]). Ce3+- or Eu2+-activated oxynitride blue phosphors undergo little thermal degradation and have strong absorption of UV or NUV light, enabling them to be alternative candidates for white LEDs. In the following, three types of blue-emitting oxynitride phosphor (i.e., LaAl(Si6zAlz)N10zOz:Ce3+, a-sialon:Ce3+, and (Y,La)-Si–O–N:Ce3+) will be described. The preparation and crystal structure of a JEM phase with chemical formula LaAl(Si6zAlz)N10zOz was reported by Grins et al. [45]. JEM has an orthorhombic structure (space group Pbcn) with a ¼ 9.4303 A˚ , b ¼ 9.7689 A˚ , and c ¼ 8.9386 A˚ . The Al atoms and (Si, Al) atoms are tetrahedrally coordinated by (N, O) atoms, yielding an Al(Si,Al)6(N,O)10 3 network (see Fig. 1). The La atoms are accommodated in tunnels extending along the [0 0 1] direction and are irregularly coordinated by seven (N, O) atoms at an average distance of 2.70 A˚ . Hirosaki et al. [11] reported the luminescence of Ce3+-doped JEM. As shown in Fig. 2, the emission spectrum of JEM:Ce3+ displays a broad band extending from 400 to 700 nm under 368 nm excitation, with a peak located at 475 nm. The broad excitation spectrum extending from 200 to 450 nm is due to the 4f-5d electronic transition of Ce3+. Both spectra are redshifted when the concentration of Ce3+ or the z value increases, enabling this blue phosphor to be ARTICLE IN PRESS R.-J. Xie, N. Hirosaki / Science and Technology of Advanced Materials ] (]]]]) ]]]–]]] 3 Please cite this article as: R.-J. Xie, N. Hirosaki, Sci. Technol. Adv. Mater. (2007), doi:10.1016/j.stam.2007.08.005

excited efficiently by UV (370–400 nm) or NUV (400–410 nm) LEDs. a-Sialon is a solid solution of a-Si3N4 and is formed by the partial replacement of Si–N bonds with Al–N and Al–O bonds. The general formula of a-sialon, consisting of four ‘‘Si3N4’’ units, can be given as MxSi12mn Alm+nOnN16n (x is the solubility of the M metal) [46–48], where m and n are the numbers of Al–N and Al–O bonds substituting for Si–N bonds, respectively. The charge discrepancy caused by the substitution is compensated for by the introduction of the M cations including Li+, Mg2+, Ca2+, Y3+, and some lanthanides. It has a hexagonal crystal structure and the P31c space group. In the structure of a-sialon, the M cations occupy the interstitial sites and are coordinated by seven (N, O) anions [49]. The crystal structure is shown in Fig. 3. The Ce3+-activated a-sialon (Ca0.898Ce0.068Si9Al3ON15) shows blue emission, as shown in Fig. 4. The emission spectrum, centered at 495 nm, extends from 400 to 650 nm upon 389 nm excitation. The peak emission wavelength is redshifted from 485 to 503 nm when the Ce concentration increases from 5 to 25 mol% [29,30]. Moreover, the emission of a-sialon:Ce3+ can also be tuned by varying the values of m and n. The excitation spectrum shows a broad band with a peak located at 389 nm, which closely matches the emission wavelengths of UV or NUV LEDs. There are several compounds in Y–Si–O–N and La– Si–O–N systems, and their luminescence spectra have been reported recently [17,31]. Van Krevel et al. [17] investigated the luminescent properties of Ce3+-doped Y–Si–O–N oxynitride compounds. Generally, these compounds emit a blue color with a peak emission wavelength of 400–500 nm and show maximum excitation bands at ARTICLE IN PRESS Fig. 2. Excitation and emission spectra of JEM:Ce3+. Fig. 4. Excitation and emission spectra of Ca-a-sialon:Ce3+. Fig. 1. Crystal structure of JEM viewed along the [0 0 1] direction. The blue, pale blue, red, and green spheres represented are La, Al, Si/Al, and O/N atoms, respectively. Fig. 3. Crystal structure of Ca-a-sialon viewed along the [0 0 1] direction. The blue, red, and green spheres represent Ca, Si/Al, and O/N atoms, respectively. 4 R.-J. Xie, N. Hirosaki / Science and Technology of Advanced Materials ] (]]]]) ]]]–]]] Please cite this article as: R.-J. Xie, N. Hirosaki, Sci. Technol. Adv. Mater. (2007), doi:10.1016/j.stam.2007.08.005

325–400 nm. They demonstrated that the N/O ratio and the crystal structure had a strong effect on the emission, Stokes shift, and crystal-field splitting. Larger N/O ratios and stiffer structures led to longer-wavelength emissions, smaller Stokes shifts, and larger crystal-field splitting [17]. A similar tendency was observed in Ce3+-doped La– Si–O–N materials [31]. We have studied the emission of Ce3+ in La–Si–O–N compounds with different structures: La5Si3O12N (hexagonal), LaSiO2N (hexagonal), and La3Si8O4N11 (orthorhombic), and have shown that La3Si8O4N11 has encouraging luminescent properties for white LEDs. Fig. 5 shows the structure of La3Si8O4N11, which contains ribbons as structural units with a composition of Si6(O,N)14. The ribbons extend along the [0 1 0] direction and are formed by corner-sharing Si(O,N)4 tetrahedra. The La1 atom is octahedrally coordinated by 4 O/N and 2 O atoms, and the La2 atom is coordinated by 5 O/N, 2 O atoms, and 1 N atom, which approximately form a cubic antiprism [50]. Fig. 6 shows the excitation and emission spectra of Ce3+-doped La–Si–O–N materials. It reveals that the peak excitation band of La–Si–O–N:Ce3+ is around 360 nm, and those of La4.9Ce0.1Si3O12N, La0.96 Ce0.04SiO2N, and La2.82Ce0.18Si8O4N11 are 472, 416, and 425 nm, respectively. We have also investigated the temperature dependence of the luminescence of Ce3+-doped La–Si–O–N materials and observed that La3Si8O4N11:Ce has the lowest thermal quenching because it has the densest structure and highest N/O ratio [31]. 3.2. Green-emitting phosphors A green-emitting phosphor is used in the case when white LEDs utilize a UV-, NUV-, or blue LED as the primary lighting source. Rare-earth-doped oxynitride and nitride green phosphors highly suitable for use in white LEDs have been reported in the literature [25,32–36], and they are reviewed below. Hirosaki et al. [32] reported a green oxynitride phosphor based on Eu2+-doped b-sialon. b-Sialon is structurally derived from b-Si3N4 by the equivalent substitution of ARTICLE IN PRESS Fig. 5. Crystal structure of La3Si8O4N11 viewed along the [0 0 1] direction. The blue, green, pale blue, red, and gray spheres represent La, N, O, Si, and O/N atoms, respectively. Fig. 6. Excitation (a) and emission (b) spectra of La4.9Ce0.1Si3O12N, La0.96Ce0.04SiO2N, and La2.82Ce0.18Si8O4N11. R.-J. Xie, N. Hirosaki / Science and Technology of Advanced Materials ] (]]]]) ]]]–]]] 5 Please cite this article as: R.-J. Xie, N. Hirosaki, Sci. Technol. Adv. Mater. (2007), doi:10.1016/j.stam.2007.08.005

Al–O for Si–N, and its chemical composition can be written as Si6zAlzOzN8z (z represents the number of Al–O pairs substituting for Si–N pairs, and 0ozp4.2). b-Sialon has a hexagonal crystal structure and the P63 or P63/m space group [51,52]. In this structure there are continuous channels parallel to the c direction (see Fig. 7). The b-sialon:Eu2+ phosphor produces intense green emission with a peak located at 538 nm, as can be seen in Fig. 8. The broad emission spectrum has a full-width at half-maximum of 55 nm. Two well-resolved broad bands centered at 303 and 400 nm are observed in the excitation spectrum. The broad excitation range enables the b-sialon:Eu2+ phosphor to emit strongly under NUV (400–420 nm) or blue (420–470 nm) light excitation. Xie et al. [33] investigated the effects of the z-value and the Eu2+ concentration on the phase formation and luminescent properties of b-sialon:Eu2+ phosphors. The results showed that (i) the samples with lower z-values (zo1.0) had higher phase purity, a smaller and more uniform particle size, and produced greater emission; (ii) the optimal Eu2+ concentration was about 0.3 mol%. In addition, the b-sialon:Eu2+ phosphor showed low thermal quenching; its emission intensity at 150 1C was 86% of that measured at room temperature [33]. Xie et al. [34] reported the green emission of Yb2+ in Caa-sialon. As can be seen in Fig. 9, the excitation spectrum shows a broad band centered at 445 nm, and the peak emission wavelength is about 550 nm upon blue-light excitation. The emission of Yb2+, arising from the transition 4f135d-4f14, usually occurs between 360 and 450 nm, as has been shown for halides, fluorides, sulphates, and phosphates [53–55]. However, luminescence occurs at low energies in Ca-a-sialon, which can principally be ascribed to the large crystal-field splitting and the strong nephelauxetic effect induced as a result of the nitrogen-rich coordination of Yb2+ in a-sialon. A much longer wavelength emission of Yb2+ in SrSi2O2N2 was observed at 620 nm by Bachmann et al. [56]. MSi2O2N2 compounds crystallize in a monoclinic lattice with different space groups and lattice parameters for M ¼ Ca, Sr, and Ba: CaSi2O2N2 (P21/c), SrSi2O2N2 (P21/m), and BaSi2O2N2 (P2/m) [25,35]. CaSi2O2N2 and SrSi2O2N2 are structurally related, both representing a new class of layered materials with layers of (Si2O2N2) 2 that consist of SiON3 tetrahedrons. The N atom bridges three Si atoms, while the O atom is bound terminally to the Si atom. There are four types of site for the M2+ ions, each surrounded by six oxygen atoms in the form of a distorted trigonal prism. The excitation and emission spectra of Eu2+-doped MSi2O2N2 materials are given in Fig. 10. As can be seen, CaSi2O2N2:Eu2+ shows a yellowish emission with a maximum intensity at 562 nm, SrSi2O2N:Eu2+ emits a green color with a maximum intensity at 543 nm, and BaSi2O2N2:Eu2+ yields blue–green emission with a peak at 491 nm. These results were also observed by Li et al. [35]. The excitation spectrum of CaSi2O2N2:Eu2+ shows a flat and broad band extending from 300 to 450 nm, while there are two well-resolved broad bands centered at 300 and ARTICLE IN PRESS Fig. 8. Excitation and emission spectra of b-sialon:Eu2+ with the composition of Si5.5Al0.5O0.5N7.5:Eu0.03. Fig. 9. Excitation and emission spectra of a-sialon:Yb2+ with the composition of Ca0.995Yb0.005Si9Al3ON15. Fig. 7. Crystal structure of b-sialon viewed along the [0 0 1] direction. The red and green spheres represent Si/Al and O/N atoms, respectively. 6 R.-J. Xie, N. Hirosaki / Science and Technology of Advanced Materials ] (]]]]) ]]]–]]] Please cite this article as: R.-J. Xie, N. Hirosaki, Sci. Technol. Adv. Mater. (2007), doi:10.1016/j.stam.2007.08.005

450 nm in the excitation spectra of SrSi2O2N2:Eu2+ and BaSi2O2N2:Eu2+, respectively. MYSi4N7 (M ¼ Sr, Ba) are quaternary nitride compounds. The structure of MYSi4N7 consists of SiN4 tetrahedra that share corners forming a three-dimensional network structure with large channels along the [1 0 0] and [0 1 0] directions formed by Si6N6 rings [36,57], as shown in Fig. 11. Both Sr2+ and Y3+ ions occupy a site in these channels. The Sr2+ ion is coordinated by 12 nitrogen atoms (SrN12) and the Y3+ ion is coordinated by six nitrogen atoms (YN6). Li et al. [36] investigated the luminescent properties of Eu2+-doped MYSi4N7 (M ¼ Sr, Ba) materials, and observed green emission when they were excited by NUV light (lex ¼ 390 nm). The emission of MYSi4N7:Eu2+ occurred at 503–527 nm for M ¼ Ba and at 548–570 nm for M ¼ Sr. The relatively short wavelength emission of Eu2+ in this nitride is ascribed to the longer bond length of Eu–N (3.011 A˚ ) than that of a-sialon ( 2.605 A˚ ) [49]. 3.3. Yellow-emitting phosphors The first commercially available white LED was fabricated in 1996 by using a yellow-emitting (Y1aGda)3 (Al1bGab)5O12 phosphor and a GaN-based blue-LED chip. The principle of this white LED is that part of the blue light from the LED chip is converted to yellow light by YAG:Ce3+, and the resulting mix of blue and yellow light has the appearance of white light. This white LED cannot create warm white light because the YAG phosphor cannot produce red emission. Moreover, the thermal quenching of the YAG phosphor is high and strongly related to its composition, leading to changes in the chromaticity of the white LED when it is used. Therefore, it is essential to develop novel yellow phosphors that emit an orangishyellow color and undergo low thermal quenching. Xie et al. [19,30,37,39,40] systematically studied the luminescent properties of Eu2+-doped Ca-a-sialon phosphors, and observed a bright yellow-orange color when they were excited by blue light. Fig. 12 shows the typical excitation and emission spectra of Eu2+-doped Ca-a-sialon. This phosphor has a broadband emission spectrum extending from 500 to 750 nm, with a peak located at 581 nm. The excitation spectrum shows two broad bands centered at 300 and 420 nm and a shoulder at 450 nm. The fact that the emission wavelength is longer than that of YAG:Ce (550–570 nm) implies that warm white light can be produced by combining Ca-asialon:Eu2+ and a blue-LED chip. In addition, the yellow emission of Ca-a-sialon:Eu2+ can be tuned by substituting Ca with other metals such as Li, Mg, and Y, and can even be adjusted by tailoring the composition of the host lattice by changing the values of m and n in the chemical formula [39,40,58,59]. Of particular interest is Li-a-sialon:Eu2+, ARTICLE IN PRESS Fig. 10. Excitation (a) and emission (b) spectra of M0.94Eu0.06Si2O2N2 (M ¼ Ca, Sr, Ba). Fig. 11. Crystal structure of SrYSi4N7 viewed along the [1 0 0] direction. The blue, pale blue, red, and green spheres represent Sr, Y, Si, and N atoms, respectively. R.-J. Xie, N. Hirosaki / Science and Technology of Advanced Materials ] (]]]]) ]]]–]]] 7 Please cite this article as: R.-J. Xie, N. Hirosaki, Sci. Technol. Adv. Mater. (2007), doi:10.1016/j.stam.2007.08.005

which emits a yellow–green color, making it possible to generate daylight light when combined with a blue LED. This indicates that warm-white-to-daylight light can be realized using a single a-sialon:Eu2+ yellow phosphor with different emission colors. Furthermore, we have demonstrated that the a-sialon:Eu2+ phosphor has lower thermal quenching than YAG:Ce3+, as shown in Fig. 13. The low thermal quenching is expected to lead to a small variation of chromaticity in white LEDs using a-sialon:Eu2+. 3.4. Red-emitting phosphors A red-emitting phosphor is usually combined with green and/or blue phosphors in the case of white LEDs utilizing a UV-, NUV-, or blue-LED chip. The search for red phosphors for use in white LEDs has been mostly concentrated on Eu3+-doped materials (e.g., NaEu(W, Mo)2O8 [60]), and Eu2+-doped sulfides (e.g., CaS:Eu2+ [5]). However, these phosphors have either low absorption in the blue-light range (i.e., oxides) or low chemical stability (i.e., sulfides). It is therefore necessary to develop red phosphors with high chemical stability and high emission efficiency upon bluelight excitations. Previous studies demonstrated that silicon-based nitride compounds are good host lattices for red luminescent materials [16,41–43], and they are described in the following. Schnick et al. [26,27] reported the crystal structures of single crystals of M2Si5N8 (M=Ca, Sr, Ba). Ca2Si5N8 has a monoclinic crystal system with the space group of Cc, whereas both Sr2Si5N8 and Ba2Si5N8 have an orthorhombic lattice with the space group of Pmn21. The local coordination in the structures is similar for these ternary alkaline-earth Si3N4’s; half the nitrogen atoms are connected to two Si neighbors and the other half have three Si neighbors. Each Ca atom in Ca2Si5N8 is coordinated to seven nitrogen atoms, while Sr in Sr2Si5N8 and Ba in Ba2Si5N8 are coordinated to eight or nine nitrogen atoms (see Fig. 14). The average bond length between alkalineearth metals and nitrogen is about 2.880 A˚ . The luminescence of Eu2+-doped Ba2Si5N8 was reported by Hoppe et al. [16], and that of Eu2+-doped M2Si5N8 (M ¼ Ca, Sr, Ba) was later reported by Li et al. [41]. The red emission in M2Si5N8:Eu2+ was attributed to the large crystal-field splitting and strong nephelauxetic effect. The red phosphor emits an intense orange-red or red color, depending on the alkaline-earth metal. The peak emission wavelength shifts upward with increasing ionic size of the alkaline-earth ARTICLE IN PRESS Fig. 13. Temperature dependence of emission intensities of Ca-a-sialon:Eu2+ and YAG:Ce3+. Fig. 14. Crystal structure of Sr2Si5N8 viewed along the [0 0 1] direction. The blue, red, and green spheres represent Sr, Si, and N atoms, respectively. Fig. 12. Excitation and emission spectra of Ca0.925Eu0.075Si9Al3ON15. The excitation and monitoring wavelengths are 420 and 581 nm, respectively. 8 R.-J. Xie, N. Hirosaki / Science and Technology of Advanced Materials ] (]]]]) ]]]–]]] Please cite this article as: R.-J. Xie, N. Hirosaki, Sci. Technol. Adv. Mater. (2007), doi:10.1016/j.stam.2007.08.005

metal, and it is 623, 640, and 650 nm for Ca2Si5N8:Eu2+, Sr2Si5N8:Eu2+, and Ba2Si5N8:Eu2+, respectively [14,41]. The excitation and emission spectra of these phosphors resemble each other. Fig. 15 shows typical luminescence spectra of Sr2Si5N8:Eu2+. The broad excitation spectrum centered at 450 nm markedly shifts to the long-wavelength side and covers the visible-light range. The temperature dependence of the emission intensity of Sr2Si5N8:Eu2+ is given in Fig. 16. The PL intensity measured at 150 1C is 86% of that measured at room temperature, indicative of low thermal quenching [61]. Uheda et al. [42] reported an alternative red phosphor with formula CaAlSiN3:Eu2+. CaAlSiN3 has an orthorhombic crystal structure and the space group of Cmc21 with unit cell parameters a ¼ 9.8007 A˚ , b ¼ 5.6497 A˚ , and c ¼ 5.0627 A˚ . The structure of CaAlSiN3 is built up of (Si/Al)N4 tetrahedra linked in a three-dimensional structure: one-third of the nitrogen atoms (N2) are linked with two Si/Al neighbors and the remaining two-thirds (N1) are connected with three Si/Al neighbors (see Fig. 17). The Al and Si atoms are randomly distributed on the same tetrahedral sites and are connected with N atoms to form vertex-linked M6N18 rings (M ¼ Al, Si). The Ca atom, residing in the tunnels surrounded by six corner-sharing tetrahedra of (Si/Al)N4, is coordinated to two four nitrogen atoms with an average distance of 2.451 A˚ . CaAlSiN3:Eu2+ is a red phosphor, and its luminescence spectra are given in Fig. 18. Both the excitation and emission spectra of CaAlSiN3:Eu2+ are very similar to those of M2Si5N8:Eu2+. The excitation spectrum is extremely broad and covers the range of 250–600 nm, closely matching the emission wavelength of NUV or blue LEDs. A broad emission band centered at 650 nm is observed upon 450 nm excitation, and it can be tuned by substituting Ca with other metals or by controlling the Eu2+ concentration [42]. The emission intensity of ARTICLE IN PRESS Fig. 16. Temperature dependence of emission intensities of Sr1.96Eu0.04 Si5N8 and Ca0.90Eu0.10AlSiN3. Fig. 18. Excitation and emission spectra of Ca0.90Eu0.10AlSiN3. The excitation and monitoring wavelengths are 450 and 650 nm, respectively. Fig. 15. Excitation and emission spectra of Sr1.96Eu0.04Si5N8. The excitation and monitoring wavelengths are 450 and 640 nm, respectively. Fig. 17. Crystal structure of CaAlSiN3 viewed along the [0 0 1] direction. The blue, red, and green spheres represent Ca/Al, Si, and N, respectively. R.-J. Xie, N. Hirosaki / Science and Technology of Advanced Materials ] (]]]]) ]]]–]]] 9 Please cite this article as: R.-J. Xie, N. Hirosaki, Sci. Technol. Adv. Mater. (2007), doi:10.1016/j.stam.2007.08.005

ARTICLE IN PRESS fore frequently utilized during their preparation.In this c route to nitride pho osphors.such as is therefor 品8p approaches have been used to synthesize oxynitride and t ).a (CRN) 4.1.Solid-state reaction The solid-staescommon simple method hor pow constituents.SisN4 powder is a commonly used starting ynth sis of mu tinary cal on-base of SiN the synthesis of nitride phost phors is usually 1500-2000C).Th CaAlSiN:Eu2+at 150C is about 89%of that measured carried out at high temperatures(i.e Si(NH)2)was used 1d0 at r Le Toquin et al.[43]reported another nitride host lattice byials may for red phosphors with include metals (e.g..Ca.Sr.Ba.Eu).metal nitrides (e.g. 162 and Gal AIN. CasN2.EuN),or metal oxides (e.g.,Al2O3,CaCO CaSiNz which is isostructural with KGaoz.crystallizes 3.Ln2O3). the samet 0 1 10MR in an orthorhombic structure with the space fepoderionoidationor'decomposSton We have applied the solid-state reaction to prepre surrounded by four N atoms with distances of 240-2.49A oxynitr d pho and by two further N atoms to form an approximately nressure sintering furnace with edral geometry. dral e Ca- sen 2 43 and 248A)and two long under a approximately 2.8A.All the nitrogen atoms in CaSiNs are at the sharec are SigNa AIN +CagN2 EuN CaAlSiN3 Eu. were observed by Le Toquin et al.[43].The maximum emission was 625nm through the following reaction between metal Ba and 40 anc silicon diimide at 1500-1650C under a nitrogen atmo- sphere Ca with Mg or Sr or that of Si with Al.The external 2Ba(Eu+5SiNH2→Ba2 SisNs:Eu2++N2+5H2 was reported to be 4.2.Gas-reduction nitridation 4.Synthesis of silicon-based oxynitride and nitride The phosphor powders prepared by the solid-state phosphors Phosphors for white lEDs epartic dis and this n ss damages the surface of particles and hence reduces the luminescence.In addition. methods. For nitride phosphors, whic some precursors such as metals or nitrides are sensitive to rogen- ing sources,a an Please cite this articles:RJ.Xie,N.Hirosaki,Sci.Technol.Adv.Mater.(do:.0

CaAlSiN3:Eu2+ at 150 1C is about 89% of that measured at room temperature (see Fig. 16). Le Toquin et al. [43] reported another nitride host lattice for red phosphors with formula CaSiN2. Crystals of CaSiN2 were prepared and the structure was determined by Ottinger et al. [62] and Gal et al. [63] independently. CaSiN2, which is isostructural with KGaO2, crystallizes in an orthorhombic structure with the space group Pnma and cell parameters a ¼ 5.1229 A˚ , b ¼ 10.2074 A˚ , and c ¼ 14.8233 A˚ . There are two sites for Ca atoms. Ca1 is surrounded by four N atoms with distances of 2.40–2.49 A˚ and by two further N atoms to form an approximately octahedral geometry. Ca2 is in a highly distorted octahedral environment, again with four shorter Ca–N distances (between 2.43 and 2.48 A˚ ) and two longer distances of approximately 2.8 A˚ . All the nitrogen atoms in CaSiN2 are at the shared vertexes of a pair of structures and are coordinated to two Si atoms (see Fig. 19). By doping CaSiN2 with Eu2+ or Ce3+, broad red emission bands were observed by Le Toquin et al. [43]. The maximum emission was at 605 and 625 nm, and the maximum excitation was at 400 and 535 nm for CaSiN2:Eu2+ and CaSiN2:Ce3+, respectively. The excitation and emission of CaSiN2:Ce3+ can be adjusted by the partial substitution of Ca with Mg or Sr or that of Si with Al. The external quantum efficiency of CaSiN2:Ce3+ was reported to be 40% [43]. 4. Synthesis of silicon-based oxynitride and nitride phosphors Phosphors for white LEDs are usually in powder form. The phosphor powders are commonly synthesized by solidstate-reaction, gas-phase, or solution (i.e., wet chemistry) methods. For nitride phosphors, which differ from oxide-based ones in that they contain nitrogen, nitride starting powders or nitrogen-containing sources, are therefore frequently utilized during their preparation. In this sense, the synthetic route to nitride phosphors, such as silicon-based multinary oxynitride and nitride phosphors, is therefore very limited. Up to now, three major approaches have been used to synthesize oxynitride and nitride phosphors: a solid-state reaction, gas-reduction nitridation (GRN), and carbothermal reduction nitridation (CRN). 4.1. Solid-state reaction The solid-state reaction is a common and simple method of synthesizing oxynitride and nitride phosphor powders. It usually involves reactions at high temperatures among powder precursors containing the corresponding chemical constituents. Si3N4 powder is a commonly used starting material for the synthesis of multinary silicon-based oxynitrides and nitrides. Because of the chemical inertness of Si3N4, the synthesis of nitride phosphors is usually carried out at high temperatures (i.e., 1500–2000 1C). The more reactive silicon diimide (Si(NH)2) was used instead of Si3N4 to synthesize nitridosilicate phosphors by Schnick and coworkers [16,26,27]. Other starting materials may include metals (e.g., Ca, Sr, Ba, Eu), metal nitrides (e.g., AlN, Ca3N2, EuN), or metal oxides (e.g., Al2O3, CaCO3, Li2CO3, Ln2O3). At the same time, a nitrogen atmosphere under pressures in the range of 0.1–1.0 MPa is required to protect the powder from oxidation or decomposition. We have applied the solid-state reaction to prepare oxynitride and nitride phosphors including a-sialon:Eu2+, b-sialon:Eu2+, JEM:Ce3+, La–Si–O–N:Ce3+, Sr2Si5N8:Eu2+, and CaAlSiN3:Eu2+. A gas-pressure sintering furnace with a graphite heating element was used. For example, CaAlSiN3:Eu2+ was formed by the following reaction among metal nitride starting powders at 1600 1C under a 1.0 MPa N2 atmosphere: Si3N4 þ AlN þ Ca3N2 þ EuN ! CaAlSiN3 : Eu: In addition, Hoppe et al. [16] used a high-frequency furnace to synthesize Ba2Si5N8:Eu2+ red phosphors through the following reaction between metal Ba and silicon diimide at 1500–1650 1C under a nitrogen atmosphere: 2Ba ðEuÞ þ 5SiðNHÞ2 ! Ba2Si5N8 : Eu2þ þ N2 þ 5H2: 4.2. Gas-reduction nitridation The phosphor powders prepared by the solid-state reaction usually consist of hard agglomerates and have a large particle size and broad size distribution. It is essential to pulverize the fired products to obtain fine and welldispersed powders, and this process damages the surface of particles and hence reduces the luminescence. In addition, some precursors such as metals or nitrides are sensitive to air and expensive, resulting in complex and multistep processing. Therefore, it is necessary to develop an ARTICLE IN PRESS Fig. 19. Crystal structure of CaSiN2 viewed along the [1 0 0] direction. The blue, red, and green spheres represent Ca, Si, and N atoms, respectively. 10 R.-J. Xie, N. Hirosaki / Science and Technology of Advanced Materials ] (]]]]) ]]]–]]] Please cite this article as: R.-J. Xie, N. Hirosaki, Sci. Technol. Adv. Mater. (2007), doi:10.1016/j.stam.2007.08.005