$1 采样过程 $2 采样周期的选取 $3 信号保持 $4 Z变换 $5 差分方程及其Z变换法求解 $6 脉冲传递函数 $7 稳定性分析 $8 采样系统动态特性的分析 $9 线性离散系统的数字校正

4—1 根轨迹法的基本概念 4—2 根轨迹绘制的基本法则 4—3 广义根轨迹 4—4 系统性能的分析

5.1 频率特性及其表示法 5.2 典型环节对数频率特性曲线的绘制 5.3 典型环节的幅相曲线的绘制 5.4 稳定裕度和判据 5.3 极坐标图(Polar plot)，幅相频率特性曲线，奈奎斯特曲线 5.3.1 积分与微分因子 5.3.2 一阶因子 5.3.3 二阶因子 5.3.4 传递延迟

System compensation is the process of designing a controller that will produce an acceptable transient response while maintaining a desired steady-state accuracy .These two design objectives are conflicting in most systems ,since small errors imply high gains reduce system stability and may even drive the system unstable .Compensation may be thought of as the process of increasing the stability of a system without reducing its accuracy below minimum acceptable standards

Frequency response is the analysis of the response of systemswhen subjected to a sinusoidal change in input. When a linear system is subjected to a sinusoidal input, its ultimate response is also a sustained sinusoidal wave, with the same frequency. The figure below compares the output response of a system (solid line) with a sinusoidal input (dashed line) disturbing the system

1 Introduction 2 Deterministic Dynamic Programming and Viscosity Solutions 2.1 Introduction 2.2 Value Functions are Viscosity Solutions 2.3 Comparison and Uniqueness 3 Stochastic Control 3.1 Some Probability Theory 3.2 Controlled State Space Models 3.3 Filtering 3.4 Dynamic Programming - Case I : Complete State Information 3.5 Dynamic Programming - Case II : Partial State Information 3.6 Two Continuous Time Problems 4 Robust Control 4.1 Introduction and Background 4.2 The Standard Problem of H∞ Control 4.3 The Solution for Linear Systems 4.4 Risk-Sensitive Stochastic Control and Robustness 5 Optimal Feedback Control of Quantum Systems 5.1 Preliminaries 5.2 The Feedback Control Problem 5.3 Conditional Dynamics 5.4 Optimal Control 5.5 Appendix: Formulas for the Two-State System with Feedback Example 6 Optimal Risk-Sensitive Feedback Control of Quantum Systems 6.1 System Model

一、工业以太网简介 二、以太网的物理连接与帧结构 三、TCP/IP协议组 四、几种典型的工业以太网

3.1 Introduction 3.2 Typical test signals for time response of control systems 3.3 First –Order Systems 3.4 Performance of a Second-Order System 3.5 Concept of Stability 3.6 The Relative Stability of Feedback Control Systems

一、对自动控制系统基本的性能要求是什么?其中最基本的要求是什么?(5分) 二、已知系统结构图如图1所示。(20分)

1. 通过实验，进一步理解线性系统的稳定性仅取决于系统本身的结构和参数，它与外作用及初始条件均无关的特性； 2. 研究系统的开环增益 K 或其它参数的变化对闭环系统稳定性的影响