查询 cA158,CA158A,CA258,CA358,CA358A cA2904LM358,LM2904 Data Sheet October 1999 File Number 1019.6 Dual, 1MHz, Operational Amplifiers for Features Commercial Industrial, and Military Applications Internal Frequency Compensation for Unity Gain The CA158 CA158A CA258, CA358 CA358A and CA290 High DC Voltage Gain 100dB (yp) types consist of two independent, high gain, internally Wide Bandwidth at Unity Gain 1MHz (Typ) frequency compensated operational amplifiers which are Wide Power Supply Range designed specifically to operate from a single power supply Single Supply 3V to 30V ver a wide range of voltages. They may also be operated om split power supplies. The supply current is basically 15Vto±15V independent of the supply voltage over the rec Low Supply Current 1.5 mA (Typ) voltage range These devices are particularly useful in interface circuits with digital systems and can be operated from the single Low Input Offset Voltage and Current common 5VDC power supply. They are also intended for cludes Ground transducer amplifiers, dc gain blocks and many other Differential Input Voltage Range Equal to V+ Range conventional op amp circuits which can benefit from the single power supply capability Large Output Voltage Swing oV to V+-1.5V The CA158. CA158A. CA258. CA358. CA358A and Ordering Information CA2904 types are an equivalent to or a replacement for the lustry types 158, 158A, 258, 258A, 358, 358A, and NUMBER RANGE°c) PACKAGE 55 to 125 8 Ld PDIP Technical Data on LM Branded types is identical to the corresponding CA Branded types CAO158AE-55 to 125 8 Ld PDIP CA0158M-55 to 125 8 Ld SOIC M8.15 Pinouts CA0158T to 125 8 Pin Can T8. C CA1 ETAL -25 to 85 8 Ld PDIP E83 25 to 85 8 Ld SOIC M8.15 0 to 70 8 Ld PDIP E8.3 NON-INV INPUT(A)(3 OUTPUT(A) 0 to 708 Ld PDIP E83 CA0358M 0 to 708 Ld SOIC M8.15 PRC -40 to 85 8 Ld PDIP E83 ⑦ OUTPUT(B LM358N 0 to 708 Ld PDIP INPUT (B) LM2904N-40 to 85 8 Ld PDIP E8.3 INPUT (B) cA2904,LM358,LM2904PDP) TOP VIEW INV INPUT(A) T7OUTPUT(B) 5 NON-INV INPUT(B) AUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures 1-888-INTERSIL or 321-724-71431 Copyright Intersil Corporation 1999
1 File Number 1019.6 CA158, CA158A, CA258, CA358, CA358A, CA2904, LM358, LM2904 Dual, 1MHz, Operational Amplifiers for Commercial Industrial, and Military Applications The CA158, CA158A, CA258, CA358, CA358A and CA2904 types consist of two independent, high gain, internally frequency compensated operational amplifiers which are designed specifically to operate from a single power supply over a wide range of voltages. They may also be operated from split power supplies. The supply current is basically independent of the supply voltage over the recommended voltage range. These devices are particularly useful in interface circuits with digital systems and can be operated from the single common 5VDC power supply. They are also intended for transducer amplifiers, DC gain blocks and many other conventional op amp circuits which can benefit from the single power supply capability. The CA158, CA158A, CA258, CA358, CA358A, and CA2904 types are an equivalent to or a replacement for the industry types 158, 158A, 258, 258A, 358, 358A, and CA2904. Technical Data on LM Branded types is identical to the corresponding CA Branded types. Pinouts CA158 (METAL CAN) TOP VIEW CA158, CA258, CA358 (PDIP, SOIC) CA2904, LM358, LM2904 (PDIP) TOP VIEW Features • Internal Frequency Compensation for Unity Gain • High DC Voltage Gain . . . . . . . . . . . . . . . . . . 100dB (Typ) • Wide Bandwidth at Unity Gain . . . . . . . . . . . . .1MHz (Typ) • Wide Power Supply Range: - Single Supply . . . . . . . . . . . . . . . . . . . . . . . . . 3V to 30V • Dual Supplies . . . . . . . . . . . . . . . . . . . . . . . ±1.5V to ±15V • Low Supply Current . . . . . . . . . . . . . . . . . . . .1.5 mA (Typ) • Low Input Bias Current • Low Input Offset Voltage and Current • Input Common-Mode Voltage Range Includes Ground • Differential Input Voltage Range Equal to V+ Range • Large Output Voltage Swing. . . . . . . . . . . . 0V to V+ -1.5V OUTPUT (B) V- V+ INV. INPUT (B) NON-INV. INPUT (B) NON-INV. INPUT (A) INV. INPUT (A) OUTPUT (A) 2 4 6 3 1 5 7 8 A B - - + + 1 2 3 4 8 7 6 5 B A V+ OUTPUT (B) NON-INV. INPUT (B) INV. INPUT (B) V- OUTPUT (A) INV. INPUT (A) NON-INV. INPUT (A) Ordering Information PART NUMBER TEMP. RANGE (oC) PACKAGE PKG. NO. CA0158E -55 to 125 8 Ld PDIP E8.3 CA0158AE -55 to 125 8 Ld PDIP E8.3 CA0158M -55 to 125 8 Ld SOIC M8.15 CA0158T -55 to 125 8 Pin Can T8.C CA0258E -25 to 85 8 Ld PDIP E8.3 CA0258M -25 to 85 8 Ld SOIC M8.15 CA0358E 0 to 70 8 Ld PDIP E8.3 CA0358AE 0 to 70 8 Ld PDIP E8.3 CA0358M 0 to 70 8 Ld SOIC M8.15 CA2904E -40 to 85 8 Ld PDIP E8.3 LM358N 0 to 70 8 Ld PDIP E8.3 LM2904N -40 to 85 8 Ld PDIP E8.3 Data Sheet October 1999 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999 查询CA0158AE供应商
cA158,cA158A,cA258,CA258A,cA358,cA358A,cA2904,LM358,LM2904 Absolute Maximum Ratings Thermal Information Supply Voltage Thermal Resistance(Typical, Note 3) 0JACOCM) OJc(CM) CA2904,LM2904 26or±13v PDIP Package Other Types Differential Input Voltage(All Types Can packa -0.3V to v+ Maximum Junction Temperature(Can Package) Input Current (V1 15V can cause excessive power dissipation and eventual destruction. Short circuits from the output to V+ can cause overheating and eventual destruction of the device. Destructive dissipation can result from simultaneous short circuits on both amplifiers 3. JA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications Values Apply for Each Operational Amplifier. Supply Voltage V+=5V, V-=0 Unless Otherwise Specified CA158A CA358A TEMP PARAMETER TEST CONDITIONS (C)MIN TYPMAX MINTYPMAXUNITS 2 3 Voltage(Note 6) Average Input Offset Voltage Rs=02 15 Input Common Mode Voltage V+=30V v+-1.5 V+-15 5 0 v+-2 v+-2 Common Mode DC Power Supply Rejection Ratio DC Input Bias 4+orIr 20 50 4 Current(Note 4) II+ or lr- 100 Input Offset Current Average Input Offset Current 10300 pA/C Large Signal Voltage Gain RL2 2kQ2, V+= 15V(For 25 50 kVM Large Vo Swing) Output Voltage Swing R1=2k Intersil
2 Absolute Maximum Ratings Thermal Information Supply Voltage CA2904, LM2904 . . . . . . . . . . . . . . . . . . . . . . . . . . . 26V or ±13V Other Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32V or ±16V Differential Input Voltage (All Types) . . . . . . . . . . . . . . . . . . . . . 32V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.3V to V+ Input Current (VI 15V can cause excessive power dissipation and eventual destruction. Short circuits from the output to V+ can cause overheating and eventual destruction of the device. Destructive dissipation can result from simultaneous short circuits on both amplifiers. 3. θJA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications Values Apply for Each Operational Amplifier. Supply Voltage V+ = 5V, V- = 0V, Unless Otherwise Specified PARAMETER TEST CONDITIONS TEMP ( oC) CA158A CA358A MIN TYP MAX MIN TYP MAX UNITS Input Offset Voltage (Note 6) 25 - 1 2 - 2 3 mV Full - - 4 - - 5 mV Average Input Offset Voltage Drift RS = 0Ω Full - 7 15 - 7 20 µV/oC Input Common Mode Voltage Range (Note 5) V+ = 30V 25 0 - V+ -1.5 0 - V+ -1.5 V V+ = 30V Full 0 - V+ -2 0 - V+ -2 V Common Mode Rejection Ratio DC 25 70 85 - 65 85 - dB Power Supply Rejection Ratio DC 25 65 100 - 65 100 - dB Input Bias Current (Note 4) II + or II - 25 - 20 50 - 45 100 nA II+ or II- Full - 40 100 - 40 200 nA Input Offset Current II+ - II- 25 - 2 10 - 5 30 nA II+ - II- Full - - 30 - - 75 nA Average Input Offset Current Drift Full - 10 200 - 10 300 pA/oC Large Signal Voltage Gain RL ≥ 2kΩ, V+ = 15V (For Large VO Swing) 25 50 100 - 25 100 - kV/V Output Voltage Swing RL = 2kΩ 25 0 - V+ -1.5 0 - V+ -1.5 V CA158, CA158A, CA258, CA258A, CA358, CA358A, CA2904, LM358, LM2904
cA158,cA158A,cA258,CA258A,cA358,cA358A,cA2904,LM358,LM2904 Electrical Specifications Values Apply for Each Operational Amplifier. Supply Voltage V+= 5V, V-=0V, Unless otherwise Specified (Continued) CA158A CA358A PARAMETER TEST CONDITIONS °c)MN TYP MAX TYP MAXUNITS Source =+1VV1-=0v.V Current VI+=ov, Vr=1V, 12 Vo= 200mv Short Circuit 60 Output Current(Note 2) Crosstalk Input Referred Total Supply Current 0.7 1.5 NOTES: ue to the PNP input stage the direction of the input current is out of the IC. No loading change exists on the input lines because the current is essentially constant, independent of the state of the output. 5. The input signal voltage and the input common mode voltage should not be allowed to go negative by more than 0. 3v. The positive limit of the is V+-15v, but either or both inputs can go to t 6. Vo =1.4V, Rs 0Q with V+ from 5V to 30v, and over the full input common mode voltage range(ov to V+-15v) Electrical Specifications values Apply for Each Operational Amplifier. Supply Voltage V+= 5V, v-=oV, cA158.cA258 cA358,LM358 cA2904,LM2904 TEST TEMP PARAMETER CONDITIONS (oC)MIN TYP MAX MIN TYP MAX MIN TYP MAXUNITS Voltage(Note 9) Full 7 9 10mV Rs=09 Full v°C rift Input Common Mode V+=30V Voltage Range( Note 8) v+=30V v+-2 Common mode Rejection Ratio Power Supply Rejection D 65100 100 ut Bias II+ or Ir 150 Current(Note 7) Input Offset 4+ 3 30 5 Current 100 45200nA Average Input ent Di I Voltage Full KVN For Large Vo Swing) Output Voltage Swing RL=2kQ ° 15 Intersil
3 Output Current Source VI + = +1V, VI- = 0V, V+ = 15V 25 20 40 - 20 40 - mA Sink VI + = 0V, VI- = 1V, V+ = 15V 25 10 20 - 10 20 - mA VI + = 0V, VI- = 1V, VO = 200mV 25 12 50 - 12 50 - µA Short Circuit Output Current (Note 2) RL = 0Ω 25 - 40 60 - 40 60 mA Crosstalk f = 1 to 20kHz (Input Referred) 25 - -120 - - -120 - dB Total Supply Current RL = ∞ Full - 0.7 1.2 - 0.7 1.2 mA RL = ∞, V+ = 30V Full - 1.5 3 - 1.5 3 mA NOTES: 4. Due to the PNP input stage the direction of the input current is out of the IC. No loading change exists on the input lines because the current is essentially constant, independent of the state of the output. 5. The input signal voltage and the input common mode voltage should not be allowed to go negative by more than 0.3V. The positive limit of the common mode voltage range is V+ - 1.5V, but either or both inputs can go to +32V without damage. 6. VO = 1.4V, RS = 0Ω with V+ from 5V to 30V, and over the full input common mode voltage range (0V to V+ - 1.5V). Electrical Specifications Values Apply for Each Operational Amplifier. Supply Voltage V+ = 5V, V- = 0V, Unless Otherwise Specified (Continued) PARAMETER TEST CONDITIONS TEMP ( oC) CA158A CA358A MIN TYP MAX MIN TYP MAX UNITS Electrical Specifications Values Apply for Each Operational Amplifier. Supply Voltage V+ = 5V, V- = 0V, Unless Otherwise Specified PARAMETER TEST CONDITIONS TEMP ( oC) CA158, CA258 CA358, LM358 CA2904, LM2904 MIN TYP MAX MIN TYP MAX MIN TYP MAX UNITS Input Offset Voltage (Note 9) 25 - 2 5 - 2 7 - 2 7 mV Full - - 7 - - 9 - - 10 mV Average Input Offset Voltage Drift RS = 0Ω Full - 7 - - 7 - - 7 - µV/oC Input Common Mode Voltage Range (Note 8) V+ = 30V 25 0 - V+ - 1.5 0 - V+ - 1.5 0 - V+ - 1.5 V V+ = 30V Full 0 - V+ -2 0 - V+ -2 0 - V+ -2 V Common Mode Rejection Ratio DC 25 70 85 - 65 70 - 50 70 - dB Power Supply Rejection Ratio DC 25 65 100 - 65 100 - 50 100 - dB Input Bias Current (Note 7) II+ or II- 25 - 45 150 - 45 250 - 45 250 nA II+ or II- Full - 40 300 - 40 500 - 40 500 nA Input Offset Current II+ - II - 25 - 3 30 - 5 50 - 5 50 nA II+ - II - Full - - 100 - - 150 - 45 200 nA Average Input Offset Current Drift Full - 10 - - 10 - - 10 - pA/oC Large Signal Voltage Gain RL ≥ 2kΩ, V+ = 15V (For Large VO Swing) 25 50 100 - 25 100 - - 100 - kV/V Output Voltage Swing RL = 2kΩ 25 0 - V+ - 1.5 0 - V+ - 1.5 0 - V+ - 1.5 V CA158, CA158A, CA258, CA258A, CA358, CA358A, CA2904, LM358, LM2904
cA158,cA158A,cA258,CA258A,cA358,cA358A,cA2904,LM358,LM2904 Electrical Specifications Values Apply for Each Operational Amplifier. Supply Voltage V+= 5V, V-=0V, cA158,cA258 cA358LM358 cA2904,LM2904 TEMP PARAMETER CONDITIONS (oC) MIN TYP MAX MIN TYP MAX MIN TYP MAXUNITS Source VI+=+1V. Vr-=0V Current V+=15V v+=15V V+=0V,v=1V 2 12 12 50 Vo= 200mv Short Circuit RL=0S2 60 Output Current(Note 2) Crosstalk Total Supply Current RL u 1.2mA RL=∞,+=30VFu 15 1.5 NOTES: 7. Due to the PNP input stage the direction of the input current is out of the IC. No loading change exists on the input lines because the current is essentially constant, independent of the state of the output. 8. The input signal voltage and the input common mode voltage should not be allowed to go negative by more than 0. 3v. The positive limit of the is v+-1 either or both inputs can go to +32 9. Vo =1.4V, Rs 0Q with V+ from 5V to 30v, and over the full input common mode voltage range(ov to V+-15v) Schematic Diagram ONE OF TWO OPERATIONAL AMPLIFIERS 6 Q1
4 Output Current Source VI+ = +1V, VI- = 0V, V+ = 15V 25 20 40 - 20 40 - 20 40 - mA Sink VI+ = 0V, VI- = 1V, V+ = 15V 25 10 20 - 10 20 - 10 20 - mA VI+ = 0V, VI- = 1V, VO = 200mV 25 12 50 - 12 50 - - - - µA Short Circuit Output Current (Note 2) RL = 0Ω 25 - 40 60 - 40 60 - 40 60 mA Crosstalk f = 1 to 20kHz (Input Referred) 25 - -120 - - -120 - - -120 - dB Total Supply Current RL = ∞ Full - 0.7 1.2 - 0.7 1.2 - 0.7 1.2 mA RL = ∞, V+ = 30V Full - 1.5 3 - 1.5 3 - 1.5 3 mA NOTES: 7. Due to the PNP input stage the direction of the input current is out of the IC. No loading change exists on the input lines because the current is essentially constant, independent of the state of the output. 8. The input signal voltage and the input common mode voltage should not be allowed to go negative by more than 0.3V. The positive limit of the common mode voltage range is V+ - 1.5V, but either or both inputs can go to +32V without damage. 9. VO = 1.4V, RS = 0Ω with V+ from 5V to 30V, and over the full input common mode voltage range (0V to V+ - 1.5V). Electrical Specifications Values Apply for Each Operational Amplifier. Supply Voltage V+ = 5V, V- = 0V, Unless Otherwise Specified (Continued) PARAMETER TEST CONDITIONS TEMP ( oC) CA158, CA258 CA358, LM358 CA2904, LM2904 MIN TYP MAX MIN TYP MAX MIN TYP MAX UNITS Schematic Diagram ONE OF TWO OPERATIONAL AMPLIFIERS 8 2 3 4 1 5 6 7 INPUTS - + 6µA 4µA 100 µA V+ CCOMP 50µA Q1 Q2 Q3 Q4 Q8 Q9 Q10 Q11 Q12 Q13 Q6 Q5 Q7 VO RSC TO 2 TO 2 2 V- + - CA158, CA158A, CA258, CA258A, CA358, CA358A, CA2904, LM358, LM2904
cA158,cA158A,cA258,CA258A,cA358,cA358A,cA2904,LM358,LM2904 Typical Performance Curves =30v 乏u5 T NEGATIVE POSITIVE E2o54 TEMPERATURE SUPPLY VOLTAGE M FIGURE 1 INPUT VOLTAGE RANGE VS SUPPLY VOLTAGE FIGURE 2 INPUT CURRENT VS AMBIENT TEMPERATURE zEz zoFzEouu8 TA=0°cTo125°c 7.5Dc -55°c 1015202530 1K 100K INPUT FREQUENCY(Hz) FIGURE 3. SUPPLY CURRENT DRAIN VS SUPPLY VOLTAGE FIGURE 4. COMMON MODE REJECTION RATIO VS INPUT 140 TA=25°c 10MQ 0.1uF RL= 20kQ2 巴至u8. 巴至u88 3 v+/2○ TA=40≤TA≤85°C 1101001K10K100K1M POSITIVE SUPPLY VOLTAGE ( V FREQUENCY(Hz) FIGURE 5. VOLTAGE GAIN VS SUPPLY VOLTAGE FIGURE 6. OPEN-LOOP FREQUENCY RESPONSE Intersil
5 Typical Performance Curves FIGURE 1. INPUT VOLTAGE RANGE vs SUPPLY VOLTAGE FIGURE 2. INPUT CURRENT vs AMBIENT TEMPERATURE FIGURE 3. SUPPLY CURRENT DRAIN vs SUPPLY VOLTAGE FIGURE 4. COMMON MODE REJECTION RATIO vs INPUT FREQUENCY FIGURE 5. VOLTAGE GAIN vs SUPPLY VOLTAGE FIGURE 6. OPEN-LOOP FREQUENCY RESPONSE 5 10 15 0 5 10 15 20 INPUT VOLTAGE (V) SUPPLY VOLTAGE (V) POSITIVE NEGATIVE TEMPERATURE (oC) INPUT CURRENT (nA) -75 -50 -25 0 25 50 75 100 125 0 10 20 30 40 50 60 VICR = 0V V+ = 30V 15V 5V 4 3 2 1 0 5 10 15 20 25 30 POSITIVE SUPPLY VOLTAGE (V) SUPPLY CURRENT DRAIN (mA) TA = 0oC TO 125oC -55oC ID V+ mA - + 120 100 80 60 40 20 0 100 1K 10K 100K 1M COMMON MODE REJECTION RATION (dB) INPUT FREQUENCY (Hz) +7.5VDC 100K 100 100 100K -7.5VDC VO VIN + - + POSITIVE SUPPLY VOLTAGE (V) OPEN LOOP VOLTAGE GAIN (dB) 0 10 20 30 40 0 25 50 75 100 125 150 2kΩ TA = 25oC RL = 20kΩ 140 120 100 80 60 40 20 0 1 10 100 1K 10K 100K 1M 10M FREQUENCY (Hz) OPEN-LOOP VOLTAGE GAIN (dB) TA = -40 ≤ TA ≤ 85oC V+ = 26V V+ = 10 TO 15V 10MΩ V+ VO V+ / 2 VI 0.1µF - + CA158, CA158A, CA258, CA258A, CA358, CA358A, CA2904, LM358, LM2904
cA158,cA158A,cA258,CA258A,cA358,cA358A,cA2904,LM358,LM2904 Typical Performance Curves (continued) ==三 之 sEu548 d OUTPUT TIME (us) FIGURE7 VOLTAGE FOLLOWER PULSE RESPONSE FIGURE8. VOLTAGE FOLLOWER PUL SE RESPONSE (LARGE SIGNAL (SMALL SIGNAL TA ikE 乏u85 zu5 10K 100K 20 POSITIVE SUPPLY VOLTAGE ( FIGURE 9. LARGE-SIGNAL FREQUENCY RESPONSE FIGURE 10 INPUT CURRENT VS SUPPLY VOLTAGE V+=+15 Vpc v〓+30V v+2 ugH>Ha lo 4INDEPENDENT OF V T=25°c 乏u95e TA=25°c 0.001 0.001 0.01 OUTPUT SOURCE CURRENT(mA) OUTPUT SINK CI GURE 11. OUTPUT SOURCE CURRENT CHARACTERISTICS FIGURE 12. OUTPUT SINK CURRENT CHARACTERISTICS 6 intersil
6 FIGURE 7. VOLTAGE FOLLOWER PULSE RESPONSE (LARGE SIGNAL) FIGURE 8. VOLTAGE FOLLOWER PULSE RESPONSE (SMALL SIGNAL) FIGURE 9. LARGE-SIGNAL FREQUENCY RESPONSE FIGURE 10. INPUT CURRENT vs SUPPLY VOLTAGE FIGURE 11. OUTPUT SOURCE CURRENT CHARACTERISTICS FIGURE 12. OUTPUT SINK CURRENT CHARACTERISTICS Typical Performance Curves (Continued) TA = 25oC V+ = 15V RL = 2kΩ 4 3 2 1 0 10 20 30 40 4 3 2 1 0 OUTPUT VOLTAGE (V) INPUT VOLTAGE (V) TIME (µs) 0 OUTPUT INPUT TA = 25oC V+ = 30V 500 450 400 350 300 250 0 1 23 45 6 7 8 9 TIME (µs) OUTPUT VOLTAGE (mV) VO VI 50pF - + 20 15 10 5 0 1K 10K 100K 1M FREQUENCY (Hz) OUTPUT VOLTAGE SWING (V) TA = 25oC 1kΩ 100kΩ +15V 2kΩ +7V VO VI + - TA = 25oC 75 50 25 0 10 20 30 40 POSITIVE SUPPLY VOLTAGE (V) INPUT CURRENT (nA) 0 8 7 6 5 4 3 2 1 0.001 0.01 0.1 1 10 100 OUTPUT VOLTAGE (V) (REFERENCED TO V+) OUTPUT SOURCE CURRENT (mA) INDEPENDENT OF V+ TA = 25oC V+ V+ / 2 IO+ VO + - 10 1 0.1 0.01 OUTPUT VOLTAGE (V) 0.001 0.01 0.1 1 10 100 OUTPUT SINK CURRENT (mA) V+ = +5VDC V+ = +15 VDC V+ = +30VDC V+ / 2 V+ - + TA = 25oC VO IO CA158, CA158A, CA258, CA258A, CA358, CA358A, CA2904, LM358, LM2904
cA158,cA158A,cA258,CA258A,cA358,cA358A,cA2904,LM358,LM2904 Typical Performance Curves (continued) 000 v=15V uocomHa5 75-50-250255075100125 TEMPERATURE°c FIGURE 13. OUTPUT CURRENT VS AMBIENT TEMPERATURE Metallization Mask Layout 40506066 6977 102-0.254) (1600-1803 Dimensions in parentheses are in millimeters and derived from the basic inch dimensions as indicated. Grid gradua- tions The photographs and dimensions represent a chip when it is part of the wafer. When the wafer is cut into chips, the cleavage angles are 57 instead of 90 with respect to the face of the chip. Therefore, the isolated chip is actually 7mils (0. 17mm)larger in both dimensions All Intersil semiconductor products are manufactured, assembled and tested under iso9000 quality systems certification Intersil semiconductor products are sold by description only Intersil Corporation reserves the night to make changes in circuit design and/or sp an atents o from its use. No lice rwise under any patent or patent nights ForinformationregardingIntersilCorporationanditsproductsseewebsitehttp://www.intersil.com intersil
7 All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com FIGURE 13. OUTPUT CURRENT vs AMBIENT TEMPERATURE Typical Performance Curves (Continued) TEMPERATURE (oC) OUTPUT SOURCE CURRENT (mA) -75 -50 -25 0 25 50 75 100 125 0 10 20 30 40 50 60 70 V+ = 15V Metallization Mask Layout 72 70 60 50 40 30 20 10 0 0 10 20 30 40 50 60 66 69 - 77 (1.753 - 1.956) 63 - 71 (1.600 - 1.803) 4 - 10 (0.102 - 0.254) Dimensions in parentheses are in millimeters and derived from the basic inch dimensions as indicated. Grid graduations are in mils (10-3 inch). The photographs and dimensions represent a chip when it is part of the wafer. When the wafer is cut into chips, the cleavage angles are 57o instead of 90o with respect to the face of the chip. Therefore, the isolated chip is actually 7mils (0.17mm) larger in both dimensions. CA158, CA158A, CA258, CA258A, CA358, CA358A, CA2904, LM358, LM2904