查询74LS08供应商 SN7ALSO8 Quad 2-Input AND Gate 应4 312 11098 ON Semiconductor Formerly a Dimsion of Motorola http:/lonsemi.com LOW OWER SCHOTTKY GND GUARANTEED OPERATING RANGES Parameter yp Max Unit 4.7550525V Operating Ambient Temperature Range PLASTIC Output Current- High -04mA N SUFFIX Output Current-LOW 8 CASE 646 D SUFFIX CASE 751A ORDERING INFORMATION Device SN74LSO8N SN74LSO8D 14 Pin 2500/ Tape& Reel 我6 stries LLC. 1999 Publication order number SN7ALSO8/D 维库 www.dzsc.com
Semiconductor Components Industries, LLC, 1999 December, 1999 – Rev. 6 1 Publication Order Number: SN74LS08/D 14 13 12 11 10 9 123456 VCC 8 7 GND GUARANTEED OPERATING RANGES Symbol Parameter Min Typ Max Unit VCC Supply Voltage 4.75 5.0 5.25 V TA Operating Ambient Temperature Range 0 25 70 °C IOH Output Current – High –0.4 mA IOL Output Current – Low 8.0 mA LOW POWER SCHOTTKY SOIC D SUFFIX CASE 751A http://onsemi.com PLASTIC N SUFFIX CASE 646 14 1 14 1 Device Package Shipping ORDERING INFORMATION SN74LS08N 14 Pin DIP 2000 Units/Box SN74LS08D 14 Pin 2500/Tape & Reel 查询74LS08供应商 查询74LS08供应商
SN74LS08 DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits Symbol Parameter Max Test Conditions Input HIGH Voltage Guaranteed Input HIGH Voltage fo All Inputs ut LOW Voltage Guaranteed Input LOW Voltage for All Inputs Input Clamp Diode Voltage 1.5 Vcc = MIN, IIN =-18 mA 3.5 VOH Output HIGH Voltage Vcc=MIN, IOH= MAX, VIN= VIH or ViL per Truth Table VoL Output LOW Voltage 0.5 OL=8.0 ma per Truth Table MAX, VIN=2.7 V H input HIGH Current Vcc= MAX, VIN=7.0V Input LOW Current -04 cc= MAX, VIN=0.4 V Short Circuit Current(Note 1) -100 mA Vcc=MAX Power Supply Current Total, Output HIGH Vcc= MAX otal, Output LOW Note 1: Not more than one output should be shorted at a time, nor for more than 1 second AC CHARACTERISTICS (TA=25C) Symbol Typ Max Test Conditions tPLH Turn-Off Delay, Input to Output 8.0 15 CC=5.0V tphL Turn-On Delay, Input to Output 10 20 CL=15 pF 我6 http://onsemi.com 维库 www.dzsc.com
SN74LS08 http://onsemi.com 2 DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits Symbol Parameter Min Typ Max Unit Test Conditions VIH Input HIGH Voltage 2.0 V Guaranteed Input HIGH Voltage for All Inputs VIL Input LOW Voltage 0.8 V Guaranteed Input LOW Voltage for All Inputs VIK Input Clamp Diode Voltage –0.65 –1.5 V VCC = MIN, IIN = –18 mA VOH Output HIGH Voltage 2.7 3.5 V VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table VOL Output LOW Voltage 0.25 0.4 V IOL = 4.0 mA VCC = VCC MIN, VOL Out ut LOW Voltage VIN = VIL or VIH 0.35 0.5 V IOL = 8.0 mA VIN = VIL or VIH per Truth Table IIH Input HIGH Current 20 µA VCC = MAX, VIN = 2.7 V IIH In ut HIGH Current 0.1 mA VCC = MAX, VIN = 7.0 V IIL Input LOW Current –0.4 mA VCC = MAX, VIN = 0.4 V IOS Short Circuit Current (Note 1) –20 –100 mA VCC = MAX Power Supply Current ICC Total, Output HIGH 4.8 mA VCC = MAX Total, Output LOW 8.8 Note 1: Not more than one output should be shorted at a time, nor for more than 1 second. AC CHARACTERISTICS (TA = 25°C) Limits Symbol Parameter Min Typ Max Unit Test Conditions tPLH Turn–Off Delay, Input to Output 8.0 15 ns VCC = 5.0 V tPHL Turn–On Delay, Input to Output 10 20 ns CC CL = 15 pF
SN74LS08 PACKAGE DIMENSIONS N SUFFIX PLASTIC PACKAGE AsE646-06 ISSUE M MENSIONING AND TOLERANCING PER ANSI 2 CONTROLLING DIMENSION 3. DIMENSION L TO CENTER OF LEADS WHEN 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH 5. ROUNDED CORNERS OPT Hk- 01300 D SUFFIX PLASTIC SOIC PACKAGE CASE 751A-03 ISSUEF 1. DIMENSIONING AND TOLERANCING PER ANSI 2. CONTROLLING DIMENSION: MILLIMETER 4. MAXIMUM MOLD PROTRUSION 0.15(0.006) 由由HHH 05000 IN EXCESS OF THE D DIMENSION AT R SEATING 到D14PL 由025000BA( 我6 http://onsemi.com 维库 www.dzsc.com
SN74LS08 http://onsemi.com 3 PACKAGE DIMENSIONS 1 7 14 8 B A DIM MIN MAX MIN MAX INCHES MILLIMETERS A 0.715 0.770 18.16 18.80 B 0.240 0.260 6.10 6.60 C 0.145 0.185 3.69 4.69 D 0.015 0.021 0.38 0.53 F 0.040 0.070 1.02 1.78 G 0.100 BSC 2.54 BSC H 0.052 0.095 1.32 2.41 J 0.008 0.015 0.20 0.38 K 0.115 0.135 2.92 3.43 L M ––– 10 ––– 10 N 0.015 0.039 0.38 1.01 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. F H G D K C SEATING PLANE N –T– 14 PL 0.13 (0.005) M L M J 0.290 0.310 7.37 7.87 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. –A– –B– G P 7 PL 14 8 1 7 0.25 (0.010) B M M 0.25 (0.010) A M T B S S –T– R X 45 F SEATING PLANE D 14 PL K C M J DIM MIN MAX MIN MAX MILLIMETERS INCHES A 8.55 8.75 0.337 0.344 B 3.80 4.00 0.150 0.157 C 1.35 1.75 0.054 0.068 D 0.35 0.49 0.014 0.019 F 0.40 1.25 0.016 0.049 G 1.27 BSC 0.050 BSC J 0.19 0.25 0.008 0.009 K 0.10 0.25 0.004 0.009 M 0 7 0 7 P 5.80 6.20 0.228 0.244 R 0.25 0.50 0.010 0.019 D SUFFIX PLASTIC SOIC PACKAGE CASE 751A–03 ISSUE F N SUFFIX PLASTIC PACKAGE CASE 646–06 ISSUE M
SN74LS08 ctor and C) are trademarks of Semiconducto ts Industries, LLC (SCILLC). SCILLC reserves the right to make changes products for any I dated for each customer application by cust SCILLC produc death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold se. even if such claim alleges that ScILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity Affirmative Action Employer. PUBLICATION ORDERING INFORMATION erica Literature Fulfillment ASIA/PACIFIC: LDC for ON Semiconductor- Asia Support (Tue-Fri 9:00am to 1: 00pm, Hong Kong Time) oll Free from Hong Kong 800-4422-3781 03-675-21750r800-344-3860 Toll Free UsA/canada ax 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email:Oniit@HibbeRtco.com conductor, Japan Customer Focus Center Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-8549 N. American Technical Support: 800-282-9855 Toll Free USA/Canada Emailr14153@onsemi.com EUROPE: LDC for ON Semiconductor- European S German Phone: (+1)303-308-7140(M-F 2: 30pm to 5: 00pm Munich Time) Fax Response Line: 303-675-2167 800-344-3810 Toll Free USA/Canada French Phone: (+1)303-308-7141(M-F 2: 30pm to 5: 00pm Toulouse Time OnSemiconductorWebsitehttp:/lonsemi.c English Phone:(1)303-308-7142 (M-F 1: 30pm to 5: 00pm UK Time) For additional information, please contact your local 我6 SN74LS08/D 维库 www.dzsc.com
SN74LS08 http://onsemi.com 4 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong 800–4422–3781 Email: ONlit–asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–8549 Phone: 81–3–5487–8345 Email: r14153@onsemi.com Fax Response Line: 303–675–2167 800–344–3810 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. SN74LS08/D North America Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: ONlit@hibbertco.com N. American Technical Support: 800–282–9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor – European Support German Phone: (+1) 303–308–7140 (M–F 2:30pm to 5:00pm Munich Time) Email: ONlit–german@hibbertco.com French Phone: (+1) 303–308–7141 (M–F 2:30pm to 5:00pm Toulouse Time) Email: ONlit–french@hibbertco.com English Phone: (+1) 303–308–7142 (M–F 1:30pm to 5:00pm UK Time) Email: ONlit@hibbertco.com