D-M-E Master Unit Die UD Quick-Change TM U-Style Frames Companion Insert molds -D-M-E
D-M-E Master Unit Die Quick-Change™ U-Style Frames & Companion Insert Molds
UF 2 Table of contents Model 05/05 UF 321 Companion Insert Mold (3.25 x 7.5 &4.0 x 4.7) Model 07/07 UF 321 Companion Insert Mold(4.5 x 6.25 & 6.0 x 7.25) Model 08/09 UF 321 Companion Insert Mold (5.0 x 8.0&7.85 x 9.0) UF 8 Model 08/10 UF 321 Companion Insert Mold (5.0 x 9.0& 7.85 x 9.0) UF 9 Enhanced Series Mold Inserts-Solid UF 10 Enhanced series mold Inserts -Laminated Model 94/90 UF 321 Companion Insert Mold (6.5 x 8.0&8. x 9.0) UF 12 Model 84/90 UF 321 Companion Insert Mold (6.5 x 8.0&8.4 x 9.0) Model 09/07 UF 321 Companion Insert Mold (6.0 x 6.75&9.0 x 6.75 UF 14 Model09/07EB321c0 mpanion Insert Mold60x6,75&9.0X6.75)………UF15 Model 10/12 UF 321 Companion Insert Mold (7.0 x 10.9&9.9 x 10.9) Model 10/14 UF 321 Companion Insert Mold (7.0 x 12.9&9.9 x 12.9) UF 17 Model 10/16 UF 321 Companion Insert Mold (7.0 x 14.9&9.9 x 14.9 UF 18 Model 11/11 UF 321 Companion Insert Mold (8.0 x 10.0&11.5 x 11.0) UF 19 Model 12/08 UF 321 Companion Insert Mold (8.0 x 8.0&11.9 x8.0) UF 20 Model 12/14 UF 321 Companion Insert Mold (8.0 x 12.9 & 11.9 x 12.9) Model 12/16 UF 321 Companion Insert Mold (8.0 x 14.9&11.9 x 14.9) UF 22 Model 12/18 UF 321 Companion Insert Mold(8.0 x 16.9& 11.9 x 16.9) UF 23 Model 12/20 UF 321 Companion Insert Mold (8.0 x 18. 9& 11.9 x 18.9) UF 24 Model 13/16 UF 321 Companion Insert Mold (9.0 x 14.9& 12.9 x 14.9 UF 25 Model 13/18 UF 321 Companion Insert Mold (9. x 16.9 & 12. 9 x 16.9 Model 13/20 UF 321 Companion Insert Mold(9.0 x 18.9&12.9 x 18.9) UF 27 Model 13/22 UF 321 Companion Insert Mold(9.0 x 20.9& 12.9 x 18.9) UF 28 Model 14/16 UF 321 Companion Insert Mold (10.0 x 14.9& 13.9 x 14.9)..... UF 29 Model 14/18 UF 321 Companion Insert Mold (10.0 x 16.9& 13.9 x 16 Model 14/20 UF 321 Companion Insert Mold (10.0 x 18.9& 13.9 x 18.9)..... UF 31 Model 14/22 UF 321 Companion Insert Mold (10.0 x 20. 9& 13.9 x 20.9)...... UF 32 Model 16/18 UF 321 Companion Insert Mold (11.0 x 15.9& 15.9 x 15.9)..... UF 33 Model 16/21 UF 321 Companion Insert Mold (11.0 x 18. 9& 15.9 x 18.9)...... UF 34 Model 16/27 UF 321 Companion Insert Mold (11.0 x 24.9& 15.9 x 24.9)..... UF 36 Model 18/20 UF 321 Companion Insert Mold(12.0 x 17.9&17.9 x 17.9)..... UF 37 Model 18/26 UF 321 Companion Insert Mold (12.0 x 23 9& 17.9 x 23.9)..... UF 38 Insert Mold pillar Posts MASTER 626-6653 UNIT DE Canada 800-387-6600 wdme. net
UF 2 Table of Contents U.S. 800-626-6653 Canada 800-387-6600 ■ www.dme.net Model 05/05 UF 321 Companion Insert Mold (3.25 x 7.5 & 4.0 x 4.7) ……… UF 6 Model 07/07 UF 321 Companion Insert Mold (4.5 x 6.25 & 6.0 x 7.25) ……… UF 7 Model 08/09 UF 321 Companion Insert Mold (5.0 x 8.0 & 7.85 x 9.0) ……… UF 8 Model 08/10 UF 321 Companion Insert Mold (5.0 x 9.0 & 7.85 x 9.0)………… UF 9 Enhanced Series Mold Inserts – Solid ………………………………… UF 10 Enhanced Series Mold Inserts – Laminated …………………………… UF 11 Model 94/90 UF 321 Companion Insert Mold (6.5 x 8.0 & 8.4 x 9.0) ……… UF 12 Model 84/90 UF 321 Companion Insert Mold (6.5 x 8.0 & 8.4 x 9.0) ……… UF 13 Model 09/07 UF 321 Companion Insert Mold (6.0 x 6.75 & 9.0 x 6.75)……… UF 14 Model 09/07 EB 321 Companion Insert Mold (6.0 x 6.75 & 9.0 x 6.75) ……… UF 15 Model 10/12 UF 321 Companion Insert Mold (7.0 x 10.9 & 9.9 x 10.9) ……… UF 16 Model 10/14 UF 321 Companion Insert Mold (7.0 x 12.9 & 9.9 x 12.9) ……… UF 17 Model 10/16 UF 321 Companion Insert Mold (7.0 x 14.9 & 9.9 x 14.9) ……… UF 18 Model 11/11 UF 321 Companion Insert Mold (8.0 x 10.0 & 11.5 x 11.0) …… UF 19 Model 12/08 UF 321 Companion Insert Mold (8.0 x 8.0 & 11.9 x 8.0) ……… UF 20 Model 12/14 UF 321 Companion Insert Mold (8.0 x 12.9 & 11.9 x 12.9) …… UF 21 Model 12/16 UF 321 Companion Insert Mold (8.0 x 14.9 & 11.9 x 14.9) …… UF 22 Model 12/18 UF 321 Companion Insert Mold (8.0 x 16.9 & 11.9 x 16.9) …… UF 23 Model 12/20 UF 321 Companion Insert Mold (8.0 x 18.9 & 11.9 x 18.9) …… UF 24 Model 13/16 UF 321 Companion Insert Mold (9.0 x 14.9 & 12.9 x 14.9) …… UF 25 Model 13/18 UF 321 Companion Insert Mold (9.0 x 16.9 & 12.9 x 16.9) …… UF 26 Model 13/20 UF 321 Companion Insert Mold (9.0 x 18.9 & 12.9 x 18.9) …… UF 27 Model 13/22 UF 321 Companion Insert Mold (9.0 x 20.9 & 12.9 x 18.9) …… UF 28 Model 14/16 UF 321 Companion Insert Mold (10.0 x 14.9 & 13.9 x 14.9) …… UF 29 Model 14/18 UF 321 Companion Insert Mold (10.0 x 16.9 & 13.9 x 16.9) …… UF 30 Model 14/20 UF 321 Companion Insert Mold (10.0 x 18.9 & 13.9 x 18.9) …… UF 31 Model 14/22 UF 321 Companion Insert Mold (10.0 x 20.9 & 13.9 x 20.9) …… UF 32 Model 16/18 UF 321 Companion Insert Mold (11.0 x 15.9 & 15.9 x 15.9) …… UF 33 Model 16/21 UF 321 Companion Insert Mold (11.0 x 18.9 & 15.9 x 18.9) …… UF 34 Model 16/24 UF 321 Companion Insert Mold (11.0 x 21.9 & 15.9 x 21.9) …… UF 35 Model 16/27 UF 321 Companion Insert Mold (11.0 x 24.9 & 15.9 x 24.9) …… UF 36 Model 18/20 UF 321 Companion Insert Mold (12.0 x 17.9 & 17.9 x 17.9) …… UF 37 Model 18/26 UF 321 Companion Insert Mold (12.0 x 23.9 & 17.9 x 23.9) …… UF 38 Insert Mold Pillar Posts …………………………………………………… UF 39
UF 3 Frame Ordering Information Item number and description (see charts on corresponding page) S" diameter of locating ring supplied standard (see drawings on corresponding page Sprue bushing(if required)"R"spherical radius of sprue bushing furnished 1/2"or 3 /4"unless otherwise shown 0"small diameter of sprue bushing orifice furnished 5/32, 7/32, 9/32"or 11/32" unless otherwise shown Optional locating rings and sprue bushings available on request TANDARD SOLID Knockout hole locations standard as shown (other optional INSERT MOLD Clamp slots standard unless otherwise shown on corresponding page Mounting holes optional unless shown on corresponding page Additional height of ejection available (quotation on request) Frames standard in prehard #2 steel. Prehard stainless and other steel grades available(quotation on request) Other frame options are available on request Insert Mold Ordering Information STANDARD LAMINATED Item number and description(see charts on corresponding page) INSERT MOLD Steel grades-1020, 4130 prehard, P-20 prehard and H-13: 420 stainless and other grades on request T-style laminated insert molds supplied with 4130 prehard ear plates except in tool steel insert molds have tool steel ear plates H-13 and other tool steel insert molds supplied 010 oversize on outside dimension. .010-.013 oversize on thickness and 025-.035 undersize in pin and bushing holes for machining after required heat treating A"and"B" dimensions supplied .004-.007 oversize unless otherwise specified Other"A"and"B"thicknesses available on request T-STYLE LAMINATED U.S.8oo626-6653 Canada00-387-6600www.dme.net
U.S. 800-626-6653 Canada 800-387-6600 ■ www.dme.net UF 3 Frame Ordering Information • Item number and description (see charts on corresponding page) • “S” diameter of locating ring supplied standard (see drawings on corresponding page) • Sprue bushing (if required) “R” spherical radius of sprue bushing furnished 1/2” or 3/4” unless otherwise shown • “O” small diameter of sprue bushing orifice furnished 5/32”, 7/32”, 9/32” or 11/32” unless otherwise shown • Optional locating rings and sprue bushings available on request • Knockout hole locations standard as shown (other optional) • Clamp slots standard unless otherwise shown on corresponding page • Mounting holes optional unless shown on corresponding page • Additional height of ejection available (quotation on request) • Frames standard in prehard #2 steel. Prehard stainless and other steel grades available (quotation on request) • Other frame options are available on request Insert Mold Ordering Information • Item number and description (see charts on corresponding page) • Steel grades – 1020, 4130 prehard, P-20 prehard and H-13: 420 stainless and other grades on request • T-style laminated insert molds supplied with 4130 prehard ear plates except in tool steel insert molds have tool steel ear plates • H-13 and other tool steel insert molds supplied .010 oversize on outside dimension, .010 – .013 oversize on thickness, and .025 – .035 undersize in pin and bushing holes for machining after required heat treating • “A” and “B” dimensions supplied .004 – .007 oversize unless otherwise specified • Other “A” and “B” thicknesses available on request STANDARD SOLID INSERT MOLD STANDARD LAMINATED INSERT MOLD T-STYLE LAMINATED INSERT MOLD
Quick-Change U frame features and applications This MUD Quick-Change frame and companion insert mold series com- bines the cost saving benefits and time saving advantages of the Master Unit Die Concept with exceptional design flexibility U frames accept two type of companion insert molds-the standard style(inside frame width) and T-style (outside frame width) companion insert molds. These can be ordered in any thickness in which the frame Quick-Change and insert stack height do not exceed the minimum or maximum shut U frame options height of the machine. The frame's open design permits installation of water lines or hydraulic cylinders on any side of the insert mold. Options Removable center runner bars for include insulation boards, master ejector plates and master ejector two-insert mold applications plates with interlocking rails Master ejector plates MUD Quick-Change U frames can be adapted to multiple insert mold Master ejector plates with interlocking rails applications with the addition of an optional removable center runner bar and master ejector plate. This allows simultaneous production with ● Frame spacer bars two smaller insert molds in either the T-style or standard style Other U frame series cost reduction options include frame spacer bars Hot tip sprue bushings and adapter rails. Spacer bars permit the use of shorter and lower cost e Insulation boards companion insert molds in frames designed for longer sizes. Adapte Additional height on ejector rails rails permit the use of narrower and lower cost insert molds in frames designed for wider sizes Armorclad plating* Electroless nickel plating Armorclad"is the registered trademark of STEEL SPECIFICATIONS: Standard U frames are produced in prehard steel (285-325 Brinell). Prehard stainless, 420 stainless, H-13 and other NOTE: Specifications subject to change grades are available on request. armorclad" Number One can be specified. Guide rails on larger frames are treated for enhanced wear resistance Armorclad"is the registered trademark of Armorclad, Inc. MASTER U.s.80o-626-6653 UNIT DIE Canada00-387-6600mwww.dme.net
UF 4 Quick-Change U frame features and applications U.S. 800-626-6653 Canada 800-387-6600 ■ www.dme.net This MUD Quick-Change frame and companion insert mold series combines the cost saving benefits and time saving advantages of the Master Unit Die Concept with exceptional design flexibility. U frames accept two type of companion insert molds — the standard style (inside frame width) and T-style (outside frame width) companion insert molds. These can be ordered in any thickness in which the frame and insert stack height do not exceed the minimum or maximum shut height of the machine. The frame’s open design permits installation of water lines or hydraulic cylinders on any side of the insert mold. Options include insulation boards, master ejector plates and master ejector plates with interlocking rails. MUD Quick-Change U frames can be adapted to multiple insert mold applications with the addition of an optional removable center runner bar and master ejector plate. This allows simultaneous production with two smaller insert molds in either the T-style or standard style. Other U frame series cost reduction options include frame spacer bars and adapter rails. Spacer bars permit the use of shorter and lower cost companion insert molds in frames designed for longer sizes. Adapter rails permit the use of narrower and lower cost insert molds in frames designed for wider sizes. STEEL SPECIFICATIONS: Standard U frames are produced in prehard steel (285-325 Brinell). Prehard stainless, 420 stainless, H-13 and other grades are available on request. Armorclad* Number One can be specified. Guide rails on larger frames are treated for enhanced wear resistance. * “Armorclad” is the registered trademark of Armorclad, Inc. Quick-Change U frame options • Removable center runner bars for two-insert mold applications • Master ejector plates • Master ejector plates with interlocking rails • Frame spacer bars • Adapter rails • Hot tip sprue bushings • Insulation boards • Additional height on ejector rails • Armorclad plating* • Electroless nickel plating * “Armorclad” is the registered trademark of Armorclad, Inc. NOTE: Specifications subject to change without prior notice
UF 5 Companion insert mold features and applications The two companion insert mold styles available with the Quick-Change U frame increase the exceptional design flexibility of this series. A wide range of options adds to this versatility the result is the most versatile njection molding tooling offered to the industry T-style insert molds offer the maximum projected mold area and are available in laminated construction including three -and four-plate designs Smaller sizes are available in either solid or laminated construction Companion Standard insert molds are the most economical style and are recommended insert mold options when the additional width of the T-style is not required. Standard insert molds are available in solid or laminated construction including three and T-style insert molds in laminated four plate designs insert molds in solid Both style insert molds can be ordered with a complete ejector system laminated construction including return pins and pillar posts. Other options include stripper plates, Three-plate design for pinpoint gating sleeve ejection and three-plate construction for a pinpoint gating system Machining for heater cartridge holes, water lines, rough or finished ● Stripper plates pockets, taper locks and other special applications is also available. A ● Sleeve ejection noted, the open design of the U frame permits installation of water lines Return pins and pillar posts or hydraulic cylinders on any side of the insert molds. mining for Design options for insert molds include spring loading, early return, Heater cartridge holes unscrewing mechanisms, hot tip sprue bushings, runnerless molding and machining for cam slides. Insert molds can be ordered with interlocking Machining for water lines ejector plates for positive return and stroking action when used with Rough cut pockets frames having an interlocking ejector system Finished custom pockets ● Runnerless molding Machining for special applications Steel Specifications: Companion insert molds are available in 1020 available on request. Ear plates for T-style laminated insert molds are a 4130 prehard, P-20 prehard and H-13 420 stainless and other grades ar Armorclad plating Armorclad" is the registered trademark of supplied 4130 steel with the exception of tool steel insert molds which are supplied with tool steel ear plates. Armorclad* Number One can NOTE: Specifications subject to change Armorcladis the registered trademark of Armorclad, Inc. U.S.8o626-6653 MASTER Canada00-387-6600awww.dme.net UNIT DE
U.S. 800-626-6653 Canada 800-387-6600 ■ www.dme.net UF 5 Companion insert mold features and applications The two companion insert mold styles available with the Quick-Change U frame increase the exceptional design flexibility of this series. A wide range of options adds to this versatility. The result is the most versatile injection molding tooling offered to the industry. T-style insert molds offer the maximum projected mold area and are available in laminated construction including three- and four-plate designs. Smaller sizes are available in either solid or laminated construction. Standard insert molds are the most economical style and are recommended when the additional width of the T-style is not required. Standard insert molds are available in solid or laminated construction including three and four plate designs. Both style insert molds can be ordered with a complete ejector system including return pins and pillar posts. Other options include stripper plates, sleeve ejection and three-plate construction for a pinpoint gating system. Machining for heater cartridge holes, water lines, rough or finished pockets, taper locks and other special applications is also available. As noted, the open design of the U frame permits installation of water lines or hydraulic cylinders on any side of the insert molds. Design options for insert molds include spring loading, early return, unscrewing mechanisms, hot tip sprue bushings, runnerless molding and machining for cam slides. Insert molds can be ordered with interlocking ejector plates for positive return and stroking action when used with frames having an interlocking ejector system. Steel Specifications: Companion insert molds are available in 1020, 4130 prehard, P-20 prehard and H-13. 420 stainless and other grades are available on request. Ear plates for T-style laminated insert molds are supplied 4130 steel with the exception of tool steel insert molds which are supplied with tool steel ear plates. Armorclad* Number One can be specified. * “Armorclad” is the registered trademark of Armorclad, Inc. Companion insert mold options • T-style insert molds in laminated construction • Standard insert molds in solid or laminated construction • Three-plate design for pinpoint gating • Stripper plates • Sleeve ejection • Return pins and pillar posts • Machining for taper locks • Heater cartridge holes • Machining for water lines • Rough cut pockets • Finished custom pockets • Runnerless molding • Machining for special applications • Armorclad plating* * “Armorclad” is the registered trademark of Armorclad, Inc. NOTE: Specifications subject to change without prior notice
UF 6 05/05 UF Quick-Change U-Style uF321 Frame S Companion Insert Molds Companion Interchangeable Insert Molds Frame O Frame clamps at this end of insert mold and ejector plates are flush with this end of insert. 2 Support post not supplied. Grind +001 to +.002 higher than height of ejection (see page UF 39) 3 Thicker plate optiona Standard solid Standard Laminated T-Style Laminated: 3.25X3.75 3.25x3.75 4.0x4.7 UF 321 Frame Upper-Side View 5/16 Ejector 3.750 3.750 3248:01 Offset NOTE: Sprue bushing supplied flat with. 125 small UF 321 Frame Upper-Top View A A2 388}1/420THD10 ! 眨 B IB2 Standard solid construction UF 321 Frame Lower-Side View 505s52137 1377 05/05SSU222 1877 1.877 tandard Laminated Construction A2B2 05/05SLU2811377087708771377 1001 05/05SLU2821877137713771.877 "0 degree. 15 minute taper slot to acc sleeve 3.750 length T-Style Laminated Construction UF 321 Frame Lower-Top vier 0505TLU20114501.00010001450 505TLU2021950150015001 3253 378x5°Lead Ordering information for frame and companion insert molds can be found in the front of this catalo 3.750 100 U.s.80o-626-6653 Canada00-387-6600mwww.dme.net
UF Quick-Change U-Style Frame & Companion Insert Molds 05/05 UF 321 UF 6 U.S. 800-626-6653 Canada 800-387-6600 ■ www.dme.net Frame ITEM NO. 05/05 UF 321 Standard Solid: 3.25 x 3.75 ITEM NO. A A2 B2 B 05/05 SLU 281 1.377 0.877 0.877 1.377 05/05 SLU 282 1.877 1.377 1.377 1.877 *O degree - 15 minute taper slot to accommodate sleeve ejection retainer plate. Slot tapers from .125 to .109 in 3.750 length). ITEM NO. A A2 B2 B 05/05 TLU 201 1.450 1.000 1.000 1.450 05/05 TLU 202 1.950 1.500 1.500 1.950 ITEM NO. A B 05/05 SSU 221 1.377 1.377 05/05 SSU 222 1.877 1.877 Standard Solid Construction Standard Laminated Construction T-Style Laminated Construction Companion Interchangeable Insert Molds Ordering information for frame and companion insert molds can be found in the front of this catalog. 1 Frame clamps at this end of insert mold and ejector plates are flush with this end of insert. 2 Support post not supplied. Grind +.001 to +.002 higher than height of ejection (see page UF 39). 3 Thicker plate optional. T-Style Laminated: 4.0 x 4.7 Standard Laminated: 3.25 x 3.75 UF 321 Frame Upper – Side View UF 321 Frame Upper – Top View UF 321 Frame Lower – Side View UF 321 Frame Lower – Top View "S" Ø 2.358 Ø 1.0 SB2310-63-001 .45 .45 .90 .28 UC 2520 .50 Ø .125 1.875 1.388 2.437 1.388 1/4-20 THD (10) 1.875 1.500 4.75 3.750 4.88 3.253 +.002 –.000 3/8 x 5° Lead .375 1.00 1/4-20 .190 THD Ø 1.001 2.88 .15 2.76 2.31 .45 .45 .190 .125 1.865 ±.0005 * Ejector Half .375 3.62 3.750 .500 Offset 3.248 3.598 ±.001 .375 1 .450 1.865 Ejection 2.75 Central .175 A .184 Ø .250 .450 B 2 3 .240 .240 .500 Offset 3.248 3.598 .375 .375 1 .175 A .184 Ø .250 .240 .240 2.75 Central 3.62 3.750 2 3 B 1.865 Ejection .50 A2 .50 B2 Ejector Half ±.001 2.75 Central 2 3 .240 .240 1.865 Ejection 1 Ø .250 B .45 B2 .375 2.75 4.000 1.26 .45 3.248 3.598 ±.001 .184 .175 A2 A Ø 5/16 Dowel .375 .31 3.62 3.750 4.700 .500 Offset Ejector Half NOTE: Sprue bushing supplied flat with .125 small diameter orifice standard
UF 7 07/07 UF321 Companion Interchangeable Insert Molds Frame (1 Frame clamps at this end of insert mold and ejector plates are flush with this end of insert. 2 Support post not supplied Grind +.001 to+.002 higher than height of ejection (see page UF 39) 3 Thicker plate optional Standard solid Standard Laminated T-Style Solid or 0707UF321 4.5x6.25 4.5x6.25 Laminated: 6.0 x 7.25 ① UF 321 Frame Upper-Side View 6.250 6.250 sB2025-88 250 B5/16 UC252056 6000 |}230 20一巨4F3 Frame Upper -Top Vie 1/213THD(20 P0375 =035 816THD(8} 0375L +B2 Ejection Central Standard solid Construction 3.375 UF 321 Frame Lower-Side View 0707SSU221 1/4-20THD 0707s50222137 877 07/07SsU2241877 1877 Standard Laminated Construction 0707LU281137708770871377 107SU2821377087137187 sleeve ejection retainer plate. Slot tapers from 187 to 160 in 6.250 length 07/07SLU2831877137708771377 0707SU2841.87713771377187 UF 321 Frame Lower-Top View T-Style Solid Construction 毗A配 07/07TSU2421.87512501250187 7.25 0707TLU2011.6251.00010001.625 Ordering information for frame and companion insert olds can be found in the front of this catalog U.S.8oo626-6653 MASTER Canada800-387-6600www.dme.net UNIT DE
U.S. 800-626-6653 Canada 800-387-6600 ■ www.dme.net 07/07 UF 321 UF 7 Frame ITEM NO. Standard Solid: 07/07 UF 321 4.5 x 6.25 ITEM NO. A A2 B2 B 07/07 SLU 281 1.377 0.877 0.877 1.377 07/07 SLU 282 1.377 0.877 1.377 1.877 07/07 SLU 283 1.877 1.377 0.877 1.377 07/07 SLU 284 1.877 1.377 1.377 1.877 ITEM NO. A A2 B2 B 07/07 TLU 201 1.625 1.000 1.000 1.625 07/07 TLU 202 1.875 1.250 1.250 1.875 ITEM NO. A B 07/07 SSU 221 1.377 1.377 07/07 SSU 222 1.377 1.877 07/07 SSU 223 1.877 1.377 07/07 SSU 224 1.877 1.877 Standard Solid Construction Standard Laminated Construction T-Style Laminated Construction ITEM NO. A A2 B2 B 07/07 TSU 241 1.625 1.000 1.000 1.625 07/07 TSU 242 1.875 1.250 1.250 1.875 T-Style Solid Construction Companion Interchangeable Insert Molds Ordering information for frame and companion insert molds can be found in the front of this catalog. 1 Frame clamps at this end of insert mold and ejector plates are flush with this end of insert. 2 Support post not supplied. Grind +.001 to +.002 higher than height of ejection (see page UF 39). 3 Thicker plate optional. T-Style Solid or Laminated: 6.0 x 7.25 Standard Laminated: 4.5 x 6.25 .230 A B .360 .246 Ø .375 2 3 .625 .625 .360 .437 .437 6.00 6.250 4.496 4.956 ±.001 Ejector Half .562 Offset 1 2.500 Ejection 3.87 Central 3.87 Central .230 A .246 Ø .375 .437 .437 6.00 6.250 4.496 4.956 ±.001 Ejector Half .562 Offset 1 B .360 2 3 2.500 .360 Ejection .50 A2 .50 B2 A B .360 .246 Ø .375 3 .625 .360 B2 .437 3.75 .625 4.496 4.956 ±.001 A2 .437 .31 6.000 2 2.500 Ejection 3.87 Central 1 Ø 5/16 Dowel .562 Offset 1.31 .230 6.250 7.250 6.00 Ejector Half *O degree - 15 minute taper slot to accommodate sleeve ejection retainer plate. Slot tapers from .187 to .160 in 6.250 length. UF 321 Frame Upper – Side View UF 321 Frame Upper – Top View UF 321 Frame Lower – Side View UF 321 Frame Lower – Top View LR171 SB2025-88 UC 2520 .56 Ø 3.99 ”S“ Ø 2.5 1.23 .60 .625 .28 R Ø O .187 3.625 2.625 3.375 1.50 3/8-16 THD (8) 1/2-13 THD (20) 3.375 1.949 2.366 3.750 2.756 2.366 1.949 3/8 x 5° Lead 7.25 2.625 3.625 7.50 4.500 .12 7.50 6.25 .500 1.00 +.002 -.000 1/4-20 THD 4.12 .156 .250 .625 ±.0005 2.500 3.12 3.73 .60 .50 Ø 1.126 .81 .253 .187 *
UF 8 08/09 UF Quick-Change U-Style uF321 Frame S Companion Insert Molds Companion Interchangeable Insert Molds Frame O Frame clamps at this end of insert mold and ejector plates are flush with this end of insert Support post not supplied Grind +001 to + 002 higher than height of ejection(see page UF 39) 3 Thicker plate optional 08/09UF321 Standard solid Standard Laminated T-Style Solid or 50x8.0 5.0x80 Laminated: 7.85x 9.0 UF 321 Frame Upper-Side View S3.990 B25 8.000 60 5/16 4.996 4.996 owel UF 321 Frame Upper-Top View 0375 -B375U 6 500 750 B2 一B2 THD(18 =35 Standard solid Construction T-Style Solid Construction UF 321 Frame Lower-Side View 08/09SSU221 809TSU24117501.00010001750 08/09SsU221377 187080918u242|1750100150220 08/09SSU223 .877 08/09TSU2432000125012502000 08/09SsU2241.877 0809TSU24422501.5001001.750 0809s592518772370809su2452201501502250 08/09TSu2462625187518752625 0809s272377 08/09SSU228 009ssU22877 2377 T-Style Laminated Construction "0 degree- 15 minute taper slot to accommodate sleeve ction retainer plate. Slot tapers from 285 to. 250 i 8.000 length. Standard Laminated Construction 08/09TLU2011750100010011.750 UF 321 Frame Lower-Top View ITEM 0809TLU2021750100015002250 38X5°Lead 009U281137062706271377 0809TU2032000125012502000 0809TLU20422501.50010001.750 0808sU282131021218709nu2m5220150150250 0809sLU28318711062713 080snU2062625187518752625 0809SLU28418771.1271.1271.877 6272377 Solid construction 08/09SLU28623771627 1.1271.877Aluminum Companion Insert Molds 030su287237162716272377FmEM 08/09SLU2882377162721272877 08095su2892872127162723771080AU2081875 Ordering information for frame and companion insert NoTE A&"B dimensions are supplied +. 001 on all molds can be found in the front of this catalog MASTER U.s.80o-626-6653 UNIT DE Canada00-387-6600mwww.dme.net
UF 321 Frame Lower – Top View 4.000 9.00 8.00 1.00 .500 7.85 5.000 +.002 –.000 3/8 x 5° Lead UF Quick-Change U-Style Frame & Companion Insert Molds 08/09 UF 321 UF 8 U.S. 800-626-6653 Canada 800-387-6600 ■ www.dme.net Frame ITEM NO. 08/09 UF 321 Standard Solid: 5.0 x 8.0 ITEM NO. A A2 B2 B 08/09 SLU 281 1.377 0.627 0.627 1.377 08/09 SLU 282 1.377 0.627 1.127 1.877 08/09 SLU 283 1.877 1.127 0.627 1.377 08/09 SLU 284 1.877 1.127 1.127 1.877 08/09 SLU 285 1.877 1.127 1.627 2.377 08/09 SLU 286 2.377 1.627 1.127 1.877 08/09 SLU 287 2.377 1.627 1.627 2.377 08/09 SLU 288 2.377 1.627 2.127 2.877 08/09 SLU 289 2.877 2.127 1.627 2.377 08/09 SLU 290 2.877 2.127 2.127 2.877 *O degree - 15 minute taper slot to accommodate sleeve ejection retainer plate. Slot tapers from .285 to .250 in 8.000 length. ITEM NO. A A2 B2 B 08/09 TLU 201 1.750 1.000 1.000 1.750 08/09 TLU 202 1.750 1.000 1.500 2.250 08/09 TLU 203 2.000 1.250 1.250 2.000 08/09 TLU 204 2.250 1.500 1.000 1.750 08/09 TLU 205 2.250 1.500 1.500 2.250 08/09 TLU 206 2.625 1.875 1.875 2.625 ITEM NO. A A2 B2 B 08/09 TSU 241 1.750 1.000 1.000 1.750 08/09 TSU 242 1.750 1.000 1.500 2.250 08/09 TSU 243 2.000 1.250 1.250 2.000 08/09 TSU 244 2.250 1.500 1.000 1.750 08/09 TSU 245 2.250 1.500 1.500 2.250 08/09 TSU 246 2.625 1.875 1.875 2.625 ITEM NO. A B 08/09 SSU 221 1.377 1.377 08/09 SSU 222 1.377 1.877 08/09 SSU 223 1.877 1.377 08/09 SSU 224 1.877 1.877 08/09 SSU 225 1.877 2.377 08/09 SSU 226 2.377 1.877 08/09 SSU 227 2.377 2.377 08/09 SSU 228 2.377 2.877 08/09 SSU 229 2.877 2.377 08/09 SSU 230 2.877 2.877 Standard Solid Construction Standard Laminated Construction T-Style Laminated Construction T-Style Solid Construction Companion Interchangeable Insert Molds Ordering information for frame and companion insert molds can be found in the front of this catalog. 1 Frame clamps at this end of insert mold and ejector plates are flush with this end of insert. 2 Support post not supplied. Grind +.001 to +.002 higher than height of ejection (see page UF 39). 3 Thicker plate optional. T-Style Solid or Laminated: 7.85 x 9.0 Standard Laminated: 5.0 x 8.0 .437 .437 7.88 8.000 .562 Offset Ejector Half 4.996 5.456 ±.001 .230 A B .360 .246 Ø .375 2.625 Ejection 4.00 Central 2 3 .750 1 .750 .360 .437 .437 7.88 8.000 .562 Offset Ejector Half 4.996 5.456 ±.001 .230 A B .360 .246 Ø .375 2.625 Ejection 4.00 Central 2 3 .75 1 .750 .360 A2 B2 Ejector Half A B .360 .246 Ø .500 2.625 Ejection 4.00 Central 2 3 1 .75 .360 B2 .562 4.68 7.850 .75 4.996 5.456 ±.001 A2 Ø 5/16 Dowel .562 .31 7.88 8.000 9.000 .687 Offset .230 1.31 UF 321 Frame Upper – Side View UF 321 Frame Upper – Top View UF 321 Frame Lower – Side View UC 3816 .60 1.35 .60 .75 .44 SB2025-88 LR171 Ø O Ø 2.5 R Ø S 3.990 .187 1.50 1/2 -13 THD (18) 3.375 2.366 4.000 2.756 3.925 3.375 2.366 3/8-16 .250 THD 4.12 Ø 1.126 .25 .50 .81 .60 .285 .253 .75 3.97 2.625 3.37 ±.0005 * ITEM NO. A B 08/09 ALU 208 1.875 1.875 08/09 ALU 210 2.375 1.875 Solid Construction Aluminum Companion Insert Molds NOTE: “A” & “B” dimensions are supplied ±.001 on all aluminum companion insert molds. Aluminum grade is QC-7
08/10 UF321 Companion Interchangeable Insert Molds ramme O Frame clamps at this end of insert mold and ejector plates are flush with this end of insert. @2 Support post not supplied. Grind +.001 to +002 higher than height of ejection (see page UF 39 Standard solid Standard Laminated T-Style Solid or 08/10UF321 5.0x9.0 5.0x90 Laminated: 7.85x 9.0 UF 321 Frame Upper-Side View BS3990 888 LR171 9000 Eject SB2025-88 9.000 Uc3816 Offset Offset 7.850 UF 321 Frame Upper -Top View 230 1/2-13THD(18) 4.996 =0375「 1B2 2360 Centra 2625 Ejection 360 Central Standard Solid Construction - style Solid Construction UF 321 Frame Lower-Side View 08/10SSU2211377 1377 08/0TSU2411.75010001.001750 07su242101100150120 08/10SSU223 1877 1377 0810TSU2432000125012502000 08/10SSU224 1877 1870810512412015010010 2.625 237708/10TSU245225015001.5002250 08/10SsU2262377 08/10TSU246262518751.8752625 0810ssu27237 08/10SSU2282377 2877 te taper slot to accommodate sleeve 08/10SsU230 2877 Standard Laminated Construction T-Style Laminated Construction UF 321 Frame Lower-Top View ITEM TIEM A A2B2B 5.000 3/8x 5 Lead 810SuU28113770.627062713770810nU2011750100010001750 08/10SLU282137706271127 0810U202173010041501220 00suU283187117062713770810TU20320012501250200 0810SLU284187711271.1271877 00sLU28518711716723770810U25220150015002250 08/10SLU2872377162716272377 0810SU28823771.62721272877 08/10SLU289287721271627237 0810sU29028772127|2127|287 Ordering information for frame and companion insert molds can be found in the front of this catalog U.S.8oo626-6653 MASTER Canada800-387-6600www.dme.net UNIT DE
U.S. 800-626-6653 Canada 800-387-6600 ■ www.dme.net 08/10 UF 321 UF 9 Frame ITEM NO. Standard Solid: 08/10 UF 321 5.0 x 9.0 ITEM NO. A A2 B2 B 08/10 SLU 281 1.377 0.627 0.627 1.377 08/10 SLU 282 1.377 0.627 1.127 1.877 08/10 SLU 283 1.877 1.127 0.627 1.377 08/10 SLU 284 1.877 1.127 1.127 1.877 08/10 SLU 285 1.877 1.127 1.627 2.377 08/10 SLU 286 2.377 1.627 1.127 1.877 08/10 SLU 287 2.377 1.627 1.627 2.377 08/10 SLU 288 2.377 1.627 2.127 2.877 08/10 SLU 289 2.877 2.127 1.627 2.377 08/10 SLU 290 2.877 2.127 2.127 2.877 ITEM NO. A A2 B2 B 08/10 TLU 201 1.750 1.000 1.000 1.750 08/10 TLU 202 1.750 1.000 1.500 2.250 08/10 TLU 203 2.000 1.250 1.250 2.000 08/10 TLU 204 2.250 1.500 1.000 1.750 08/10 TLU 205 2.250 1.500 1.500 2.250 08/10 TLU 206 2.625 1.875 1.875 2.625 ITEM NO. A B 08/10 SSU 221 1.377 1.377 08/10 SSU 222 1.377 1.877 08/10 SSU 223 1.877 1.377 08/10 SSU 224 1.877 1.877 08/10 SSU 225 1.877 2.377 08/10 SSU 226 2.377 1.877 08/10 SSU 227 2.377 2.377 08/10 SSU 228 2.377 2.877 08/10 SSU 229 2.877 2.377 08/10 SSU 230 2.877 2.877 Standard Solid Construction Standard Laminated Construction T-Style Laminated Construction ITEM NO. A A2 B2 B 08/10 TSU 241 1.750 1.000 1.000 1.750 08/10 TSU 242 1.750 1.000 1.500 2.250 08/10 TSU 243 2.000 1.250 1.250 2.000 08/10 TSU 244 2.250 1.500 1.000 1.750 08/10 TSU 245 2.250 1.500 1.500 2.250 08/10 TSU 246 2.625 1.875 1.875 2.625 T-Style Solid Construction Companion Interchangeable Insert Molds Ordering information for frame and companion insert molds can be found in the front of this catalog. 1 Frame clamps at this end of insert mold and ejector plates are flush with this end of insert. 2 Support post not supplied. Grind +.001 to +.002 higher than height of ejection (see page UF 39). 3 Thicker plate optional. T-Style Solid or Laminated: 7.85 x 9.0 Standard Laminated: 5.0 x 9.0 .230 A B .360 .246 Ø .375 2 3 .750 .750 .360 .437 .437 8.88 9.000 4.996 5.456 ±.001 Ejector Half .562 Offset 1 2.625 Ejection 4.00 Central .230 A .246 Ø .375 .437 .437 8.88 9.000 4.996 5.456 ±.001 Ejector Half .562 Offset 1 4.00 Central B .360 2 3 .360 2.625 Ejection .75 A2 .75 B2 A B .360 .246 Ø .500 3 .75 .360 B2 .562 4.68 .75 4.996 5.456 ±.001 A2 .562 .31 8.88 9.000 7.850 Ejector Half 2 2.625 Ejection 4.00 Central 1 Ø 5/16 Dowel .687 Offset .230 *O degree - 15 minute taper slot to accommodate sleeve ejection retainer plate. Slot tapers from .287 to .248 in 9.000 length. UF 321 Frame Upper – Side View UF 321 Frame Upper – Top View UF 321 Frame Lower – Side View UF 321 Frame Lower – Top View LR171 Ø S 3.990 .60 SB2025-88 Ø O Ø 2.5 R UC 3816 1.35 .60 .75 .44 .187 1.50 3.375 2.366 4.500 2.756 3.925 3.375 2.366 1/2-13 THD (18) 4.500 10.00 9.00 1.00 .500 7.85 5.000 +.002 –.000 3/8 x 5° Lead 3/8-16 THD .250 4.25 Ø 1.126 .25 .81 .253 .75 3.97 2.625 3.37 ±.0005 .287 .60 * .50
UF 10 Enhanced series mold Inserts SOLID 0.38x5° 多哪图画 e Provides room for thicker pocket walls Reduces machine setup time by providing more surface area for Ejector plates are bolted together for 3.250 Compatible with the MUD Quick-Change U Frame 4000 h Installed with four leader pins and 4.996 5.456 ushings, four return pins and eyebolt holes All-in-one post guides ejection retains MUD500062 230 the ejection system and provides support without the use of additional P3-1710-15 support pillars 0.40 Tapped hole for insert removal B3-1710 Finish-ground parting line plates 1877:001 MUD5000-62 Optional. 480 thick ejector plates 08/09 Series mold inserts available in 0375 DME#2and鹅3 type steels Other sizes available on request 阳中 1/-20x3/8 *000 PPAB-5(2) 2626 AGP826(2 AGB360(2 U.s.80o-626-6653 Canada00-387-6600mwww.dme.net
Enhanced Series Mold Inserts SOLID UF 10 U.S. 800-626-6653 Canada 800-387-6600 ■ www.dme.net 2.728 3.500 (2) Return Pin & Ejector Plate SHCS 2.498 2.061 1.219 (4) 0.000 1.750 (4) 2.498 2.728 3.563 (2) Return Pin & Ejector Plate SHCS 4.000 3.875 3.438 3.125 4.000 3.250 0.000 0.000 0.000 3.438 3.563 0.47 (2) 0.38 x 5° Lead 4.996 5.456 +.005 –.000 8.000 0.40 1/4-20 .230 MUD5000-62 0.246 MUD5000-62 0.375 0.360 0.360 P3-1710-15 1/4-20 x 3/8 SHCS (4) B3-1710 0.752 1.877 ±.001 1.877 ±.001 +.001 –.000 2.626 AGB-360 (2) AGP-826 (2) PPAB-5 (2) 5/16-18 x 3 SHCS (2) 1.36 • Provides room for thicker pocket walls • Reduces machine setup time by providing more surface area for clamping • Ejector plates are bolted together for maximum convenience • Compatible with the MUD Quick-Change U Frame • Installed with four leader pins and bushings, four return pins and eyebolt holes • All-in-one post guides ejection retains the ejection system and provides support without the use of additional support pillars • Tapped hole for insert removal • Finish-ground parting line plates • Optional .480 thick ejector plates • 08/09 Series mold inserts available in D-M-E #2 and #3 type steels • Other sizes available on request