Availableonlineatwww.sciencedirect.com Reports: A Review ournal .. Science Direct ELSEVIER R Materials Science and Engineering R 60(2008)1-51 wwelsevier.com/locate/mser Growth of nanowires N. Wang ,, Y Cai, R.Q. Zhang Department of Physics and the institute of Nano Science and Technology, the Hong Kong University of Science and Technology, Hong Kong, China Center of Super-Diamond and Advanced Films(COSDAF)& Department of Physics and Materials Science City Universiry of Hong Kong, Hong Kong, Chin Available online 5 March 2008 Abstract The tremendous interest in nanoscale structures such as quantum dots(zero-dimension)and wires(quasi-one-dimension )stems from their size- dependent properties. One-dimensional (1D) semiconductor nanostructures are of particular interest because of their potential applications in nanoscale electronic and optoelectronic devices. For ID semiconductor nanomaterials to have wide practical application, however, several areas require further development. In particular, the fabrication of desired ID nanomaterials with tailored atomic structures and their assembly into functional devices are still major challenges for nanotechnologists. In this review, we focus on the status of research on the formation of nanowire structures via highly anisotropic growth of nanocrystals of semiconductor and metal oxide materials with an emphasis on the structural characterization of the nucleation, initial growth, defects and interface structures, as well as on theoretical analyses of nanocrystal formation, reactivity and stability. We review various methods used and mechanisms involved to generate lD nanostructures from different material systems through self-organized growth techniques including vapor-liquid-solid growth, oxide-assisted chemical vapor deposition (without a metal catalyst), laser ablation, thermal evaporation, metal-catalyzed molecular beam epitaxy, chemical beam epitaxy and hydrothermal reaction. ID nanostructures grown by these technologies have been observed to exhibit unusual growth phenomena and unexpected properties, e.g., diameter dependent and temperature-dependent growth directions, structural transformation by enhanced photothermal effects and phase transformation induced by the point contact reaction in ultra-thin semiconductor nanowires. Recent progress in controlling growth directions, defects, interface structures, structural transformation, contacts and hetero- junctions in lD nanostructures is addressed. Also reviewed are the quantitative explorations and predictions of some challenging ID nanostructures and descriptions of the growth mechanisms of ID nanostructures, based on the energetic, dynamic and kinetic behaviors of the building block nanostructures and their surfaces and/or interfaces C 2008 Elsevier B V. All rights reserved Contents Introduction 2 2. Growth technologies for nanowires 2.1. Vapor-liquid-solid(VLS)technique 2. 2. Laser-assisted growth 5 2.3. Thermal evaporation 6 4. Metal-catalyzed molecular-beam epita 2.5. Solution method 3. Growth mechanisms of nanowires 9 3. 2. Vapor-solid growth 14 3.2.1. Internal anisotropic surfaces 3.2.2. Crystal defects 3.2.3. Self-catalytic growth front matter C 2008 Elsevier B V. All rights reserved. 10.1016 j.mser.2008.01.001
Growth of nanowires N. Wang a, *, Y. Cai a , R.Q. Zhang b a Department of Physics and the Institute of Nano Science and Technology, the Hong Kong University of Science and Technology, Hong Kong, China bCenter of Super-Diamond and Advanced Films (COSDAF) & Department of Physics and Materials Science, City University of Hong Kong, Hong Kong, China Available online 5 March 2008 Abstract The tremendous interest in nanoscale structures such as quantum dots (zero-dimension) and wires (quasi-one-dimension) stems from their sizedependent properties. One-dimensional (1D) semiconductor nanostructures are of particular interest because of their potential applications in nanoscale electronic and optoelectronic devices. For 1D semiconductor nanomaterials to have wide practical application, however, several areas require further development. In particular, the fabrication of desired 1D nanomaterials with tailored atomic structures and their assembly into functional devices are still major challenges for nanotechnologists. In this review, we focus on the status of research on the formation of nanowire structures via highly anisotropic growth of nanocrystals of semiconductor and metal oxide materials with an emphasis on the structural characterization of the nucleation, initial growth, defects and interface structures, as well as on theoretical analyses of nanocrystal formation, reactivity and stability. We review various methods used and mechanisms involved to generate 1D nanostructures from different material systems through self-organized growth techniques including vapor–liquid–solid growth, oxide-assisted chemical vapor deposition (without a metal catalyst), laser ablation, thermal evaporation, metal-catalyzed molecular beam epitaxy, chemical beam epitaxy and hydrothermal reaction. 1D nanostructures grown by these technologies have been observed to exhibit unusual growth phenomena and unexpected properties, e.g., diameterdependent and temperature-dependent growth directions, structural transformation by enhanced photothermal effects and phase transformation induced by the point contact reaction in ultra-thin semiconductor nanowires. Recent progress in controlling growth directions, defects, interface structures, structural transformation, contacts and hetero-junctions in 1D nanostructures is addressed. Also reviewed are the quantitative explorations and predictions of some challenging 1D nanostructures and descriptions of the growth mechanisms of 1D nanostructures, based on the energetic, dynamic and kinetic behaviors of the building block nanostructures and their surfaces and/or interfaces. # 2008 Elsevier B.V. All rights reserved. Contents 1. Introduction . .................................................................................. 2 2. Growth technologies for nanowires . . ................................................................. 3 2.1. Vapor–liquid–solid (VLS) technique . ............................................................. 3 2.2. Laser-assisted growth . . . ..................................................................... 5 2.3. Thermal evaporation ......................................................................... 6 2.4. Metal-catalyzed molecular-beam epitaxy . . ......................................................... 7 2.5. Solution methods . .......................................................................... 9 3. Growth mechanisms of nanowires . . . ................................................................. 9 3.1. Metal-catalyzed growth . . ..................................................................... 9 3.2. Vapor–solid growth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.2.1. Internal anisotropic surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.2.2. Crystal defects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.2.3. Self-catalytic growth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 www.elsevier.com/locate/mser Available online at www.sciencedirect.com Materials Science and Engineering R 60 (2008) 1–51 * Corresponding author. Tel.: +852 2358 7489; fax: +852 2358 1652. E-mail address: phwang@ust.hk (N. Wang). 0927-796X/$ – see front matter # 2008 Elsevier B.V. All rights reserved. doi:10.1016/j.mser.2008.01.001
N. Wang et al /Materials Science and Engineering R 60(2008)1-51 3.3. Oxide-assisted growth 3.3.1. Kinetics and reactivity of silicon oxide in nucleation and growth 3.3.2. Effect of defects in ID growth 3.3.3. Effect of extermal electrical field in lD growth 3. 4. Self-assembly growth from solution 3.4. 1. Solution-liquid-solid (SLS) growth from seeds 9000 3.4.2. Self-assembly oriented attachment growth 3.4.3. Anisotropic growth of crystals by kinetic control 4. Controlled growth of nanowires 4. 1. Control of structures, growth direction and defects in nanowires 4.1.1. Interface structures 4. 1.2. The growth direction of VLS nanowires 4. 1.3. Defects in 4.1.4. From nanowire to nanoribbon 4.2. Structural transformation in nanowires 4.2.1 Surface relaxation and saturation of zinc oxide nanowires 4.2. 2. The stability of Si nar 4.2.3. Optical rapid annealing effect 4.3. Contacts and heterostructures in nanowires 23832245779 4.3.1. Metal-semiconductor contacts 4.3. 2. Heterostructures in nanowires 5. Other challenging nanowire structur 5.1. Non-tetrahedral Si nanowires 5.2. Oxide nanowires 5.2.1. Silicon oxide nanowires 5.2.2. Silicon dioxide tube-like nanowires 5.2. 3. Zinc oxide tube-like nanowire 46 6. Concluding remarks Acknowledgements 1. ntroduction nanostructures formed"naturally"(also called self-organized growth)without the aids of ex situ techniques, such as chemical In the physics structures, quantum effects play etching, are desirable not only in fundamental research but also n increasingly role [1]. Quantum wires have in future nanodevice design and fabrication demonstrated int trical transport properties that are In this paper, various novel technologies for synthesizing not seen in bulk his is because, in quantum wires, nanowires are reviewed. A well-known self-organized growth electrons could be quantum-confined laterally and thus could mechanism for creating nanowires is the vapor-liquid-solid occupy discrete energy levels that are different from the energy (VLS) process(also known as metal catalytic growth [5]). This bands found in bulk materials. Due to low electron density and technique can produce free-standing crystalline nanowires of low effective mass, the quantized conductivity is more easily semiconductor and metal oxide materials with fully controlled observed in semiconductors, e. g, Si and GaAs, than in metals nucleation sites and diameters from pre-formed metal catalysts 2]. In addition to the opportunity to describe the new physics Since the 1960s, semiconductor whiskers grown by this demonstrated by nanowires, much effort has been devoted to technique [5, 6] have been extensively studied. In recent years, fabricating high-quality semiconductor nanowires by employ- various new techniques have been developed to realize ID ing different techniques because of the importance of nanostructures, such as laser-assisted chemical vapor deposi semiconductor materials to the electronics industry. The most tion(CVD)[7-10), oxide-assisted CVD(without a metal pular technique used to fabricate semiconductor artificial catalyst)[11], thermal CVD [12], metal-catalyzed molecular structures with feature sizes in the sub-100 nm range is beam epitaxy (MBE)[13-15] and chemical beam epitaxy lithography (3, 4], which involves tedious processes of ( CBE)[16]. Though the number of various kinds of ID hotoresist removal, chemical or ion-beam etching and surface nanostructures fabricated via different techniques increase passivation, etc. On semiconductor nanostructures, etching dramatically every year, our understanding of the basic process processes always lead to significant surface damage, and thus of ID nanostructure formation has not reached maturity. How to urface states are introduced to the nanostructures. Such fabricate desired id nanomaterials with tailored atomic damage may not be serious for the structures in the micrometer structures and how to integrate functional nanostructures into range. However, structures with dimensions in the nanometer devices are still challenging issues for materials scientists For very sensitive to the surface states or impurities ID semiconductor nanomaterials to have wide practical induced by fabrication processes. One-dimensional(ID) applications, however, many areas require further pursuing
3.3. Oxide-assisted growth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 3.3.1. Kinetics and reactivity of silicon oxide in nucleation and growth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 3.3.2. Effect of defects in 1D growth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.3.3. Effect of external electrical field in 1D growth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3.4. Self-assembly growth from solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 3.4.1. Solution-liquid-solid (SLS) growth from seeds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 3.4.2. Self-assembly oriented attachment growth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 3.4.3. Anisotropic growth of crystals by kinetic control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 4. Controlled growth of nanowires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4.1. Control of structures, growth direction and defects in nanowires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4.1.1. Interface structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4.1.2. The growth direction of VLS nanowires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4.1.3. Defects in nanowires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 4.1.4. From nanowire to nanoribbon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 4.2. Structural transformation in nanowires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 4.2.1. Surface relaxation and saturation of zinc oxide nanowires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 4.2.2. The stability of Si nanowires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 4.2.3. Optical rapid annealing effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 4.3. Contacts and heterostructures in nanowires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 4.3.1. Metal-semiconductor contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 4.3.2. Heterostructures in nanowires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 5. Other challenging nanowire structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 5.1. Non-tetrahedral Si nanowires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 5.2. Oxide nanowires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 5.2.1. Silicon oxide nanowires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 5.2.2. Silicon dioxide tube-like nanowires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 5.2.3. Zinc oxide tube-like nanowires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 6. Concluding remarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 1. Introduction In the physics of nanoscale structures, quantum effects play an increasingly prominent role [1]. Quantum wires have demonstrated interesting electrical transport properties that are not seen in bulk materials. This is because, in quantum wires, electrons could be quantum-confined laterally and thus could occupy discrete energy levels that are different from the energy bands found in bulk materials. Due to low electron density and low effective mass, the quantized conductivity is more easily observed in semiconductors, e.g., Si and GaAs, than in metals [2]. In addition to the opportunity to describe the new physics demonstrated by nanowires, much effort has been devoted to fabricating high-quality semiconductor nanowires by employing different techniques because of the importance of semiconductor materials to the electronics industry. The most popular technique used to fabricate semiconductor artificial structures with feature sizes in the sub-100 nm range is lithography [3,4], which involves tedious processes of photoresist removal, chemical or ion-beam etching and surface passivation, etc. On semiconductor nanostructures, etching processes always lead to significant surface damage, and thus surface states are introduced to the nanostructures. Such damage may not be serious for the structures in the micrometer range. However, structures with dimensions in the nanometer range are very sensitive to the surface states or impurities induced by fabrication processes. One-dimensional (1D) nanostructures formed ‘‘naturally’’ (also called self-organized growth) without the aids of ex situ techniques, such as chemical etching, are desirable not only in fundamental research but also in future nanodevice design and fabrication. In this paper, various novel technologies for synthesizing nanowires are reviewed. A well-known self-organized growth mechanism for creating nanowires is the vapor–liquid–solid (VLS) process (also known as metal catalytic growth [5]). This technique can produce free-standing crystalline nanowires of semiconductor and metal oxide materials with fully controlled nucleation sites and diameters from pre-formed metal catalysts. Since the 1960s, semiconductor whiskers grown by this technique [5,6] have been extensively studied. In recent years, various new techniques have been developed to realize 1D nanostructures, such as laser-assisted chemical vapor deposition (CVD) [7–10], oxide-assisted CVD (without a metal catalyst) [11], thermal CVD [12], metal-catalyzed molecular beam epitaxy (MBE) [13–15] and chemical beam epitaxy (CBE) [16]. Though the number of various kinds of 1D nanostructures fabricated via different techniques increases dramatically every year, our understanding of the basic process of 1D nanostructure formation has not reached maturity. How to fabricate desired 1D nanomaterials with tailored atomic structures and how to integrate functional nanostructures into devices are still challenging issues for materials scientists. For 1D semiconductor nanomaterials to have wide practical applications, however, many areas require further pursuing. 2 N. Wang et al. / Materials Science and Engineering R 60 (2008) 1–51
N. Wang et al. /Materials Science and Engineering R 60 (2008)1-51 This review focuses on describing the status of research on the surface [6]. At a temperature above 363C, Au particles can formation of semiconductor and metal oxide nanowires. It form Si-Au eutectic droplets on Si surfaces, and the reduction consists of four sections. After a brief introduction, the first of Si occurs at the Au-Si droplets due to a catalytic effect. The section introduces the growth technologies currently employed Au-Si dro pets abso orb Si from the vapor pl to synthesize nanowires with an emphasis on advances in the supersaturated state. Since the melting point of Si(1414C)is newly developed techniques of metal-catalyzed MBE and CBe much higher than that of the eutectic alloy, Si atoms precipitate by which high-quality ultra-thin nanowire structures have been from the supersaturated droplets and bond at the liquid-solid fabricated. These techniques allow high levels of control over interface, and the liquid droplet rises from the Si substrate atomic structures, chemical composition, defects, doping surface. The absorption, diffusion and precipitation processes states, junctions, and so forth. We next discuss several novel of Si as schematically shown by the path 1-2-3 in Fig. 1(c) nucleation and growth mechanisms and theoretical analyses of involve vapor, liquid and solid phases. The typical feature of the the formation, reactivity and stability of nanocrystals. The VLS reaction is its low activation energy compared with normal initial alloying process of metal catalysts, growth of nanowire vapor-solid growth. The whiskers grow only in the areas seeded nuclei, changes in nanowire shapes and diameters as well as by metal catalysts, and their diameters are mainly determined deposition of source materials are described in the second by the sizes of the catalysts. The Vls method can result in section. In the third section, we describe the controlled growth unidirectional growth of many materials [6]. It has become a and structures of nanowires. Recent progress in controlling widely used technique for fabricating a variety of ID growth directions, defects, interface structures, structural nanomaterials that include elemental semiconductors [6- transformation, contacts and hetero-junctions is addressed In 8, 17-23], II-VI semiconductors [24-26], Ill-V semiconduc- the last section, we describe some theoretical nanowire tors 27-41, oxides [4247, nitrides[48]and carbides [ 49, 50] structures that have not yet been observed or are challenging The experimental setup of the VLs reaction has been to synthesis eported in previous work [5,6]. In brief, for Si nanowire growth, the sources can be Sih, mixed in H2 at a typical ratio of 2. Growth technologies for nanowires 1: 10. The reaction gases have to be diluted to about 2% in an Ar atmosphere. The pressure for the reaction is about 200 Torr, and 2.1. Vapor-liquid-solid (VLS) technique he flow rate is kept at 1500 sccm. Au nanoparticles can be prepared simply by first depositing an Au thin film on an Si The VLS technique was first described by Wagner and Ellis substrate using sputtering or thermal evaporation and then 5] in 1964. They used Au particles as catalysts to grow annealing the thin film to form droplets. Fig. 2(a) shows crystalline semiconductor whiskers from vapor sources such as uniform Au nanoparticles formed by annealing an Au thin film SiCl4 or SiH4. The principle for Si whisker growth is (thickness =l nm) at 500C. A thick film results in large thematically shown in Fig. 1(a). The Au particles deposited diameters of Au particles. Au particles arrays can be prepared on the surface of an Si substrate react first with Si to form Au-Si by lithography techniques. Fig. 2(b) shows an Au disc array alloy droplets at a certain temperature. As shown in the Au-Si prepared by e-beam lithography. The thickness of the Au phase diagram in Fig. 1(b), the melting temperature of the Au- pattern is critical to the final sizes of the nanoparticles Si alloy at the eutectic point is very low(about 363C at an generated by the subsequent annealing. Au films that are too Au: Si ratio of 4: 1)compared with that of Au or Si. Au and Si thin always result in splitting of the Au pattern(Fig. 2(c)). A can form a solid solution for all Si content(0-100%). In the proper treatment of the substrate surface by chemical etching case of Si deposition from the vapor mixture of SiCl4 and H2, and cleaning can result in the catalyst totally wetting the the reaction between SiCl4 and H2 happens at a temperature substrate surface(see Fig. 3(a)), which is important for later above 800C without the assistance of catalysts. Below this growth of the nanowires epitaxially on the substrate. Because of temperature, almost no deposition of Si occurs on the substrate the oxide layer on the substrate surface or impurities on the Si Whisker Au-Si uSi)1115 Substrate Fig. 1. Schematic illustration of Si whisker growth from vapor phases via Au-Si catalytic droplets. (a) The Au-Si droplet formed on an Si substrate catalyzes the whisker growth: (b)the Au-Si phase diagram. (c)The diffusion path of the source materials through a metal droplet; (d) the whisker growth can be catalyzed with
This review focuses on describing the status of research on the formation of semiconductor and metal oxide nanowires. It consists of four sections. After a brief introduction, the first section introduces the growth technologies currently employed to synthesize nanowires with an emphasis on advances in the newly developed techniques of metal-catalyzed MBE and CBE by which high-quality ultra-thin nanowire structures have been fabricated. These techniques allow high levels of control over atomic structures, chemical composition, defects, doping states, junctions, and so forth. We next discuss several novel nucleation and growth mechanisms and theoretical analyses of the formation, reactivity and stability of nanocrystals. The initial alloying process of metal catalysts, growth of nanowire nuclei, changes in nanowire shapes and diameters as well as deposition of source materials are described in the second section. In the third section, we describe the controlled growth and structures of nanowires. Recent progress in controlling growth directions, defects, interface structures, structural transformation, contacts and hetero-junctions is addressed. In the last section, we describe some theoretical nanowire structures that have not yet been observed or are challenging to synthesis. 2. Growth technologies for nanowires 2.1. Vapor–liquid–solid (VLS) technique The VLS technique was first described by Wagner and Ellis [5] in 1964. They used Au particles as catalysts to grow crystalline semiconductor whiskers from vapor sources such as SiCl4 or SiH4. The principle for Si whisker growth is schematically shown in Fig. 1(a). The Au particles deposited on the surface of an Si substrate react first with Si to form Au–Si alloy droplets at a certain temperature. As shown in the Au–Si phase diagram in Fig. 1(b), the melting temperature of the Au– Si alloy at the eutectic point is very low (about 363 8C at an Au:Si ratio of 4:1) compared with that of Au or Si. Au and Si can form a solid solution for all Si content (0–100%). In the case of Si deposition from the vapor mixture of SiCl4 and H2, the reaction between SiCl4 and H2 happens at a temperature above 800 8C without the assistance of catalysts. Below this temperature, almost no deposition of Si occurs on the substrate surface [6]. At a temperature above 363 8C, Au particles can form Si–Au eutectic droplets on Si surfaces, and the reduction of Si occurs at the Au–Si droplets due to a catalytic effect. The Au–Si droplets absorb Si from the vapor phase resulting in a supersaturated state. Since the melting point of Si (1414 8C) is much higher than that of the eutectic alloy, Si atoms precipitate from the supersaturated droplets and bond at the liquid–solid interface, and the liquid droplet rises from the Si substrate surface. The absorption, diffusion and precipitation processes of Si as schematically shown by the path 1 ! 2 ! 3 in Fig. 1(c) involve vapor, liquid and solid phases. The typical feature of the VLS reaction is its low activation energy compared with normal vapor–solid growth. The whiskers grow only in the areas seeded by metal catalysts, and their diameters are mainly determined by the sizes of the catalysts. The VLS method can result in unidirectional growth of many materials [6]. It has become a widely used technique for fabricating a variety of 1D nanomaterials that include elemental semiconductors [6– 8,17–23], II–VI semiconductors [24–26], III–V semiconductors [27–41], oxides [42–47], nitrides [48] and carbides [49,50]. The experimental setup of the VLS reaction has been reported in previous work [5,6]. In brief, for Si nanowire growth, the sources can be SiH4 mixed in H2 at a typical ratio of 1:10. The reaction gases have to be diluted to about 2% in an Ar atmosphere. The pressure for the reaction is about 200 Torr, and the flow rate is kept at 1500 sccm. Au nanoparticles can be prepared simply by first depositing an Au thin film on an Si substrate using sputtering or thermal evaporation and then annealing the thin film to form droplets. Fig. 2(a) shows uniform Au nanoparticles formed by annealing an Au thin film (thickness = 1 nm) at 500 8C. A thick film results in large diameters of Au particles. Au particles arrays can be prepared by lithography techniques. Fig. 2(b) shows an Au disc array prepared by e-beam lithography. The thickness of the Au pattern is critical to the final sizes of the nanoparticles generated by the subsequent annealing. Au films that are too thin always result in splitting of the Au pattern (Fig. 2(c)). A proper treatment of the substrate surface by chemical etching and cleaning can result in the catalyst totally wetting the substrate surface (see Fig. 3(a)), which is important for later growth of the nanowires epitaxially on the substrate. Because of the oxide layer on the substrate surface or impurities on the Fig. 1. Schematic illustration of Si whisker growth from vapor phases via Au–Si catalytic droplets. (a) The Au–Si droplet formed on an Si substrate catalyzes the whisker growth; (b) the Au–Si phase diagram. (c) The diffusion path of the source materials through a metal droplet; (d) the whisker growth can be catalyzed with a solid catalyst. N. Wang et al. / Materials Science and Engineering R 60 (2008) 1–51 3
N. Wang et al/Materials Science and Engineering R 60(2008)1-51 Fig. 2.(a) Au catalysts prepared by annealing a thin Au film.( b)Au prepared by e-beam lithography. (c) Splitting of the Au particles by annealing catalyst surface induced by the lithography technique, Au Under isothermal conditions, the crystalline structures of Si catalysts may not wet the substrate surface. In this case, Si whiskers are generally perfect, though steps and facets occur on nanowires may not have orientation relationship with the the whiskers'surfaces Twinning structures and twin-dendrites substrate and grow along random directions(Fig 3(b)). For Si (or branched whiskers) have been frequently observed in the nanowires with diameters larger than 20 nm, their growth is whiskers. Though the cross-section of most whiskers is round enerally along the(1 11) direction. Thin Si nanowires with (determined by the metal droplets), ribbon-like whiskers with a diameters smaller than 20 nm, however, show interesting rectangular cross-section often coexist and show the(11 1or growth behaviors for example the diameter-dependent and (1 1 2) growth direction [17]. Dislocations or other crystalline temperature-dependent growth direction( see details in Section defects are not essential for the growth of the whiskers via the 4.1) VLS method. In different semiconductor material systems, Before growing Si nanowires, activation of Au nanoparticles whiskers with similar morphologies and structures have been may be needed. An inactivated Au particle will not lead to fabricated by the VLS reaction and a variety of whisker forms nanowire growth. The activation of Au-Si alloy droplets can be have been obtained [6]. Although the VLS technique has been carried out in Ar or H2 atmospheres. We have found that plasma widely used for the fabrication of nanowires in recent years, the treatment is effective for cleaning and activating the surfaces of real absorption, reaction and diffusion processes of source Au catalysts. HCI mixed in the reaction gases can also atoms through the catalyst are complicated and largely depend effectively activate Au particles. However, the activation on the experimental conditions and the material systems [52- temperature largely relies on the diameters of Au catalysts For 54]. Many experiments have shown the deviation of some large Au catalysts(diameter >50 nm), the activation tempera- nanowire growth from the classical VLS mechanism. For tures can be 800C or higher. Large Au catalysts can easily wet example, it has been observed that nanowires of Ge [18, 19], Si a Si substrate at sufficiently high temperatures and thus Si [22], GaAs [27] and InAs [28] can grow even at temperatures nanowires grow epitaxially even on an untreated substrate. In below their eutectic points. There has been a long-standing the growth of thin Si nanowires(diameter <20 nm), the growth debate on whether the metal catalysts in these cases are solid temperatures are about 500C. Too high activation tempera- particles(see Fig. 1(d))or liquid droplets [54]. There are two tures may cause evaporation of the catalysts. The vacuum uncertainties in this debate: (1)because of the nanosize condition is another critical experimental parameter that affects effect, the melting temperatures of nanoparticles are always nanowire growth. Low vacuum conditions may cause lower than those of bulk materials and(2)it is not possible to evaporation of Si from the substrate surface and thus result measure the real temperature at the catalyst tips. In fact, in some in a rough surface cases, nanosized metal droplets are in a partially molten state Au Catalyst Si 50nm 20um Fig. 3. (a)An Au catalyst reacts with the substrate after the activation treatment. (b) Si nanowires grow in different directions
catalyst surface induced by the lithography technique, Au catalysts may not wet the substrate surface. In this case, Si nanowires may not have orientation relationship with the substrate and grow along random directions (Fig. 3(b)). For Si nanowires with diameters larger than 20 nm, their growth is generally along the h111i direction. Thin Si nanowires with diameters smaller than 20 nm, however, show interesting growth behaviors for example the diameter-dependent and temperature-dependent growth direction (see details in Section 4.1). Before growing Si nanowires, activation of Au nanoparticles may be needed. An inactivated Au particle will not lead to nanowire growth. The activation of Au–Si alloy droplets can be carried out in Ar or H2 atmospheres. We have found that plasma treatment is effective for cleaning and activating the surfaces of Au catalysts. HCl mixed in the reaction gases can also effectively activate Au particles. However, the activation temperature largely relies on the diameters of Au catalysts. For large Au catalysts (diameter > 50 nm), the activation temperatures can be 800 8C or higher. Large Au catalysts can easily wet a Si substrate at sufficiently high temperatures and thus Si nanowires grow epitaxially even on an untreated substrate. In the growth of thin Si nanowires (diameter <20 nm), the growth temperatures are about 500 8C. Too high activation temperatures may cause evaporation of the catalysts. The vacuum condition is another critical experimental parameter that affects nanowire growth. Low vacuum conditions may cause evaporation of Si from the substrate surface and thus result in a rough surface. Under isothermal conditions, the crystalline structures of Si whiskers are generally perfect, though steps and facets occur on the whiskers’ surfaces. Twinning structures and twin-dendrites (or branched whiskers) have been frequently observed in the whiskers. Though the cross-section of most whiskers is round (determined by the metal droplets), ribbon-like whiskers with a rectangular cross-section often coexist and show the h111i or h112i growth direction [17]. Dislocations or other crystalline defects are not essential for the growth of the whiskers via the VLS method. In different semiconductor material systems, whiskers with similar morphologies and structures have been fabricated by the VLS reaction and a variety of whisker forms have been obtained [6]. Although the VLS technique has been widely used for the fabrication of nanowires in recent years, the real absorption, reaction and diffusion processes of source atoms through the catalyst are complicated and largely depend on the experimental conditions and the material systems [52– 54]. Many experiments have shown the deviation of some nanowire growth from the classical VLS mechanism. For example, it has been observed that nanowires of Ge [18,19], Si [22], GaAs [27] and InAs [28] can grow even at temperatures below their eutectic points. There has been a long-standing debate on whether the metal catalysts in these cases are solid particles (see Fig. 1(d)) or liquid droplets [54]. There are two main uncertainties in this debate: (1) because of the nanosize effect, the melting temperatures of nanoparticles are always lower than those of bulk materials and (2) it is not possible to measure the real temperature at the catalyst tips. In fact, in some cases, nanosized metal droplets are in a partially molten state Fig. 2. (a) Au catalysts prepared by annealing a thin Au film. (b) Au patterns prepared by e-beam lithography. (c) Splitting of the Au particles by annealing. Fig. 3. (a) An Au catalyst reacts with the substrate after the activation treatment. (b) Si nanowires grow in different directions. 4 N. Wang et al. / Materials Science and Engineering R 60 (2008) 1–51
N. Wang et al. /Materials Science and Engineering R 60 (2008)1-51 51]. The surface and interface regions are liquid, while the technique is particularly useful in the synthesis of nanowires with cores of the droplets are solid a high-melting temperature, such as SiC nanowires[56]. It is also The VLS mechanism is very successful in generating large a very effective method in synthesizing nanowires with multi- quantities of ID nanomaterials(single nanowires and hetero- components and doping nanowires during growth. The vaporized ructured nanowires) with uniform crystalline structures not molecules(or clusters)by the high power laser have high kinetic only in semiconductors but also in oxide, nitride and other energy(about 100 eV), and this largely enhances the chemical material systems. However, it seems to be difficult to grow reaction, e.g., the reaction with oxygen or other gases, and thu metal nanowires by the VLS method. The disadvantage of the can largely improve the crystal quality of the nanowires at a low VLS method may be the contamination caused by the necessary substrate temperature. This special technique has many practical use of a metal particle as the catalyst. This may result in the uses for the control of the stoichiometries of nanowires. For change in the nanowires properties. However, by selecting an example, ZnO nanowires grown by thermal CVd always have appropriate catalyst, the affection of the contamination for oxygen vacancies and other defects that cau on- specific properties of the nanowire can be minimized. band edge emission) and electrical (low conductivity compared with bulk Zno crystals) properties. These defects cannot be 2.2. Laser-assisted growth easily eliminated even by annealing in oxygen after nanowire growth. Zno nanowires synthesized by laser ablation, however, Among the various techniques developed to synthesize ultra- generally show better optical properties. Another example is that thin nanowires, of particular interest is the laser ablation of indium oxide nanowires synthesized by laser ablation have a metal-containing solid targets or similar techniques [7-10], by significantly high mobility [57] which bulk-quantity nanowires can be readily obtained directly Fig. 4 is a schematic of the experimental setup of the laser from solid source materials. When using metal catalysts, for ablation technique. The laser used in the experiment can be any example, for the synthesis of Si nanowires, this method is high-power pulsed laser, e. g, a Nd: YAG laser [7], an interfered suggested to rely on the VLS mechanism, whereby the vapor(or femto-second laser[58]or an excimer laser [59]. The synthesis of gaseous clusters) generated by laser ablation dissolves in a Si nanowires by the experiment reported in Refs. [ 10,59, 60] was molten metal catalyst and then crystallizes to form nanowires. carried out using a high-power KrF excimer pulsed laser Ultrasmall nanoparticles of metals or metal silicides in large (248 nm, 10 Hz, 400 mJ/pulse)to ablate a target in an evacuated quantities are rather easy to obtain from the high temperature (500 Torr) quartz tube with Ar (50 sccm) flowing through the induced by laser ablation. Assisted by laser ablation, these tube. Otherinert gases, such as He, H2 and N2, can also be used as nanoparticles act as the critical catalyst for the nucleation and the ambient gases. The use of different ambient gases may growth of nanowires influence the diameters of the nanowires and affects their optical The laser-assisted method has unique advantages over other properties [60]. The temperature around the target materials in growth techniques in synthesizing nanowires containing com- the experiment was about 1200C. The target was highly pure Si plex chemical compositions. This is because no matter how many powder mixed with Fe, Ni, or Co(about 0. 5%o). The laser beam elements are involved, it is not necessary to prepare the target(or (1 mm x 3 mm)was focused on the target surface. Si nanowire the source materials)in a crystalline form. A simple mixture of products( sponge-like, dark yellow in color as shown in Fig. 5(a)) the elements is good enough as the source material. The source formed on the Sisubstrate or the inner wall of the quartz tube near materials are ablated into a vapor phase, which may have the the water-cooled finger after I h of laser ablation. The same composition as the source materials. The vapor phase can temperature of the area around the substrate where the nanowire e easily transferred to the substrate where nanowires nucleate grew was approximately 900-1000'C The growth rate of the Si and grow. A high-energy laser can ablate solid materials in an nanowires was about 10-80 um/h ultra short time and vaporize the materials in a non-thermo By laser ablation, the metal powder is evaporated out of the equilibrium process, also called congruent evaporation [55]. This target to form clusters. They are in a semi-liquid state and serve Window Furnace Cold finger →Ar(He) 500To 1200°C Evaporation target Pumping Fig. 4. Experimental setup for the synthesis of Si nanowires by laser ablation( Courtesy of Prof. I. Bello)
[51]. The surface and interface regions are liquid, while the cores of the droplets are solid. The VLS mechanism is very successful in generating large quantities of 1D nanomaterials (single nanowires and heterostructured nanowires) with uniform crystalline structures not only in semiconductors but also in oxide, nitride and other material systems. However, it seems to be difficult to grow metal nanowires by the VLS method. The disadvantage of the VLS method may be the contamination caused by the necessary use of a metal particle as the catalyst. This may result in the change in the nanowire’s properties. However, by selecting an appropriate catalyst, the affection of the contamination for specific properties of the nanowire can be minimized. 2.2. Laser-assisted growth Among the various techniques developed to synthesize ultrathin nanowires, of particular interest is the laser ablation of metal-containing solid targets or similar techniques [7–10], by which bulk-quantity nanowires can be readily obtained directly from solid source materials. When using metal catalysts, for example, for the synthesis of Si nanowires, this method is suggested to rely on the VLS mechanism, whereby the vapor (or gaseous clusters) generated by laser ablation dissolves in a molten metal catalyst and then crystallizes to form nanowires. Ultrasmall nanoparticles of metals or metal silicides in large quantities are rather easy to obtain from the high temperature induced by laser ablation. Assisted by laser ablation, these nanoparticles act as the critical catalyst for the nucleation and growth of nanowires. The laser-assisted method has unique advantages over other growth techniques in synthesizing nanowires containing complex chemical compositions. This is because no matter how many elements are involved, it is not necessary to prepare the target (or the source materials) in a crystalline form. A simple mixture of the elements is good enough as the source material. The source materials are ablated into a vapor phase, which may have the same composition as the source materials. The vapor phase can be easily transferred to the substrate where nanowires nucleate and grow. A high-energy laser can ablate solid materials in an ultra short time and vaporize the materials in a non-thermoequilibrium process, also called congruent evaporation [55]. This technique is particularly useful in the synthesis of nanowires with a high-melting temperature, such as SiC nanowires[56]. It is also a very effective method in synthesizing nanowires with multicomponents and doping nanowires during growth. The vaporized molecules (or clusters) by the high power laser have high kinetic energy (about 100 eV), and this largely enhances the chemical reaction, e.g., the reaction with oxygen or other gases, and thus can largely improve the crystal quality of the nanowires at a low substrate temperature. This special technique has many practical uses for the control of the stoichiometries of nanowires. For example, ZnO nanowires grown by thermal CVD always have oxygen vacancies and other defects that cause poor optical (nonband edge emission) and electrical (low conductivity compared with bulk ZnO crystals) properties. These defects cannot be easily eliminated even by annealing in oxygen after nanowire growth. ZnO nanowires synthesized by laser ablation, however, generally show better optical properties. Another example is that indium oxide nanowires synthesized by laser ablation have a significantly high mobility [57]. Fig. 4 is a schematic of the experimental setup of the laserablation technique. The laser used in the experiment can be any high-power pulsed laser, e.g., a Nd:YAG laser [7], an interfered femto-second laser[58] or an excimer laser[59]. The synthesis of Si nanowires by the experiment reported in Refs. [10,59,60] was carried out using a high-power KrF excimer pulsed laser (248 nm, 10 Hz, 400 mJ/pulse) to ablate a target in an evacuated (500 Torr) quartz tube with Ar (50 sccm) flowing through the tube. Other inert gases, such as He, H2 and N2, can also be used as the ambient gases. The use of different ambient gases may influence the diameters of the nanowires and affects their optical properties [60]. The temperature around the target materials in the experiment was about 1200 8C. The target was highly pure Si powder mixed with Fe, Ni, or Co (about 0.5%). The laser beam (1 mm 3 mm) was focused on the target surface. Si nanowire products (sponge-like, dark yellow in color as shown in Fig. 5(a)) formed on the Si substrate or the inner wall of the quartz tube near the water-cooled finger after 1 h of laser ablation. The temperature of the area around the substrate where the nanowire grew was approximately 900–1000 8C. The growth rate of the Si nanowires was about 10–80 mm/h. By laser ablation, the metal powder is evaporated out of the target to form clusters. They are in a semi-liquid state and serve Fig. 4. Experimental setup for the synthesis of Si nanowires by laser ablation (Courtesy of Prof. I. Bello). N. Wang et al. / Materials Science and Engineering R 60 (2008) 1–51 5
N. Wang et al/Materials Science and Engineering R 60(2008)1-51 O-Kvy vire product. (b) Formation of Si nanowires from liquid clusters. (c) TEM image of Si nanowires catalyzed by metal droplets. The arrow indicates as the energetically favored reaction sites for absorption of the YBCO nanowires were structurally uniform. Their diameters reactant. They are also the nucleation sites for crystallization of range from 20 and 90 nm and their lengths are up to several the source materials when supersaturated(see Fig. 5(b). Then, micrometers. Most of the YBCO nanowires were single crystals preferential ID growth occurs in the presence of the reactant Si (an orthorhombic lattice)and their axis was along the [001 nanowires obtained by ablating a metal-containing(0.5-1%)Si direction. The growth mechanism of the YBCO nanowires is powder target are extremely long and straight. The typical not known. It might be a self-catalytic growth or the oxide- diameters of the nanowires are 10-50 nm. There is a metal assisted growth (without any metal catalysts) as discussed catalyst at the tip of each nanowire(Fig. 5(c)). During the laser below in Section 2.3 blation, the reaction is not under thermodynamic equilibrium onditions. Ultrasmall-size metal catalysts and thus very thin Si 2.3. Thermal evaporation nanowires with diameters smaller than 10 nm can be easily generated by this method. The growth rate of Si nanowires from Nanowires and some interesting morphologies of nanos- ser ablation depends on many factors, such as the power of the tructures such as nanoribbons, nano-tetrapods and comb-like laser beam, the vacuum, the carrier gasses and the temperature. structures [64, 65] can be fabricated by a simple method of A rate of 500 um/h has been observed in Si nanowire growth thermal evaporation of solid source materials. The exper assisted by laser ablation, which is much faster than that from mental setup is extremely simple as shown in Fig. 6. The the classical VLS using vapor sources temperature gradient and the vacuum conditions are two critical without adding any metal catalysts, however, nanowires parameters for the formation of nanowires by this method many other materials have been fabricated by laser ablation. Typical materials suitable for this fabrication are metal oxides, These materials include metal oxides, some semiconductors e.g, ZnO, SnO2, In2O3, VO, etc and some semiconductors and multi-component materials with rather complex stoichio- [12, 66]. The fabrication of these nanowires is simply through metries.The growth of these nanowires is called self-catalyzed evaporating commercial metal oxide powders at elevated rowth. Though no obvious catalyst is observed with these temperatures under a vacuum or in an inert gas atmosphere with nanowires, it is possible that metal elements in the source a negative pressure. Nanowire products form in the low materials may act as the catalysts. For example, the laser temperature regions where materials deposit from the vapor ablation of the ZnSe crystal surface may result in Zn clusters phase. It is believed that the nanowires are generated directly that act as the effective catalysts. Similar self-catalyst VLs from the vapor phase in the absence of a metal catalyst, and this growth has also been observed in the growth of Gan [61] and process is often called vapor-solid(VS)growth. To generate ZnO [62] nanowires. Nanowires with multi-components, for the vapor phases of the source materials, vacuum conditions are example, the yttrium-barium-copper-oxygen (YBCO)com- sometimes needed. This is because some materials may not pound, have been synthesized by laser ablation of YBa2Cu3O7 sublimate in the normal atmosphere. An effective way to (a high T-c superconductor) in an oxygen atmosphere [63]. The generate the vapor source materials in a normal atmosphere is Pressure meter A dual temperature zone furnace Nanowires Carrier gas T 600°c Seal ring I Temperature Zone Al I Temperature Zone Bl Quartz tube Fig. 6. A simple experimental setup of the thermal evaporation method for synthesizing ZnO nanostructures. The source material is Zno or a mixture of ZnO and carbon. Different forms of the Zno nanostructures, e. g, nanowires and ribbons, grow in different temperature zones
as the energetically favored reaction sites for absorption of the reactant. They are also the nucleation sites for crystallization of the source materials when supersaturated (see Fig. 5(b)). Then, preferential 1D growth occurs in the presence of the reactant. Si nanowires obtained by ablating a metal-containing (0.5–1%) Si powder target are extremely long and straight. The typical diameters of the nanowires are 10–50 nm. There is a metal catalyst at the tip of each nanowire (Fig. 5(c)). During the laser ablation, the reaction is not under thermodynamic equilibrium conditions. Ultrasmall-size metal catalysts and thus very thin Si nanowires with diameters smaller than 10 nm can be easily generated by this method. The growth rate of Si nanowires from laser ablation depends on many factors, such as the power of the laser beam, the vacuum, the carrier gasses and the temperature. A rate of 500 mm/h has been observed in Si nanowire growth assisted by laser ablation, which is much faster than that from the classical VLS using vapor sources. Without adding any metal catalysts, however, nanowires of many other materials have been fabricated by laser ablation. These materials include metal oxides, some semiconductors and multi-component materials with rather complex stoichiometries. The growth of these nanowires is called self-catalyzed growth. Though no obvious catalyst is observed with these nanowires, it is possible that metal elements in the source materials may act as the catalysts. For example, the laser ablation of the ZnSe crystal surface may result in Zn clusters that act as the effective catalysts. Similar self-catalyst VLS growth has also been observed in the growth of GaN [61] and ZnO [62] nanowires. Nanowires with multi-components, for example, the yttrium–barium–copper–oxygen (YBCO) compound, have been synthesized by laser ablation of YBa2Cu3O7 (a high T-c superconductor) in an oxygen atmosphere [63]. The YBCO nanowires were structurally uniform. Their diameters range from 20 and 90 nm and their lengths are up to several micrometers. Most of the YBCO nanowires were single crystals (an orthorhombic lattice) and their axis was along the [0 0 1] direction. The growth mechanism of the YBCO nanowires is not known. It might be a self-catalytic growth or the oxideassisted growth (without any metal catalysts) as discussed below in Section 2.3. 2.3. Thermal evaporation Nanowires and some interesting morphologies of nanostructures such as nanoribbons, nano-tetrapods and comb-like structures [64,65] can be fabricated by a simple method of thermal evaporation of solid source materials. The experimental setup is extremely simple as shown in Fig. 6. The temperature gradient and the vacuum conditions are two critical parameters for the formation of nanowires by this method. Typical materials suitable for this fabrication are metal oxides, e.g., ZnO, SnO2, In2O3, VO, etc. and some semiconductors [12,66]. The fabrication of these nanowires is simply through evaporating commercial metal oxide powders at elevated temperatures under a vacuum or in an inert gas atmosphere with a negative pressure. Nanowire products form in the lowtemperature regions where materials deposit from the vapor phase. It is believed that the nanowires are generated directly from the vapor phase in the absence of a metal catalyst, and this process is often called vapor–solid (VS) growth. To generate the vapor phases of the source materials, vacuum conditions are sometimes needed. This is because some materials may not sublimate in the normal atmosphere. An effective way to generate the vapor source materials in a normal atmosphere is Fig. 5. (a) Si nanowire product. (b) Formation of Si nanowires from liquid clusters. (c) TEM image of Si nanowires catalyzed by metal droplets. The arrow indicates the metal catalyst on the nanowire tip. Fig. 6. A simple experimental setup of the thermal evaporation method for synthesizing ZnO nanostructures. The source material is ZnO or a mixture of ZnO and carbon. Different forms of the ZnO nanostructures, e.g., nanowires and ribbons, grow in different temperature zones. 6 N. Wang et al. / Materials Science and Engineering R 60 (2008) 1–51
N. Wang et al. /Materials Science and Engineering R 60 (2008)1-51 to add additional materials to react with the source materials. temperature was about 800-1000C. A similar thermal For example, Zno powder does not sublimate in a normal evaporation experiment was actually performed in 1950 atmosphere at 1000C. By adding carbon powder to react with [55,75]. Two kinds of materials were obtained at the the ZnO source, Zn or Zn-suboxide vapor phases can be easily temperature range of 800-1000C, one was a Sio product generated at 1000C. Various forms of ZnO nanostructures and the other one was labeled as"light brown loose material ow in the low-temperature zone. In this case, vacuum The loose materials were characterized by X-ray diffraction and conditions, carrying gases and catalysts are all unnecessary. determined to be Si structures [75]. The"light brown loose The temperature is critical for the formation of different forms material"can be obtained routinely nowadays by thermal of ZnO nanostructures [67]. evaporation as Si nanowires. Unfortunately, the Si nanowires in The growth mechanisms of many nanowires from thermal the loose materials were not identified at the time of the initial evaporation (without adding metal catalysts) are poorly experiments. The advantages of the OAG technique are(1)the understood. There are some special materials containing no nanowires are highly pure since no metal catalyst is involved metal elements that can also develop into nanowires from their and (2)doping of nanowires can be easily achieved because the oxide decomposition. Wang et al. [11, 68, 69]reported that SiO2 experimental setup for OAG of Si nanowires is very similar to largely enhanced Si nanowire growth(Fig. 7(a). A model that of the laser ablation technique. Doping can be easily called oxide-assisted growth(OAG) was therefore proposed realized with the assistance of laser ablation of solid dopant with evidence from experiments not only on Si but also on Ge materials during nanowire growth. Si nanowires fabricated by [70]and Ill-V[71-73] semiconductor nanowire growth. As this method showed very uniform diameters(about 20 nm)and shown in Fig. 7(b), the presence of Sio2 in the source their lengths were over several hundred micrometers significantly increases the yield of Si nanowire product. The Si nanowire product obtained using a powder source composed of 2. 4. Metal-catalyzed molecular-beam epitaxy 50%0 SiO, and 50%o Si is 30 times larger than the amount generated by using a metal-containing target [11] Since 2000, MBE and CBe techniques have been employed The OAG reaction is special because no metal elements or to synthesize Si [15], Il-VI[14] and Ill-V[13, 16] compound catalysts are involved either in the source materials or the semiconductor nanowires based on the Vls growth mechan- nanowire itself. The starting material is oxide and the ism MBE and CBe techniques provide an ideal clean growth nanowires are in non-oxide form. In OAG using Sio, the environment, and the atomic structures, doping states and nanowires are pure Si(not Si-oxide), and Si itself does not have junctions (or heterostructures) can be well controlled. a self-catalyst effect. This means that Si nanowires are formed Combined with the VLS, these techniques are able to produce by the assistance of Si-oxide. The OAG model has been tested high-quality semiconductor nanowires. Different from other by a simple experiment [74], which was carried out by simply synthesis techniques, MBE works under ultra-high vacuum sealing highly pure Sio powder or a mixture of Si and Sio2 conditions. The mean free path of the source molecules under (: 1, Si reacts with SiO2 to form Sio or Si,o(x> 1) vapor vacuum conditions of 10 Torr is about 0. 2 m The evaporated phase)in an evacuated(vacuum <10 Torr)quartz tube and then source atoms or molecules from the effusion cells behave like a inserting the tube into a preheated furnace(1250-1300C). No beam aiming directly at the substrate(see Fig. 8). The growth, special ambient gas was needed. One end of the tube was left surface structures and contamination can be monitored in situ outside the furnace to generate a temperature gradient between by reflection high-energy electron diffraction, Auger electron the source material and the nanowire formation zone. After 20- spectroscopy and other surface probing techniques. MBE has 30 min of annealing, a high yield of sponge-like Si nanowire several advantages over other synthesis techniques: (1)the product formed on the cooler parts of the tube where the ultra-high vacuum can reduce contamination/oxidation of (b) ooE卫9 300nm SiO2(wt%) Fig. 7.(a)Si nanowires synthesized by oxide-assisted growth. (b)Yield of Si nanowires vs the percentage of Sioz in the target [ll
to add additional materials to react with the source materials. For example, ZnO powder does not sublimate in a normal atmosphere at 1000 8C. By adding carbon powder to react with the ZnO source, Zn or Zn-suboxide vapor phases can be easily generated at 1000 8C. Various forms of ZnO nanostructures grow in the low-temperature zone. In this case, vacuum conditions, carrying gases and catalysts are all unnecessary. The temperature is critical for the formation of different forms of ZnO nanostructures [67]. The growth mechanisms of many nanowires from thermal evaporation (without adding metal catalysts) are poorly understood. There are some special materials containing no metal elements that can also develop into nanowires from their oxide decomposition. Wang et al. [11,68,69] reported that SiO2 largely enhanced Si nanowire growth (Fig. 7(a)). A model called oxide-assisted growth (OAG) was therefore proposed with evidence from experiments not only on Si but also on Ge [70] and III–V [71–73] semiconductor nanowire growth. As shown in Fig. 7(b), the presence of SiO2 in the source significantly increases the yield of Si nanowire product. The Si nanowire product obtained using a powder source composed of 50% SiO2 and 50% Si is 30 times larger than the amount generated by using a metal-containing target [11]. The OAG reaction is special because no metal elements or catalysts are involved either in the source materials or the nanowire itself. The starting material is oxide and the nanowires are in non-oxide form. In OAG using SiO, the nanowires are pure Si (not Si-oxide), and Si itself does not have a self-catalyst effect. This means that Si nanowires are formed by the assistance of Si-oxide. The OAG model has been tested by a simple experiment [74], which was carried out by simply sealing highly pure SiO powder or a mixture of Si and SiO2 (1:1, Si reacts with SiO2 to form SiO or SixO (x > 1) vapor phase) in an evacuated (vacuum <10 Torr) quartz tube and then inserting the tube into a preheated furnace (1250–1300 8C). No special ambient gas was needed. One end of the tube was left outside the furnace to generate a temperature gradient between the source material and the nanowire formation zone. After 20– 30 min of annealing, a high yield of sponge-like Si nanowire product formed on the cooler parts of the tube where the temperature was about 800–1000 8C. A similar thermal evaporation experiment was actually performed in 1950 [55,75]. Two kinds of materials were obtained at the temperature range of 800–1000 8C, one was a SiO product and the other one was labeled as ‘‘light brown loose material’’. The loose materials were characterized by X-ray diffraction and determined to be Si structures [75]. The ‘‘light brown loose material’’ can be obtained routinely nowadays by thermal evaporation as Si nanowires. Unfortunately, the Si nanowires in the loose materials were not identified at the time of the initial experiments. The advantages of the OAG technique are (1) the nanowires are highly pure since no metal catalyst is involved and (2) doping of nanowires can be easily achieved because the experimental setup for OAG of Si nanowires is very similar to that of the laser ablation technique. Doping can be easily realized with the assistance of laser ablation of solid dopant materials during nanowire growth. Si nanowires fabricated by this method showed very uniform diameters (about 20 nm) and their lengths were over several hundred micrometers. 2.4. Metal-catalyzed molecular-beam epitaxy Since 2000, MBE and CBE techniques have been employed to synthesize Si [15], II–VI [14] and III–V [13,16] compound semiconductor nanowires based on the VLS growth mechanism. MBE and CBE techniques provide an ideal clean growth environment, and the atomic structures, doping states and junctions (or heterostructures) can be well controlled. Combined with the VLS, these techniques are able to produce high-quality semiconductor nanowires. Different from other synthesis techniques, MBE works under ultra-high vacuum conditions. The mean free path of the source molecules under vacuum conditions of 105 Torr is about 0.2 m. The evaporated source atoms or molecules from the effusion cells behave like a beam aiming directly at the substrate (see Fig. 8). The growth, surface structures and contamination can be monitored in situ by reflection high-energy electron diffraction, Auger electron spectroscopy and other surface probing techniques. MBE has several advantages over other synthesis techniques: (1) the ultra-high vacuum can reduce contamination/oxidation of Fig. 7. (a) Si nanowires synthesized by oxide-assisted growth. (b)Yield of Si nanowires vs. the percentage of SiO2 in the target [11]. N. Wang et al. / Materials Science and Engineering R 60 (2008) 1–51 7
N. Wang et al/Materials Science and Engineering R 60(2008)1-51 Electron Effusion Molecular RHEED Fig 8. A typical MBE growth chamber. material surfaces; (2)the low growth temperature and the temperature. In practice, Au nanoparticles are not necessarily growth rate prevent inter-diffusion in the nanostructures; (3)in molten droplets. In fact, the nanowires can grow at a situ monitoring of growth is possible; (4) since all growth temperature below the eutectic point. However, the deposition parameters can be adjusted precisely and separately, the of the source atoms on the substrate surface becomes significant intrinsic nanowire growth phenomena can be studied indivi- at a low temperature. Then, the surface diffusion becomes an dually. essential mechanism. Excess adatoms are driven to the low For a classical VLS reaction, the metal particles are essential energy state of the molten metallic particles or the molten for the catalytic decomposition of the precursors. For MBe interfaces at these particles growth, however, no molecules or precursors need to The growth temperature is a critical factor for the formation decompose. The function of the metal particles is twofold: of high-quality ZnSe nanowires. On the one hand, the (1)absorption of atoms from vapor phases or substrate surfaces. deposition of ZnSe on the substrate is restrained when the The driving force is to lower the chemical potentials of the substrate temperature is substantially higher than 300C. source atoms and(2)precipitation or crystallization of the Therefore, almost no ZnSe deposition occurs on the fresh e particle-substrate interface. The surface of the substrate(see Fig. 9(a)). On the other hand, a preparation of the substrate surface is critical for growing certain high temperature is needed in order to activate the Au- high-quality nanowires. After wet-chemical cleaning, the alloy particles on the substrate and to"catalyze"the growth of substrate has to be deoxidized. Substrate de-oxidation is the ZnSe nanowires epitaxially on the substrate. Due to the essential because the oxide layer on the substrate influences the surface melting effect, it is possible to grow ZnSe nanowires at nanowire growth direction. A poorly treated substrate results in a low temperature of about 390C. In this case, the deposition random growth directions. The deoxidation temperature of ZnSe on the substrate surface is significant(Fig 9(b)), and depends on the substrates used. For a GaP(111)substrate, the quality of the nanowires is poor compared with the quality for example, annealing at 600C is essential. For the growth of of nanowires grown at a higher temperature. These nanowires II-VI(e.g, ZnSe and ZnS) nanowires [14, the synthesis is contain high-density defects, e.g., stacking faults and twin- carried out using compound-source effusion cells at tempera- nings. However, a too-high growth temperature results in tures above 500C. According to in situ observations of the coarsening of the Au catalyst and a low growth rate and, in turn, reflection high-energy electron diffraction patterns during the leads to non-uniform diameters of the ZnSe nanowires. The growth, Au nanoparticles are in a molten state at this resulting growth rate of the nanowires is mainly determined by Fig 9. TEM images of the interface structures at the substrate. (a) No deposition of the source materials on the substrate surface under a high growth temperature. (b) Deposition of the source materials on the substrate surface under a low growth temperature
material surfaces; (2) the low growth temperature and the growth rate prevent inter-diffusion in the nanostructures; (3) in situ monitoring of growth is possible; (4) since all growth parameters can be adjusted precisely and separately, the intrinsic nanowire growth phenomena can be studied individually. For a classical VLS reaction, the metal particles are essential for the catalytic decomposition of the precursors. For MBE growth, however, no molecules or precursors need to decompose. The function of the metal particles is twofold: (1) absorption of atoms from vapor phases or substrate surfaces. The driving force is to lower the chemical potentials of the source atoms and (2) precipitation or crystallization of the source materials at the particle-substrate interface. The preparation of the substrate surface is critical for growing high-quality nanowires. After wet-chemical cleaning, the substrate has to be deoxidized. Substrate de-oxidation is essential because the oxide layer on the substrate influences the nanowire growth direction. A poorly treated substrate results in random growth directions. The deoxidation temperature depends on the substrates used. For a GaP(1 1 1) substrate, for example, annealing at 600 8C is essential. For the growth of II–VI (e.g., ZnSe and ZnS) nanowires [14], the synthesis is carried out using compound-source effusion cells at temperatures above 500 8C. According to in situ observations of the reflection high-energy electron diffraction patterns during the growth, Au nanoparticles are in a molten state at this temperature. In practice, Au nanoparticles are not necessarily molten droplets. In fact, the nanowires can grow at a temperature below the eutectic point. However, the deposition of the source atoms on the substrate surface becomes significant at a low temperature. Then, the surface diffusion becomes an essential mechanism. Excess adatoms are driven to the low energy state of the molten metallic particles or the molten interfaces at these particles. The growth temperature is a critical factor for the formation of high-quality ZnSe nanowires. On the one hand, the deposition of ZnSe on the substrate is restrained when the substrate temperature is substantially higher than 300 8C. Therefore, almost no ZnSe deposition occurs on the fresh surface of the substrate (see Fig. 9(a)). On the other hand, a certain high temperature is needed in order to activate the Aualloy particles on the substrate and to ‘‘catalyze’’ the growth of the ZnSe nanowires epitaxially on the substrate. Due to the surface melting effect, it is possible to grow ZnSe nanowires at a low temperature of about 390 8C. In this case, the deposition of ZnSe on the substrate surface is significant (Fig. 9(b)), and the quality of the nanowires is poor compared with the quality of nanowires grown at a higher temperature. These nanowires contain high-density defects, e.g., stacking faults and twinnings. However, a too-high growth temperature results in coarsening of the Au catalyst and a low growth rate and, in turn, leads to non-uniform diameters of the ZnSe nanowires. The resulting growth rate of the nanowires is mainly determined by Fig. 8. A typical MBE growth chamber. Fig. 9. TEM images of the interface structures at the substrate. (a) No deposition of the source materials on the substrate surface under a high growth temperature. (b) Deposition of the source materials on the substrate surface under a low growth temperature. 8 N. Wang et al. / Materials Science and Engineering R 60 (2008) 1–51
N. Wang et al. /Materials Science and Engineering R 60 (2008)1-51 the ZnSe flux at a fixed temperature. At 530C, the growth rate as surfactants and organic dopants and (2)"hard templates, of ZnSe nanowires is about 0. 1 nm/s [14) such as anodized alumina membranes [95-103] containing CBE is a hybrid form of molecular beam epitaxy. Different nanosized channels, track-etched polymer porous membranes, tures), gas sources are used(also called gas source molecules. and some special crystals containing nanochannels. Through MBE (using solid so r DC or AC electrochemical deposition, various materials can be beam epitaxy) CBE works at an ultrahigh vacuum condition so introduced into the nanochannels of the hard template [100- that the mean-free paths between molecular collisions become 103. In some cases, vapor molecules may selectively diffuse longer than the source inlet and the substrate. The gaseous into the channels because of special chemical properties of the ource materials are introduced(the gas transport is collision nanochannel walls [103]. without the assistance of structural free)into the reaction chamber at room temperature in the form directors, anisotropic growth of crystals induced by different of a beam. From Au-catalyzed CBe, high-quality ID surface energies can lead to the formation of elongated heterostructure nanowires(InAs/InP) with diameters of about nanocrystals. However, the differences in the surface energies 40 nm have been fabricated [16]. Very thin Inp barrier layers of most materials are not large enough to cause highly with thicknesses of 1. 5 nm and excellent interface structures anisotropic growth of long nanowires By adding surfactants to have been demonstrated by this method. The growth direction the reaction solution, some surfaces of nanocrystals can be and defect density in the nanowires grown by CBE and MBe modulated, i.e., the surfactant molecules selectively adsorb and are influenced by several factors. Twinning(see Fig 9(a)) or bind onto certain surfaces of the nanocrystals and thus reduce stacking faults are the main defects that very often occur in the growth of these surfaces. This selective capping effect thicker nanowires and cause a change of the nanowire growth induces the nanocrystal elongation along a specific direction to direction. For ZnSe nanowire growth, the growth temperature form nanowires. The selective capping mechanism has been and the ratio of the source elements are the main reasons evidenced recently in many nanomaterials such as metal causing the defects. The defect density is also dependent on the nanowires[104-109), metal oxide nanowires [110-115] and growth direction. We have observed that [00 1] growth semiconductor nanowires [116, 117. Though structural direc- nanowires contain fewer defects compared with nanowires tors are often used for the synthesis of nanowires, the actual grown in other directions, and ultra-thin nanowires(diame- growth process is poorly known. As a matter of fact, in many ter< 10 nm) generally contain few defects. The growth cases, the structural directors may not exist or the materials are directions of ultra-thin II-VI compound nanowires are mainly self-constitutive templates. The formation mechanism of determined by the diameters or the sizes of the catalysts and the nanowires in solution is complicated and the selection and growth temperature. The size-dependent and temperature- function of the structural directors require further dependent growth directions and the interface structures of l- systematic investigation Vi nanowires are discussed in Section 4.1 based on the estimation of the surface and interface energies of the nanowire 3. growth mechanisms of nanowires nuclei 3.1. Metal-catalyzed growth 25. Solution methods The most significant work on the mechanism of the The major advantages of the solution-based technique (in unidirectional growth of semiconductor whiskers grown by aqueous or non-hydrolytic media) for synthesizing nanomater- VLS was published by Wagner and Ellis in 1965 [118]. The als are high yield, low cost and easy fabrication. The solution- unidirectional growth of Si whiskers can be simply interpreted based technique has been demonstrated as a promising based on the difference of the sticking coefficients of the alternative approach for mass production of metal, semicon- impinging vapor source atoms on the liquid(the catalytic ductor and oxide nanomaterials with excellent controls of the droplet)and on solid surfaces. In principle, an ideal liquid shape and composition with high reproducibility. In particular, surface captures all impinging Si source atoms, while a solid this technique is able to assemble nanocrystals with other surface of Si rejects almost all Si source atoms if the functional materials to form hybrid nanostructures with multiple temperature is sufficiently high. This classical VLS mechanism functions with great potential for applications in nanoelectronic is still applicable to the growth of many nanoscale wires and biological systems. The nanocrystals synthesized in aqueous produced today. As schematically shown in Fig. 10(a),Au media may often suffer from poor crystallinity, but those particles deposited on the surface of an Si substrate initially ture, in general, show much better crystal quality(76,77). For the temperature of a Si-Au alloy particle is significantly decreang synthesized under nonhydrolytic conditions at a high tempera- react with Si to form active Au-Si alloy droplets. The melting formation of nanowires from solution, several routes have been once its size is in the nanometer range [119]. during the initial developed, such as metal-catalyzed solution-liquid-solid(sLs) reaction of the catalyst on a flat surface(see also Fig. 10(b)), the growth from metal seeds [78-88], self-assembly attachment shape or the contact angle (P)of the droplet is determined by growth [89-94], and anisotropic growth of crystals by the balanced forces of the surface tension and the liquid-solid thermodynamic or kinetic control (LS)interface tension. The droplet has a radius, R, which can be Many nanowires grown from solution methods largely rely described by R=o/sin(Bo)(ro is the radius of the contact area) on"structural directors", including(1)"soft templates, such [ 120, 121]. The contact angle is related to the surface tension
the ZnSe flux at a fixed temperature. At 530 8C, the growth rate of ZnSe nanowires is about 0.1 nm/s [14]. CBE is a hybrid form of molecular beam epitaxy. Different from MBE (using solid sources evaporated at high temperatures), gas sources are used (also called gas source molecular beam epitaxy). CBE works at an ultrahigh vacuum condition so that the mean-free paths between molecular collisions become longer than the source inlet and the substrate. The gaseous source materials are introduced (the gas transport is collision free) into the reaction chamber at room temperature in the form of a beam. From Au-catalyzed CBE, high-quality 1D heterostructure nanowires (InAs/InP) with diameters of about 40 nm have been fabricated [16]. Very thin InP barrier layers with thicknesses of 1.5 nm and excellent interface structures have been demonstrated by this method. The growth direction and defect density in the nanowires grown by CBE and MBE are influenced by several factors. Twinning (see Fig. 9(a)) or stacking faults are the main defects that very often occur in thicker nanowires and cause a change of the nanowire growth direction. For ZnSe nanowire growth, the growth temperature and the ratio of the source elements are the main reasons causing the defects. The defect density is also dependent on the growth direction. We have observed that [0 0 1] growth nanowires contain fewer defects compared with nanowires grown in other directions, and ultra-thin nanowires (diameter < 10 nm) generally contain few defects. The growth directions of ultra-thin II–VI compound nanowires are mainly determined by the diameters or the sizes of the catalysts and the growth temperature. The size-dependent and temperaturedependent growth directions and the interface structures of II– VI nanowires are discussed in Section 4.1 based on the estimation of the surface and interface energies of the nanowire nuclei. 2.5. Solution methods The major advantages of the solution-based technique (in aqueous or non-hydrolytic media) for synthesizing nanomaterials are high yield, low cost and easy fabrication. The solutionbased technique has been demonstrated as a promising alternative approach for mass production of metal, semiconductor and oxide nanomaterials with excellent controls of the shape and composition with high reproducibility. In particular, this technique is able to assemble nanocrystals with other functional materials to form hybrid nanostructures with multiple functions with great potential for applications in nanoelectronic and biological systems. The nanocrystals synthesized in aqueous media may often suffer from poor crystallinity, but those synthesized under nonhydrolytic conditions at a high temperature, in general, show much better crystal quality [76,77]. For the formation of nanowires from solution, several routes have been developed, such as metal-catalyzed solution-liquid-solid (SLS) growth from metal seeds [78–88], self-assembly attachment growth [89–94], and anisotropic growth of crystals by thermodynamic or kinetic control. Many nanowires grown from solution methods largely rely on ‘‘structural directors’’, including (1) ‘‘soft templates,’’ such as surfactants and organic dopants and (2) ‘‘hard templates,’’ such as anodized alumina membranes [95–103] containing nanosized channels, track-etched polymer porous membranes, and some special crystals containing nanochannels. Through DC or AC electrochemical deposition, various materials can be introduced into the nanochannels of the hard template [100– 103]. In some cases, vapor molecules may selectively diffuse into the channels because of special chemical properties of the nanochannel walls [103]. Without the assistance of structural directors, anisotropic growth of crystals induced by different surface energies can lead to the formation of elongated nanocrystals. However, the differences in the surface energies of most materials are not large enough to cause highly anisotropic growth of long nanowires. By adding surfactants to the reaction solution, some surfaces of nanocrystals can be modulated, i.e., the surfactant molecules selectively adsorb and bind onto certain surfaces of the nanocrystals and thus reduce the growth of these surfaces. This selective capping effect induces the nanocrystal elongation along a specific direction to form nanowires. The selective capping mechanism has been evidenced recently in many nanomaterials such as metal nanowires [104–109], metal oxide nanowires [110–115] and semiconductor nanowires [116,117]. Though structural directors are often used for the synthesis of nanowires, the actual growth process is poorly known. As a matter of fact, in many cases, the structural directors may not exist or the materials are self-constitutive templates. The formation mechanism of nanowires in solution is complicated and the selection and function of the structural directors require further and systematic investigation. 3. Growth mechanisms of nanowires 3.1. Metal-catalyzed growth The most significant work on the mechanism of the unidirectional growth of semiconductor whiskers grown by VLS was published by Wagner and Ellis in 1965 [118]. The unidirectional growth of Si whiskers can be simply interpreted based on the difference of the sticking coefficients of the impinging vapor source atoms on the liquid (the catalytic droplet) and on solid surfaces. In principle, an ideal liquid surface captures all impinging Si source atoms, while a solid surface of Si rejects almost all Si source atoms if the temperature is sufficiently high. This classical VLS mechanism is still applicable to the growth of many nanoscale wires produced today. As schematically shown in Fig. 10(a), Au particles deposited on the surface of an Si substrate initially react with Si to form active Au–Si alloy droplets. The melting temperature of a Si–Au alloy particle is significantly decreased once its size is in the nanometer range [119]. During the initial reaction of the catalyst on a flat surface (see also Fig. 10(b)), the shape or the contact angle (bo) of the droplet is determined by the balanced forces of the surface tension and the liquid–solid (LS) interface tension. The droplet has a radius, R, which can be described by R=r0/sin(b0) (r0 is the radius of the contact area) [120,121]. The contact angle is related to the surface tension N. Wang et al. / Materials Science and Engineering R 60 (2008) 1–51 9
N. Wang et al/Materials Science and Engineering R 60(2008)1-51 Vapor phases Si+M Liquid (Si+M OLs o Fig. 10. Schematic of Au-Si droplets(a) formed on the substrate (b)Initial growth of the nanowire. (c) The hillock shape of the nanowire root(from Ref. [121] courtesy of Prof. T Y. Tan and the line tension, t, by a modified(a line tension is added) Gibbs free energy, Li et al. obtained [120, 121]: Youngs equation [122] OVL COS Bo=OVS --OLS (3.1.3) O1 cos( Bo)=os-OIs (3.1.1 For a droplet of macroscopic size, the effect of the line tension LSo 221, can be ignored. For a nanosized droplet, the line tension should where ois is the effective surface tension, t' the effective be considered. At the initial growth, when the nanowire's chemical tension, Io the elementary thickness and n is the vapor length, dh, increases, the radius of the contact area. source of the actual-to-equilibrium-pressure ratio. The cher decreases. The inclination angle, a, of the nanowire flanks will cal tensional is defined as: o=ois +(r/r). Then, the increase(a=0 before growth). The inclination angle can be general equation for a wire already grown to some length is OVL COS Bo=Ovs -OLS -o. The equilibrium condition of the VlS reaction is the balance among the various static factors in a1 cos(B)=Os cos(ax)-a1 (3.1.2) the system, the surface energies, the dynamic factors due to the growth of a crystal layer, and the chemical tension. The shape of An increase in a is accompanied by an increase in B. The an initially grown Si nanowire(due to the line-tension)is shown droplet will approach a spherical section. Since the contact area in the TEM image in Fig. 11(a). Based on the chemical-tension decreases with an increase in the nanowire length, the final model, Li et al. predicted that different line-tension values can radius of the nanowire should be smaller than the initial radius, result in nanowire or nanohillock growth as shown in Fig. 11(b) 10(c)). The line tension ult to determine For Si whisker growth, a typical kinetic experimental result experimentally)strongly influences the catalyst contact area. a is the growth rate dependence on the whisker diameter. The large line tension can result in hillock growth and thus stop the larger the whisker diameter, the faster is its growth rate growth [120]. Using the minimization method of the systems This growth phenomenon is attributed to the well-known =1.46 T'=0.04 k=0.73 4+℃=008 0.12 r(。) Fig. Il.(a) The shape of the initial growth of Si nanowires due to the line-tension(b) Prediction of Si nanowire and nanohillock growth by the chemical-tension model for various line-tension values(from Ref [ 120]: reproduced with permission from Springer Science)
and the line tension, t, by a modified (a line tension is added) Young’s equation [122]: s1 cosðb0Þ ¼ ss sls t r0 : (3.1.1) For a droplet of macroscopic size, the effect of the line tension can be ignored. For a nanosized droplet, the line tension should be considered. At the initial growth, when the nanowire’s length, dh, increases, the radius of the contact area, dr, decreases. The inclination angle, a, of the nanowire flanks will increase (a = 0 before growth). The inclination angle can be expressed as s1 cosðbÞ ¼ ss cosðaÞ sls t r0 : (3.1.2) An increase in a is accompanied by an increase in b. The droplet will approach a spherical section. Since the contact area decreases with an increase in the nanowire length, the final radius of the nanowire should be smaller than the initial radius, r0 (see Fig. 10(c)). The line tension (difficult to determine experimentally) strongly influences the catalyst contact area. A large line tension can result in hillock growth and thus stop the growth [120].Using the minimization method of the system’s Gibbs free energy, Li et al. obtained [120,121]: sVL cos b0 ¼ sVS sLS sc LS tc ro ; (3.1.3) sc LS ¼ lo kBT V ln h; tc ¼ losVS; (3.1.4) where sc LS is the effective surface tension, tc the effective chemical tension, lo the elementary thickness and h is the vapor source of the actual-to-equilibrium-pressure ratio. The chemical tensional is defined as: sc ¼ sc LS þ ðtc=roÞ. Then, the general equation for a wire already grown to some length is sVL cos b0 = sVS sLS sc . The equilibrium condition of the VLS reaction is the balance among the various static factors in the system, the surface energies, the dynamic factors due to the growth of a crystal layer, and the chemical tension. The shape of an initially grown Si nanowire (due to the line-tension) is shown in the TEM image in Fig. 11(a). Based on the chemical-tension model, Li et al. predicted that different line-tension values can result in nanowire or nanohillock growth as shown in Fig. 11(b). For Si whisker growth, a typical kinetic experimental result is the growth rate dependence on the whisker diameter. The larger the whisker diameter, the faster is its growth rate. This growth phenomenon is attributed to the well-known Fig. 11. (a) The shape of the initial growth of Si nanowires due to the line-tension. (b) Prediction of Si nanowire and nanohillock growth by the chemical-tension model for various line-tension values (from Ref. [120]; reproduced with permission from Springer Science). Fig. 10. Schematic of Au–Si droplets (a) formed on the substrate. (b) Initial growth of the nanowire. (c) The hillock shape of the nanowire root (from Ref. [121]; courtesy of Prof. T.Y. Tan). 10 N. Wang et al. / Materials Science and Engineering R 60 (2008) 1–51