Delin, K.A., Orlando, T.P. Superconductivity The Electrical Engineering Handbook Ed. Richard C. Dorf Boca raton crc Press llc. 2000
Delin, K.A., Orlando, T.P. “Superconductivity” The Electrical Engineering Handbook Ed. Richard C. Dorf Boca Raton: CRC Press LLC, 2000
53 Superconductivity Kevin A. Delin 53.1 Introduction Terry P. Orlando 53.2 General Electromagnetic Properties Massachusetts Institute of 53.3 Superconducting Electronics 53.4 Types of Superconductors 53.1 Introduction The fundamental idea behind all of a superconductor's unique properties is that superconductivity is a quantum mechanical phenomenon on a macroscopic scale created when the motions of individual electrons are corre- lated. According to the theory developed by John Bardeen, Leon Cooper, and Robert Schrieffer(BCS theory) nis correlation takes place when two electrons couple to form a Cooper pair For our purposes, we may therefore consider the electrical charge carriers in a superconductor to be Cooper pairs(or more colloquially, superelec rons)with a mass m* and charge twice those of normal electrons. The average distance between the two electrons in a Cooper pair is known as the coherence length, s. Both the coherence length and the binding energy of two electrons in a Cooper pair, 24, depend upon the particular superconducting material. Typically, the coherence length is many times larger than the interatomic spacing of a solid, and so we should not think of Cooper pairs as tightly bound electron molecules. Instead, there are many other electrons between those of a specific Cooper pair allowing for the paired electrons to change partners on a time scale of h/(2A)where h Planck's constant If we prevent the Cooper pairs from forming by ensuring that all the electrons are at an energy greater than the binding energy, we can destroy the superconducting phenomenon. This can be accomplished, for example, with thermal energy. In fact, according to the BCS theory, the critical temperature, T. associated with this 2△ ≈3.5 kaT where kg is Boltzmanns constant. For low critical temperature(conventional)superconductors, 24 is typically on the order of 1 meV, and we see that these materials must be kept below temperatures of about 10 K to exhibit their unique behavior. High critical temperature superconductors, in contrast, will superconduct up to temperatures of about 100 K, which is attractive from a practical view because the materials can be coole cheaply using liquid nitrogen. Other types of depairing energy are kinetic, resulting in a critical current density J e, and magnetic, resulting in a critical field He. To summarize, a superconductor must be maintained under the appropriate temperature, electrical current density, and magnetic field conditions to exhibit its speci properties. An example of this phase space is shown in Fig. 53.1 c 2000 by CRC Press LLC
© 2000 by CRC Press LLC 53 Superconductivity 53.1 Introduction 53.2 General Electromagnetic Properties 53.3 Superconducting Electronics 53.4 Types of Superconductors 53.1 Introduction The fundamental idea behind all of a superconductor’s unique properties is thatsuperconductivity is a quantum mechanical phenomenon on a macroscopic scale created when the motions of individual electrons are correlated. According to the theory developed by John Bardeen, Leon Cooper, and Robert Schrieffer (BCS theory), this correlation takes place when two electrons couple to form a Cooper pair. For our purposes, we may therefore consider the electrical charge carriers in a superconductor to be Cooper pairs (or more colloquially, superelectrons) with a mass m* and charge q* twice those of normal electrons. The average distance between the two electrons in a Cooper pair is known as the coherence length, j. Both the coherence length and the binding energy of two electrons in a Cooper pair, 2D, depend upon the particular superconducting material. Typically, the coherence length is many times larger than the interatomic spacing of a solid, and so we should not think of Cooper pairs as tightly bound electron molecules. Instead, there are many other electrons between those of a specific Cooper pair allowing for the paired electrons to change partners on a time scale of h/(2D) where h is Planck’s constant. If we prevent the Cooper pairs from forming by ensuring that all the electrons are at an energy greater than the binding energy, we can destroy the superconducting phenomenon. This can be accomplished, for example, with thermal energy. In fact, according to the BCS theory, the critical temperature, Tc , associated with this energy is (53.1) where kB is Boltzmann’s constant. For low critical temperature (conventional) superconductors, 2D is typically on the order of 1 meV, and we see that these materials must be kept below temperatures of about 10 K to exhibit their unique behavior. High critical temperature superconductors, in contrast, will superconduct up to temperatures of about 100 K, which is attractive from a practical view because the materials can be cooled cheaply using liquid nitrogen. Other types of depairing energy are kinetic, resulting in a critical current density Jc , and magnetic, resulting in a critical field Hc. To summarize, a superconductor must be maintained under the appropriate temperature, electrical current density, and magnetic field conditions to exhibit its special properties. An example of this phase space is shown in Fig. 53.1. 2 3 5 D k TB c ª . Kevin A. Delin Jet Propulsion Laboratory Terry P. Orlando Massachusetts Institute of Technology
Critica ensity(1 FIGURE 53.1 The phase space for the superconducting alloy niobium-titanium. The material is superconducting inside the volume of phase space indicated. 53.2 General Electromagnetic Properties The hallmark electromagnetic properties of a superconductor are its ability to carry a static current without any resistance and its ability to exclude a static magnetic flux from its interior. It is this second property, known the Meissner effect, that distinguishes a superconductor from merely being a perfect conductor (which conserves the magnetic flux in its interior). Although superconductivity is a manifestly quantum mechanical phenomenon, a useful classical model can be constructed around these two properties. In this section, we will outline the rationale for this classical model, which is useful in engineering applications such as waveguides The zero dc resistance criterion implies that the superelectrons move unimpeded. The electromagnetic energy density, w, stored in a superconductor is therefore μlH 2 where the first two terms are the familiar electric and magnetic energy densities, respectively. (Our electromag netic notation is standard: E is the permittivity, u, is the permeability, E is the electric field, and the magnetic lux density, B, is related to the magnetic field, H, via the constitutive law B=H, H )The last term represents the kinetic energy associated with the undamped superelectrons' motion(n* and v, are the superelectrons density and velocity, respectively). Because the supercurrent density, J,, is related to the superelectron velocity y J, = nav,, the kinetic energy term can be rewritten J where a is defined as (534) e 2000 by CRC Press LLC
© 2000 by CRC Press LLC 53.2 General Electromagnetic Properties The hallmark electromagnetic properties of a superconductor are its ability to carry a static current without any resistance and its ability to exclude a static magnetic flux from its interior. It is this second property, known as the Meissner effect, that distinguishes a superconductor from merely being a perfect conductor (which conserves the magnetic flux in its interior). Although superconductivity is a manifestly quantum mechanical phenomenon, a useful classical model can be constructed around these two properties. In this section, we will outline the rationale for this classical model, which is useful in engineering applications such as waveguides and high-field magnets. The zero dc resistance criterion implies that the superelectrons move unimpeded. The electromagnetic energy density, w, stored in a superconductor is therefore (53.2) where the first two terms are the familiar electric and magnetic energy densities, respectively. (Our electromagnetic notation is standard: e is the permittivity, mo is the permeability, E is the electric field, and the magnetic flux density, B, is related to the magnetic field, H, via the constitutive law B = moH.) The last term represents the kinetic energy associated with the undamped superelectrons’ motion (n* and vs are the superelectrons’ density and velocity, respectively). Because the supercurrent density, Js , is related to the superelectron velocity by Js = n*q*vs , the kinetic energy term can be rewritten (53.3) where L is defined as (53.4) FIGURE 53.1 The phase space for the superconducting alloy niobium–titanium. The material is superconducting inside the volume of phase space indicated. w n m v o s = + m + 1 2 1 2 2 2 2 eE H2 * * n m s s * * 1 2 1 2 2 2 v Ê Ë Á ˆ ¯ ˜ = LJ L = ( ) m n q * * * 2
Assuming that all the charge carriers are superelectrons, there is no power dissipation inside the supercon ductor, and so Poynting s theorem over a volume V may be written x hdv (53.5) where the left side of the expression is the power flowing into the region. By taking the time derivative of the energy density and appealing to Faraday's and Ampere's laws to find the time derivatives of the field quantities, ve find that the only way for Poynting's theorem to be satisfied is if (53.6) This relation, known as the first London equation(after the London brothers, Heinz and Fritz), is thus necessary if the superelectrons have no resistance to their motion Equation (53. 6)reveals that the superelectrons' inertia creates a lag between their motion and that of an pplied electric field. As a result, a superconductor will support a time-varying voltage drop. The impedance associated with the supercurrent is therefore inductive and it will be useful to think of A as a kinetic inductance created by the correlated motion of the Cooper pairs If the first London equation is substituted into Faraday's law,VxE=-(aB/ar), and integrated with respect to time, the second London equation results V×(AJ.)=-B (53.7) where the constant of integration has been defined to be zero. This choice is made so that the second London equation is consistent with the Meissner effect as we now demonstrate. Taking the curl of the quasi-static form of Amperes law, VX H=J,, results in the expression V2B=-kV X J,, where a vector identity, VxVX C v(V. C)-V2C; the constitutive relation, B=kH; and Gauss's law, V.B=0, have been used By now appealing to the second London equation, we obtain the vector Helmholtz equatio V-B B=0 where the penetration depth is defined n*(q) From Eq. (53.8), we find that a flux density applied parallel to the surface of a semi-infinite superconductor will decay away exponentially from the surface on a spatial length scale of order A. In other words, a bulk superconductor will exclude an applied flux as predicted by the Meissner effect The London equations reveal that there is a characteristic length A over which electromagnetic fields can change inside a superconductor. This penetration depth is different from the more familiar skin depth of electromagnetic theory, the latter being a frequency-dependent quantity. Indeed, the penetration depth at zero temperature is a distinct material property of a particular superconductor Notice that A is sensitive to the number of correlated electrons( the superelectrons)in the material. As previously discussed, this number is a function of temperature and so only at t=o do all the electrons that usually conduct ohmically participate in the Cooper pairing. For intermediate temperatures, 0< T<T, there c2000 by CRC Press LLC
© 2000 by CRC Press LLC Assuming that all the charge carriers are superelectrons, there is no power dissipation inside the superconductor, and so Poynting’s theorem over a volume V may be written (53.5) where the left side of the expression is the power flowing into the region. By taking the time derivative of the energy density and appealing to Faraday’s and Ampère’s laws to find the time derivatives of the field quantities, we find that the only way for Poynting’s theorem to be satisfied is if (53.6) This relation, known as the first London equation (after the London brothers, Heinz and Fritz), is thus necessary if the superelectrons have no resistance to their motion. Equation (53.6) reveals that the superelectrons’ inertia creates a lag between their motion and that of an applied electric field. As a result, a superconductor will support a time-varying voltage drop. The impedance associated with the supercurrent is therefore inductive and it will be useful to think of L as a kinetic inductance created by the correlated motion of the Cooper pairs. If the first London equation is substituted into Faraday’s law, ¹ ¥ E = –(]B/]t), and integrated with respect to time, the second London equation results: (53.7) where the constant of integration has been defined to be zero. This choice is made so that the second London equation is consistent with the Meissner effect as we now demonstrate. Taking the curl of the quasi-static form of Ampère’s law, ¹ ¥ H = Js , results in the expression ¹2 B = –mo ¹ ¥ Js , where a vector identity, ¹ ¥ ¹ ¥ C = ¹(¹ • C) – ¹2 C; the constitutive relation, B = moH; and Gauss’s law, ¹ • B = 0, have been used. By now appealing to the second London equation, we obtain the vector Helmholtz equation (53.8) where the penetration depth is defined (53.9) From Eq. (53.8), we find that a flux density applied parallel to the surface of a semi-infinite superconductor will decay away exponentially from the surface on a spatial length scale of order l. In other words, a bulk superconductor will exclude an applied flux as predicted by the Meissner effect. The London equations reveal that there is a characteristic length l over which electromagnetic fields can change inside a superconductor. This penetration depth is different from the more familiar skin depth of electromagnetic theory, the latter being a frequency-dependent quantity. Indeed, the penetration depth at zero temperature is a distinct material property of a particular superconductor. Notice that l is sensitive to the number of correlated electrons (the superelectrons) in the material. As previously discussed, this number is a function of temperature and so only at T = 0 do all the electrons that usually conduct ohmically participate in the Cooper pairing. For intermediate temperatures, 0 < T < Tc , there - —× ¥ ( ) = Ú Ú E H dv w t dv V V ¶ ¶ E J = ( ) ¶ ¶t L s — ¥ (LJ B ) = - s —- = 2 2 1 B B 0 l l º m = ( ) m L o o m n q * * * 2
Channel E ACT) FIGURE 53.2 A lumped element model of a superconductor. are actually two sets of interpenetrating electron fluids: the uncorrelated electrons providing ohmic conduction and the correlated ones creating supercurrents. This two-fluid model is a useful way to build temperature effects into the london relations Under the two-fluid model, the electrical current density, J, is carried by both the uncorrelated(normal electrons and the superelectrons: J=J,+ J, where J, is the normal current density. The two channels are modeled in a circuit as shown in Fig. 53.2 by a parallel combination of a resistor (representing the ohmic hannel)and an inductor(representing the superconducting channel). To a good approximation, the respective temperature dependences of the conductor and inductor are forT≤T (53.10) T A(T)=A0) fort< t (53.11) (T/T) where o. is the dc conductance of the normal channel. Strictly speaking, the normal channel should also contain an inductance representing the inertia of the normal electrons, but typically such an inductor contrib utes negligibly to the overall electrical response. )Since the temperature-dependent penetration depth is defined as A(D=A(T)/u,, the effective conductance of a superconductor in the sinusoidal steady state is =+ (53.12) where the explicit temperature dependence notation has been suppressed. should be noted that the temperature dependencies given in Equations(53.10)and (53. 11)are not precisely correct for the high-T materials. It has been suggested that this is because the angular momentum of the electrons forming a Cooper pair in high-T materials is different from that in low-T ones. Nevertheless, the wo-fluid picture of transport and its associated constitutive law, Eq (53. 12), are still valid for high-T super conductors Most of the important physics associated with the classical model is embedded in Eq. (53. 12). As is cle from the lumped element model, the relative importance of the normal and superconducting channels is a e 2000 by CRC Press LLC
© 2000 by CRC Press LLC are actually two sets of interpenetrating electron fluids: the uncorrelated electrons providing ohmic conduction and the correlated ones creating supercurrents. This two-fluid model is a useful way to build temperature effects into the London relations. Under the two-fluid model, the electrical current density, J, is carried by both the uncorrelated (normal) electrons and the superelectrons: J = Jn + Js where Jn is the normal current density. The two channels are modeled in a circuit as shown in Fig. 53.2 by a parallel combination of a resistor (representing the ohmic channel) and an inductor (representing the superconducting channel). To a good approximation, the respective temperature dependences of the conductor and inductor are (53.10) and (53.11) where so is the dc conductance of the normal channel. (Strictly speaking, the normal channel should also contain an inductance representing the inertia of the normal electrons, but typically such an inductor contributes negligibly to the overall electrical response.) Since the temperature-dependent penetration depth is defined as l(T) = , the effective conductance of a superconductor in the sinusoidal steady state is (53.12) where the explicit temperature dependence notation has been suppressed. It should be noted that the temperature dependencies given in Equations (53.10) and (53.11) are not precisely correct for the high-Tc materials. It has been suggested that this is because the angular momentum of the electrons forming a Cooper pair in high-Tc materials is different from that in low-Tc ones. Nevertheless, the two-fluid picture of transport and its associated constitutive law, Eq. (53.12), are still valid for high-Tc superconductors. Most of the important physics associated with the classical model is embedded in Eq. (53.12). As is clear from the lumped element model, the relative importance of the normal and superconducting channels is a FIGURE 53.2 A lumped element model of a superconductor. s s ˜ o o c c T T c T T ( ) = ( ) T T Ê Ë Á ˆ ¯ ˜ £ 4 for L T L T T T T c ( ) c = ( ) - ( ) Ê Ë Á Á ˆ ¯ ˜ ˜ 0 £ 1 1 4 for L(T) mo § s s w l = + m ˜ o o j 1 2
nction not only of temperature but also of frequency. The familiar L/R time constant, here equal to Ao delineates the frequency regimes where most of the total current is carried by J. (if Ad. >>1)or J,(if oAo < 1). This same result can also be obtained by comparing the skin depth associated with the normal channel,8=/2/((. 0,), to the penetration depth to see which channel provides more field screeningIn addition, it is straightforward to use Eq.(53.12)to rederive Poynting's theorem for systems that involve V(EX H)dv= d +=l (T) dv o Using this expression, it is possible to apply the usual electromagnetic analysis to find the inductance(Lo), capacitance(Co), and resistance(R,) per unit length along a parallel plate transmission line. The results of such analysis for typical cases are summarized in Table 53.1 53.3 Superconducting electronics The macroscopic quantum nature of superconductivity can be usefully exploited to create a new type of lectronic device. Because all the superelectrons exhibit correlated motion, the usual wave-particle duality normally associated with a single quantum particle can now be applied to the entire ensemble of superelectrons Thus, there is a spatiotemporal phase associated with the ensemble that characterizes the supercurrent flowing If the overall electron correlation is broken, this phase is lost and the material is no longer a superconductor. There is a broad class of structures, however, known as weak links, where the correlation is merely perturbed locally in space rather than outright destroyed. Coloquially, we say that the phase"slips"across the weak link acknowledge the perturbation The unusual properties of this phase slippage were first investigated by Brian Josephson and constitute the central principles behind onducting electronics Josephson found that the phase slippage could be defined as the difference between the macroscopic phases on either side of the weak link. This phase difference, denoted as d, determined the supercurrent, i,, through and voltage, v, across the weak link according to the Josephson (53.14) Φ。 2πdt where I is the critical(maximum) current of the junction and p, is the quantum unit of flux.(The flux quantum has a precise definition in terms of Planck's constant, h, and the electron charge, e: d= h/(2e) 2. x 10-5 Wb). As in the previous section, the correlated motion of the electrons, here represented by the superelectron phase, manifests itself through an inductance. This is straightforwardly demonstrated by taking the time derivative of Eq.(53. 14)and combining this expression with Eq. (53. 15). Although the resulting inductance is nonlinear(it depends on cos ) its relative scale is determined by (53.16) 2πI c2000 by CRC Press LLC
© 2000 by CRC Press LLC function not only of temperature but also of frequency. The familiar L/R time constant, here equal to Ls~ o , delineates the frequency regimes where most of the total current is carried by Jn (if vLs~ o >> 1) or Js (if vLs~ o<< 1). This same result can also be obtained by comparing the skin depth associated with the normal channel, d = , to the penetration depth to see which channel provides more field screening. In addition, it is straightforward to use Eq. (53.12) to rederive Poynting’s theorem for systems that involve superconducting materials: (53.13) Using this expression, it is possible to apply the usual electromagnetic analysis to find the inductance (Lo), capacitance (Co), and resistance (Ro) per unit length along a parallel plate transmission line. The results of such analysis for typical cases are summarized in Table 53.1. 53.3 Superconducting Electronics The macroscopic quantum nature of superconductivity can be usefully exploited to create a new type of electronic device. Because all the superelectrons exhibit correlated motion, the usual wave–particle duality normally associated with a single quantum particle can now be applied to the entire ensemble of superelectrons. Thus, there is a spatiotemporal phase associated with the ensemble that characterizes the supercurrent flowing in the material. If the overall electron correlation is broken, this phase is lost and the material is no longer a superconductor. There is a broad class of structures, however, known as weak links, where the correlation is merely perturbed locally in space rather than outright destroyed. Coloquially, we say that the phase “slips” across the weak link to acknowledge the perturbation. The unusual properties of this phase slippage were first investigated by Brian Josephson and constitute the central principles behind superconducting electronics.Josephson found that the phase slippage could be defined as the difference between the macroscopic phases on either side of the weak link. This phase difference, denoted as f, determined the supercurrent, is, through and voltage, v, across the weak link according to the Josephson equations, (53.14) and (53.15) where Ic is the critical (maximum) current of the junction and Fo is the quantum unit of flux. (The flux quantum has a precise definition in terms of Planck’s constant, h, and the electron charge, e: Fo [ h/(2e) ª 2.068 ¥ 10–15 Wb). As in the previous section, the correlated motion of the electrons, here represented by the superelectron phase, manifests itself through an inductance. This is straightforwardly demonstrated by taking the time derivative of Eq. (53.14) and combining this expression with Eq. (53.15). Although the resulting inductance is nonlinear (it depends on cos f), its relative scale is determined by (53.16) 2 wmos˜ o § ( ) - — × ( ¥ ) = + m + ( ) Ê Ë Á ˆ ¯ ˜ + ( ) Ú Ú Ú E H E H J J 2 2 dv d dt T dv T dv V o s V o n V 1 2 1 2 1 2 1 2 2 e s L ˜ i I s c = sin f v d dt o = F 2p f L I j o c = F 2p
TABLE 53.1 Lumped Circuit Element Parameters Per Unit Length for Typical Transverse Electromagnetic Parallel Plate Waveguides* Transmission Line Geometry 入 Two identical, thin (A >>b) 0,λ bThlb E Two identical, thick(A b) 可入 bThI 匮 lIliM μ,h,p入,6 d One thick(λ<b and one thick(A<< b) ohmic plate "The subscript n refers to parameters associated with a normal(ohmic)plate. Using these expressions, line input impedance, attenuation, and wave velocity can be calculated. a useful quantity for making engineering estimates. For example, the energy scale associated with Josephson oupling is L; I 2=(1。)2兀 A common weak link, known as the Josephson tunnel junction, is made by separating two superconducting films with a very thin(typically 20 A) insulating layer. Such a structure is conveniently analyzed using the sistively and capacitively shunted junction(RCSD)model shown in Fig. 53. 3. Under the RCS] model an ideal lumped junction [described by Eqs. (53.14)and (53. 15)] and a resistor R represent how the weak link structure influences the respective phases of the super and normal electrons. A capacitor C represents the physical capacitance of the sandwich structure. Parasitic capacitance created by the fields around a device interacting with a dielectric substrate is also included in this lumped element. If the ideal lumped junction portion of the circuit is treated as an inductor-like element, many Josephson tunnel junction properties can be calculated with the familiar circuit time constants associated with the model. For example, the quality factor Q of the RCS] circuit can be expressed as e 2000 by CRC Press LLC
© 2000 by CRC Press LLC a useful quantity for making engineering estimates. For example, the energy scale associated with Josephson coupling is LjIc 2 = (IcFo )/2p. A common weak link, known as the Josephson tunnel junction, is made by separating two superconducting films with a very thin (typically 20 Å) insulating layer. Such a structure is conveniently analyzed using the resistively and capacitively shunted junction (RCSJ) model shown in Fig. 53.3. Under the RCSJ model an ideal lumped junction [described by Eqs. (53.14) and (53.15)] and a resistor Rj represent how the weak link structure influences the respective phases of the super and normal electrons. A capacitor Cj represents the physical capacitance of the sandwich structure. Parasitic capacitance created by the fields around a device interacting with a dielectric substrate is also included in this lumped element. If the ideal lumped junction portion of the circuit is treated as an inductor-like element, many Josephson tunnel junction properties can be calculated with the familiar circuit time constants associated with the model. For example, the quality factor Q of the RCSJ circuit can be expressed as TABLE 53.1 Lumped Circuit Element Parameters Per Unit Length for Typical Transverse Electromagnetic Parallel Plate Waveguides* Transmission Line Geometry Lo Co Ro *The subscript n refers to parameters associated with a normal (ohmic) plate. Using these expressions, line input impedance, attenuation, and wave velocity can be calculated. m + m t o h d db 2 2 l et d h 8 4 db o s˜ l d Ê Ë Á ˆ ¯ ˜ m + m t o h d d 2 l et d h 4 3 d o ds l ˜ d Ê Ë Á ˆ ¯ ˜ m + m + m t o n n h d d d l d 2 et d h 1 d n o n d s
FIGURE 53.3 A real Josephson tunnel junction can be modeled deal lumped circuit elements. IcR FIGURE 53. 4 The i-v curves for a Josephson junction: (a)B>>1, and (b)B> 1, the capacitive time constant R; Ci dominates the dynamics of the circuit. Thus, as the bias current is raised from zero, no time-average voltage is created until the critical current I is exceeded. At this point, the junciton switches to a voltage consistent with the breaking of the Cooper pairs, 2A/e, with a time constant L C. Once the junction has latched in the voltage state, however, the capacitor has charged up and the only way for it to discharge is to lower the bias current to zero again. As a result, a device with B >>1 will have a hysteretic current-voltage curve as shown in Fig. 53.4a. Conversely, B I (53.18) In other words, once the supercurrent channel carries its maximum amount of current, the rest of the current is carried through the normal channel Just as the correlated motion of the superelectrons creates the frequency-independent Meissner effect in a bulk superconductor through Faraday's law, so too the macroscopic quantum nature of superconductivity c2000 by CRC Press LLC
© 2000 by CRC Press LLC (53.17) where b is known as the Stewart-McCumber parameter. Clearly, if b >> 1, the capacitive time constant RjCj dominates the dynamics of the circuit. Thus, as the bias current is raised from zero, no time-average voltage is created until the critical current Ic is exceeded. At this point, the junciton switches to a voltage consistent with the breaking of the Cooper pairs, 2D/e, with a time constant . Once the junction has latched in the voltage state, however, the capacitor has charged up and the only way for it to discharge is to lower the bias current to zero again. As a result, a device with b >>1 will have a hysteretic current-voltage curve as shown in Fig. 53.4a. Conversely, b > 1, and (b) b 2 for
allows the possibility of a device whose output voltage is a function of a static magnetic field. If two weak links are connected in parallel, the lumped version of Faraday s law gives the voltage across the second weak link as V2=V,+(da/dt), where a is the total flux threading the loop between the links. Substituting Eq.(53. 15), integrating with respect to time, and again setting the integration constant to zero yields 2-q=(2x@)Φ (53.19) showing that the spatial change in the phase of the macroscopic wavefunction is proportional to the local magnetic flux. The structure described is known as a superconducting quantum interference device(SQuId)an can be used as a highly sensitive magnetometer by biasing it with current and measuring the resulting voltag as a function of magnetic flux. From this discussion, it is apparent that a duality exists in how fields interact with the macroscopic phase: electric fields are coupled to its rate of change in time and magnetic fields are oupled to its rate of change in space 53.4 Types of Superconductors The macroscopic quantum nature of superconductivity also affects the general electromagnetic properties previously discussed. This is most clearly illustrated by the interplay of the characteristic lengths 5, representing the scale of quantum correlations, and A, representing the scale of electromagnetic screening. Consider the scenario where a magnetic field, H, is applied parallel to the surface of a semi-infinite superconductor. The correlations of the electrons in the superconductor must lower the overall energy of the system or else the material would not be superconducting in the first place. Because the critical magnetic field H destroys all the correlations, it is convenient to define the energy density gained by the system in the superconducting state as (1/2)u,H2. The electrons in a Cooper pair are separated on a length scale of 5, however, and so the correlations cannot be fully achieved until a distance roughly S from the boundary of the superconductor. There is thus an energy per unit area, (1/2)uH25, that is lost because of the presence of the boundary. Now consider the effects of the applied magnetic field on this system. It costs the superconductor energy to maintain the Meissner effect, B=0, in its bulk; in fact the energy density required is(1/2)] H2. However, since the field can penetrate the perconductor a distance roughly A, the system need not expend an energy per unit area of(1/2)HHato screen over this volume. To summarize, more than a distance s from the boundary, the energy of the material is lowered(because it is superconducting), and more than a distance A from the boundary the energy of the material is raised(to shield the applied field) Now,ifλ<ξ,the of superconducting material greater than A from the boundary but less than s will higher in energy than that in the bulk of the material. Thus, the surface energy of the boundary is positive and so costs the total system some energy. This class of superconductors is known as type I Most elemental uperconductors, such as aluminum, tin, and lead, are type I. In addition to having A< s, type I superconductors are generally characterized by low critical temperatures(5 K)and critical fields(-005 T). Typical type I superconductors and their properties are listed in Table 53.2. TABLE 53.2 Material Parameters for Type I conductors* Material T (K) A, (nm) E(nm) A, (mev) HoH(mT) 00090 123.0 "The penetration depth A, is given at zero temperature, as are the coher- ence length Eo, the thermodynamic critical field Hee, and the energy gap a Source: R ]. Donnelly, " Cryogenics,in Physics Vade mecum, H L Ander- on, Ed, New York: American Institute of Physics, 1981. with permission. e 2000 by CRC Press LLC
© 2000 by CRC Press LLC allows the possibility of a device whose output voltage is a function of a static magnetic field. If two weak links are connected in parallel, the lumped version of Faraday’s law gives the voltage across the second weak link as n2 = n1 + (dF/dt), where F is the total flux threading the loop between the links. Substituting Eq. (53.15), integrating with respect to time, and again setting the integration constant to zero yields (53.19) showing that the spatial change in the phase of the macroscopic wavefunction is proportional to the local magnetic flux. The structure described is known as a superconducting quantum interference device (SQUID) and can be used as a highly sensitive magnetometer by biasing it with current and measuring the resulting voltage as a function of magnetic flux. From this discussion, it is apparent that a duality exists in how fields interact with the macroscopic phase: electric fields are coupled to its rate of change in time and magnetic fields are coupled to its rate of change in space. 53.4 Types of Superconductors The macroscopic quantum nature of superconductivity also affects the general electromagnetic properties previously discussed. This is most clearly illustrated by the interplay of the characteristic lengths j, representing the scale of quantum correlations, and l, representing the scale of electromagnetic screening. Consider the scenario where a magnetic field, H, is applied parallel to the surface of a semi-infinite superconductor. The correlations of the electrons in the superconductor must lower the overall energy of the system or else the material would not be superconducting in the first place. Because the critical magnetic field Hc destroys all the correlations, it is convenient to define the energy density gained by the system in the superconducting state as (1/2)moHc 2 . The electrons in a Cooper pair are separated on a length scale of j, however, and so the correlations cannot be fully achieved until a distance roughly j from the boundary of the superconductor. There is thus an energy per unit area, (1/2)moHc 2 j, that is lost because of the presence of the boundary. Now consider the effects of the applied magnetic field on this system. It costs the superconductor energy to maintain the Meissner effect, B = 0, in its bulk; in fact the energy density required is (1/2)moH2 . However, since the field can penetrate the superconductor a distance roughly l, the system need not expend an energy per unit area of (1/2)moH2l to screen over this volume. To summarize, more than a distance j from the boundary, the energy of the material is lowered (because it is superconducting), and more than a distance l from the boundary the energy of the material is raised (to shield the applied field). Now, if l < j, the region of superconducting material greater than l from the boundary but less than j will be higher in energy than that in the bulk of the material. Thus, the surface energy of the boundary is positive and so costs the total system some energy. This class of superconductors is known as type I. Most elemental superconductors, such as aluminum, tin, and lead, are type I. In addition to having l < j, type I superconductors are generally characterized by low critical temperatures (;5 K) and critical fields (;0.05 T). Typical type I superconductors and their properties are listed in Table 53.2. TABLE 53.2 Material Parameters for Type I Superconductors* Material Tc (K) lo (nm) jo (nm) Do (meV) m0Hco (mT) Al 1.18 50 1600 0.18 110.5 In 3.41 65 360 0.54 123.0 Sn 3.72 50 230 0.59 130.5 Pb 7.20 40 90 1.35 180.0 Nb 9.25 85 40 1.50 198.0 *The penetration depth lo is given at zero temperature, as are the coherence length jo, the thermodynamic critical field Hco, and the energy gap Do. Source: R.J. Donnelly, “Cryogenics,” in Physics Vade Mecum, H.L. Anderson, Ed., New York: American Institute of Physics, 1981. With permission. f f p 2 1 - = (2 F F) o
Conversely, if A>5, the surface er Bergy associated with the boundary is negative and lowers the total system energy. It is therefore thermodynamically favorable for a normal-superconducting interface to form inside these type II materials. Consequently, this class of superconductors does not exhibit the simple Meissner effect as do type I materials. Instead, there are now two critical fields: for applied fields below the lower critical field, Hal a type II superconductor is in the Meissner state, and for applied fields greater than the upper critical field, H2, superconductivity is destroyed. The three critical field are related to each other by H.-HeHe2 In the range H <H< H2, a type II superconductor is said to be in the vortex state because now the applied field can enter the bulk superconductor. Because flux exists in the material, however, the superconductivity is destroyed locally, creating normal regions. Recall that for type II materials the boundary between the normal and superconducting regions lowers the overall energy of the system. Therefore, the flux in the superconductor creates as many normal-superconducting interfaces as possible without violating quantum criteria. The net result is that flux enters a type II superconductor in quantized bundles of magnitude p, known as vortices or fluxons(the former name derives from the fact that current flows around each quantized bundle in the same manner as a fluid vortex circulates around a drain). The central portion of a vortex, known as the core, is a normal region with an approximate radius of E. If a defect-free superconductor is placed in a magnetic field, he individual vortices, whose cores essentially follow the local average field lines, form an ordered triangular array, or flux lattice. As the applied field is raised beyond H,( where the first vortex enters the superconductor), the distance between adjacent vortex cores decreases to maintain the appropriate flux density in the material. Finally, the upper critical field is reached when the normal cores overlap and the material is no longer superconducting. Indeed, a precise calculation of Ha using the phenomenological theory developed by vitaly H 2 which verifies our simple picture. The values of typical type II material parameters are listed in Tables 53.3 and Type II superconductors are of great technical importance because typical H, values are at least an order of magnitude greater than the typical H values of type I materials. It is therefore possible to use type II materials to make high-field magnet wire. Unfortunately, when current is applied to the wire, there is a Lorentz-like force on the vortices, causing them to move. Because the moving vortices carry flux, their motion creates a static voltage drop along the superconducting wire by Faradays law. As a result, the wire no longer has a zero dc TABLE 53.3 Material Parameters for Conventional Type II Superconductors* Material T(k) AG(o)(nm) Ea(o)(nm) (mev) Hge(t) PbIn 0.2 Pb-B 0.5 NE 1.5 13.0 16.0 PbMo ss 15.0 2.4 15.0 06 2 4523333 23.0 16.0 20.0 Nb Sn 18.0 3.4 23.0 Nb_ Ge " The values are only representative because the parameters for alloys and depend on how the material is fabricated. The penetration depth Ag(O)is oefficient of the Ginzburg-Landau temperature dependence as AG)=2g(o)(I kewise for the coherence length where SG(T)=EG(o)(1-77T)-. The uppe Source: R.J. Donnelly, " Cryogenics, in Physics Vade mecum, H L. Anderson, Ed, New York: American Institute of Physics, 1981. With permission. c2000 by CRC Press LLC
© 2000 by CRC Press LLC Conversely, if l > j, the surface energy associated with the boundary is negative and lowers the total system energy. It is therefore thermodynamically favorable for a normal–superconducting interface to form inside these type II materials. Consequently, this class of superconductors does not exhibit the simple Meissner effect as do type I materials. Instead, there are now two critical fields: for applied fields below the lower critical field, Hc1, a type II superconductor is in the Meissner state, and for applied fields greater than the upper critical field, Hc2, superconductivity is destroyed. The three critical field are related to each other by Hc ª . In the range Hc 1 < H < Hc2, a type II superconductor is said to be in the vortex state because now the applied field can enter the bulk superconductor. Because flux exists in the material, however, the superconductivity is destroyed locally, creating normal regions. Recall that for type II materials the boundary between the normal and superconducting regions lowers the overall energy of the system. Therefore, the flux in the superconductor creates as many normal–superconducting interfaces as possible without violating quantum criteria. The net result is that flux enters a type II superconductor in quantized bundles of magnitude Fo known as vortices or fluxons (the former name derives from the fact that current flows around each quantized bundle in the same manner as a fluid vortex circulates around a drain). The central portion of a vortex, known as the core, is a normal region with an approximate radius of j. If a defect-free superconductor is placed in a magnetic field, the individual vortices, whose cores essentially follow the local average field lines, form an ordered triangular array, or flux lattice. As the applied field is raised beyond Hc 1 (where the first vortex enters the superconductor), the distance between adjacent vortex cores decreases to maintain the appropriate flux density in the material. Finally, the upper critical field is reached when the normal cores overlap and the material is no longer superconducting. Indeed, a precise calculation of Hc2 using the phenomenological theory developed by Vitaly Ginzburg and Lev Landau yields (53.20) which verifies our simple picture. The values of typical type II material parameters are listed in Tables 53.3 and 53.4. Type II superconductors are of great technical importance because typical Hc2 values are at least an order of magnitude greater than the typical Hc values of type I materials. It is therefore possible to use type II materials to make high-field magnet wire. Unfortunately, when current is applied to the wire, there is a Lorentz-like force on the vortices, causing them to move. Because the moving vortices carry flux, their motion creates a static voltage drop along the superconducting wire by Faraday’s law. As a result, the wire no longer has a zero dc TABLE 53.3 Material Parameters for Conventional Type II Superconductors* Material Tc (K) lGL(0) (nm) jGL(0) (nm) Do (meV) m0Hc2,o (T) Pb-In 7.0 150 30 1.2 0.2 Pb-Bi 8.3 200 20 1.7 0.5 Nb-Ti 9.5 300 4 1.5 13.0 Nb-N 16.0 200 5 2.4 15.0 PbMo6 S8 15.0 200 2 2.4 60.0 V3Ga 15.0 90 2–3 2.3 23.0 V3Si 16.0 60 3 2.3 20.0 Nb3Sn 18.0 65 3 3.4 23.0 Nb3Ge 23.0 90 3 3.7 38.0 *The values are only representative because the parameters for alloys and compounds depend on how the material is fabricated. The penetration depth lGL(0) is given as the coefficient of the Ginzburg–Landau temperature dependence as lGL(T) = lGL(0)(1 – T/Tc)–1/2; likewise for the coherence length where jGL(T) = jGL(0)(1 – T/Tc)–1/2. The upper critical field Hc2,o is given at zero temperature as well as the energy gap Do . Source: R.J. Donnelly, “Cryogenics,” in Physics Vade Mecum, H.L. Anderson, Ed., New York: American Institute of Physics, 1981. With permission. Hc1Hc2 Hc o o 2 2 2 = m F p x