《MIMO多进多出多天线》课程教学资源（文献资料）Massive MIMO for Next Generation Wireless Systems

ACCEPTED FROM OPEN CALL Massive MIMO for Next Generation Wireless Systems Erik G. Larsson, ISY, Linkoping University, Sweden Ove Edfors and Fredrik Tufvesson, Lund University, Sweden Thomas L. Marzetta, Bell Labs, Alcatel-Lucent, United States ABSTRACT up on our earlier exposition [1]， with a focus on the developments in the last three years; most Multi-user MIMO offers big advantages over particularly, energy efficiency, exploitation of conventional point-to-point MIMO: it works excess degrees of freedom, time-division duplex with cheap single-antenna terminals, a rich scat- (TDD)calibration, techniques to combat pilot tering environment is not required, and resource contamination, and entirely new channel mea- allocation is simplified because every active ter- surements. minal utilizes all of the time-frequency bins. With massive MIMO, we think of systems However, multi-user MIMO, as originally envi- that use antenna arrays with a few hundred sioned, with roughly equal numbers of service antennas simultaneously serving many tens of antennas and terminals and frequency-division terminals in the same time-frequency resource. duplex operation, is not a scalable technology. The basic premise behind massive MIMO is to Massive MIMO (also known as large-scale reap all the benefits of conventional MIMO, but antenna systems, very large MIMO, hyper on a much greater scale. Overall, massive MIMO MIMO, full-dimension MIMO, and ARGOS) is an enabler for the development of future makes a clean break with current practice broadband (fixed and mobile)networks, which through the use of a large excess of service will be energy-efficient, secure, and robust, and antennas over active terminals and time-division will use the spectrum efficiently. As such, it is an duplex operation. Extra antennas help by focus- enabler for the future digital society infra- ing energy into ever smaller regions of space to structure that will connect the Internet of people bring huge improvements in throughput and and Internet of Things with clouds and other radiated energy efficiency. Other benefits of network infrastructure. Many different configu- massive MIMO include extensive use of inexpen- rations and deployment scenarios for the actual sive low-power components, reduced latency, antenna arrays used by a massive MIMO system simplification of the MAC layer, and robustness can be envisioned (Fig. 1). Each antenna unit against intentional jamming. The anticipated would be small and active, preferably fed via an throughput depends on the propagation environ- optical or electric digital bus. ment providing asymptotically orthogonal chan- Massive MIMO relies on spatial multiplexing, nels to the terminals, but so far experiments which in turn relies on the base station having have not disclosed any limitations in this regard. good enough channel knowledge, on both the While massive MIMO renders many traditional uplink and the downlink. On the uplink, this is research problems irrelevant, it uncovers entirely easy to accomplish by having the terminals send new problems that urgently need attention: the pilots, based on which the base station estimates challenge of making many low-cost low-precision the channel responses to each of the terminals. components that work effectively together, The downlink is more difficult. In conventional acquisition and synchronization for newly joined MIMO systems such as the Long Term Evolu- terminals, the exploitation of extra degrees of tion(LTE)standard, the base station sends out freedom provided by the excess of service anten- pilot waveforms, based on which the terminals nas, reducing internal power consumption to estimate the channel responses, quantize the achieve total energy efficiency reductions, and thus obtained estimates, and feed them back to finding new deployment scenarios. This article the base station. This will not be feasible in mas- presents an overview of the massive MIMO con- sive MIMO systems, at least not when operating cept and contemporary research on the topic. in a high-mobility environment, for two reasons. First, optimal downlink pilots should be mutually GOING LARGE: MASSIVE MIMO orthogonal between the antennas. This means that the amount of time-frequency resources Massive multiple-input multiple-output(MIMO) needed for downlink pilots scales with the num- is an emerging technology that scales up MIMO ber of antennas, so a massive MIMO system by possibly orders of magnitude compared to the would require up to 100 times more such current state of the art. In this article, we follow resources than a conventional system. Second, 186 0163-6804/14/$25.0002014IEEE IEEE Communications Magazine.February 2014

186 0163-6804/14/$25.00 © 2014 IEEE IEEE Communications Magazine • February 2014 GOING LARGE: MASSIVE MIMO Massive multiple-input multiple-output (MIMO) is an emerging technology that scales up MIMO by possibly orders of magnitude compared to the current state of the art. In this article, we follow up on our earlier exposition [1], with a focus on the developments in the last three years; most particularly, energy efficiency, exploitation of excess degrees of freedom, time-division duplex (TDD) calibration, techniques to combat pilot contamination, and entirely new channel mea￾surements. With massive MIMO, we think of systems that use antenna arrays with a few hundred antennas simultaneously serving many tens of terminals in the same time-frequency resource. The basic premise behind massive MIMO is to reap all the benefits of conventional MIMO, but on a much greater scale. Overall, massive MIMO is an enabler for the development of future broadband (fixed and mobile) networks, which will be energy-efficient, secure, and robust, and will use the spectrum efficiently. As such, it is an enabler for the future digital society infra￾structure that will connect the Internet of people and Internet of Things with clouds and other network infrastructure. Many different configu￾rations and deployment scenarios for the actual antenna arrays used by a massive MIMO system can be envisioned (Fig. 1). Each antenna unit would be small and active, preferably fed via an optical or electric digital bus. Massive MIMO relies on spatial multiplexing, which in turn relies on the base station having good enough channel knowledge, on both the uplink and the downlink. On the uplink, this is easy to accomplish by having the terminals send pilots, based on which the base station estimates the channel responses to each of the terminals. The downlink is more difficult. In conventional MIMO systems such as the Long Term Evolu￾tion (LTE) standard, the base station sends out pilot waveforms, based on which the terminals estimate the channel responses, quantize the thus obtained estimates, and feed them back to the base station. This will not be feasible in mas￾sive MIMO systems, at least not when operating in a high-mobility environment, for two reasons. First, optimal downlink pilots should be mutually orthogonal between the antennas. This means that the amount of time-frequency resources needed for downlink pilots scales with the num￾ber of antennas, so a massive MIMO system would require up to 100 times more such resources than a conventional system. Second, ABSTRACT Multi-user MIMO offers big advantages over conventional point-to-point MIMO: it works with cheap single-antenna terminals, a rich scat￾tering environment is not required, and resource allocation is simplified because every active ter￾minal utilizes all of the time-frequency bins. However, multi-user MIMO, as originally envi￾sioned, with roughly equal numbers of service antennas and terminals and frequency-division duplex operation, is not a scalable technology. Massive MIMO (also known as large-scale antenna systems, very large MIMO, hyper MIMO, full-dimension MIMO, and ARGOS) makes a clean break with current practice through the use of a large excess of service antennas over active terminals and time-division duplex operation. Extra antennas help by focus￾ing energy into ever smaller regions of space to bring huge improvements in throughput and radiated energy efficiency. Other benefits of massive MIMO include extensive use of inexpen￾sive low-power components, reduced latency, simplification of the MAC layer, and robustness against intentional jamming. The anticipated throughput depends on the propagation environ￾ment providing asymptotically orthogonal chan￾nels to the terminals, but so far experiments have not disclosed any limitations in this regard. While massive MIMO renders many traditional research problems irrelevant, it uncovers entirely new problems that urgently need attention: the challenge of making many low-cost low-precision components that work effectively together, acquisition and synchronization for newly joined terminals, the exploitation of extra degrees of freedom provided by the excess of service anten￾nas, reducing internal power consumption to achieve total energy efficiency reductions, and finding new deployment scenarios. This article presents an overview of the massive MIMO con￾cept and contemporary research on the topic. ACCEPTED FROM OPEN CALL Erik G. Larsson, ISY, Linköping University, Sweden Ove Edfors and Fredrik Tufvesson, Lund University, Sweden Thomas L. Marzetta, Bell Labs, Alcatel-Lucent, United States Massive MIMO for Next Generation Wireless Systems EDFORS_LAYOUT.qxp_Layout 1/30/14 1:08 PM Page 186

agRachce While the concepts of massive MIMO have ts have been performed [4,5. THE POTENTIAL OF MASSIVE MIMO ease the capacity1 onfigurations and deployment scenarios fo imormercandimaneoi that it ribute MIMO s region in space (Fig2).The underlying 6 d t ly ortho when the hat all w The on in Fig. n an info ndwidt nel sta rmati MRC oise-limited informa z) In about dimension( of the total num ber of bits (sum MR an ing in the "green spen affe ting the o ctions tend to be ov off for t are se one single antenn rving a sing 100 nal (purple inal reg that divi 1g1 ximum ratio nd the scale of the ctiveness atio c .con r6400 IEEE Communications Magazine February 2014 187

IEEE Communications Magazine • February 2014 187 the number of channel responses each terminal must estimate is also proportional to the number of base station antennas. Hence, the uplink resources needed to inform the base station of the channel responses would be up to 100 times larger than in conventional systems. Generally, the solution is to operate in TDD mode, and rely on reciprocity between the uplink and down￾link channels, although frequency-division duplext (FDD) operation may be possible in cer￾tain cases [2]. While the concepts of massive MIMO have been mostly theoretical so far, stimulating much research particularly in random matrix theory and related mathematics, basic testbeds are becoming available [3], and initial channel mea￾surements have been performed [4, 5]. THE POTENTIAL OF MASSIVE MIMO Massive MIMO technology relies on phase￾coherent but computationally very simple pro￾cessing of signals from all the antennas at the base station. Some specific benefits of a massive MU-MIMO system are: •Massive MIMO can increase the capacity 10 times or more and simultaneously improve the radiated energy efficiency on the order of 100 times. The capacity increase results from the aggressive spatial multiplexing used in massive MIMO. The fundamental principle that makes the dramatic increase in energy efficiency possible is that with a large number of antennas, energy can be focused with extreme sharpness into small regions in space (Fig. 2). The underlying physics is coherent superposition of wavefronts. By appropriately shaping the signals sent out by the antennas, the base station can make sure that all wavefronts collectively emitted by all antennas add up constructively at the locations of the intended terminals, but destructively (ran￾domly) almost everywhere else. Interference between terminals can be suppressed even fur￾ther by using, for example, zero-forcing (ZF). This, however, may come at the cost of more transmitted power, as illustrated in Fig. 2. More quantitatively, Fig. 3 (from [6]) depicts the fundamental trade-off between energy effi￾ciency in terms of the total number of bits (sum rate) transmitted per Joule per terminal receiv￾ing service of energy spent, and spectral efficiency in terms of total number of bits (sum rate) trans￾mitted per unit of radio spectrum consumed. The figure illustrates the relation for the uplink, from the terminals to the base station (the down￾link performance is similar). The figure shows the trade-off for three cases: • A reference system with one single antenna serving a single terminal (purple) • A system with 100 antennas serving a single terminal using conventional beamforming (green) • A massive MIMO system with 100 antennas simultaneously serving multiple (about 40 here) terminals (red, using maximum ratio combining, and blue, using ZF). The attractiveness of maximum ratio combin￾ing (MRC) compared with ZF is not only its computational simplicity — multiplication of the received signals by the conjugate channel responses — but also that it can be performed in a distributed fashion, independently at each antenna unit. While ZF also works fairly well for a conventional or moderately sized MIMO sys￾tem, MRC generally does not. The reason that MRC works so well for massive MIMO is that the channel responses associated with different terminals tend to be nearly orthogonal when the number of base station antennas is large. The prediction in Fig. 3 is based on an infor￾mation-theoretic analysis that takes into account intracell interference, as well as the bandwidth and energy cost of using pilots to acquire chan￾nel state information in a high-mobility environ￾ment [6]. With the MRC receiver, we operate in the nearly noise-limited regime of information theory. This means providing each terminal with a rate of about 1 b/complex dimension (1 b/s/Hz). In a massive MIMO system, when using MRC and operating in the “green” regime (i.e., scaling down the power as much as possible without seriously affecting the overall spectral efficiency), multiuser interference and effects from hardware imperfections tend to be over￾whelmed by the thermal noise. The reason that the overall spectral efficiency still can be 10 times higher than in conventional MIMO is that many tens of terminals are served simultaneous￾ly, in the same time-frequency resource. When operating in the 1 b/dimension/terminal regime, there is also some evidence that intersymbol interference can be treated as additional thermal noise [7], hence offering a way of disposing with orthogonal frequency-division multiplexing (OFDM) as a means of combatting intersymbol interference. To understand the scale of the capacity gains massive MIMO offers, consider an array consist￾ing of 6400 omnidirectional antennas (total form factor 6400 × (l/2)2  40 m2) transmitting with a total power of 120 W (i.e., each antenna radiat￾Figure 1. Some possible antenna configurations and deployment scenarios for a massive MIMO base station. Distributed Cylindrical Rectangular Linear EDFORS_LAYOUT.qxp_Layout 1/30/14 1:08 PM Page 187

range,and th havc broadband 000 homc ltiplexing ficient accura or the uplink)andt om servic e.We use a capacity Mas ssive MIMO can be built with inexpen- which mation error beamforming We use optimal max-min power systems are replaced by hundreds of low-cost 5 10 s15 Area with 400 random scatterers -15 8007 ide bea 10 Area with 400 random scatt ncoming wide bea 800 r (*and four o r users nearby（ IEEE Communications MagazineFebruary 2014

188 IEEE Communications Magazine • February 2014 ing about 20 mW) over a 20 MHz bandwidth in the personal communications services (PCS) band (1900 MHz). The array serves 1000 fixed terminals randomly distributed in a disk of radius 6 km centered on the array, each terminal hav￾ing an 8 dB gain antenna. The height of the antenna array is 30 m, and the height of the ter￾minals is 5 m. Using the Hata-COST231 model, we find that the path loss is 127 dB at 1 km range, and the range-decay exponent is 3.52. There is also log-normal shadow fading with 8 dB standard deviation. The receivers have a 9 dB noise figure. One-quarter of the time is spent on transmission of uplink pilots for TDD chan￾nel estimation, and it is assumed that the chan￾nel is substantially constant over intervals of 164 ms in order to estimate the channel gains with sufficient accuracy. Downlink data is transmitted via maximum ratio transmission (MRT) beam￾forming combined with power control, where the 5 percent of terminals with the worst channels are excluded from service. We use a capacity lower bound from [8] extended to accommodate slow fading, near/far effects and power control, which accounts for receiver noise, channel esti￾mation errors, the overhead of pilot transmis￾sion, and the imperfections of MRT beamforming. We use optimal max-min power control, which confers an equal signal-to-inter￾ference-plus-noise ratio on each of the 950 ter￾minals and therefore equal throughput. Numerical averaging over random terminal loca￾tions and the shadow fading shows that 95 per￾cent of the terminals will receive a throughput of 21.2 Mb/s/terminal. Overall, the array in this example will offer the 1000 terminals a total downlink throughput of 20 Gb/s, resulting in a sum-spectral efficiency of 1000 b/s/Hz. This would be enough, for example, to provide 20 Mb/s broadband service to each of 1000 homes. The max-min power control provides equal ser￾vice simultaneously to 950 terminals. Other types of power control combined with time-division multiplexing could accommodate heterogeneous traffic demands of a larger set of terminals. The MRC receiver (for the uplink) and its counterpart MRT precoding (for the downlink) are also known as matched filtering (MF) in the literature. • Massive MIMO can be built with inexpen￾sive, low-power components. Massive MIMO is a game changing technolo￾gy with regard to theory, systems, and implemen￾tation. With massive MIMO, expensive ultra-linear 50 W amplifiers used in conventional systems are replaced by hundreds of low-cost Figure 2. Relative field strength around a target terminal in a scattering environment of size 800 l × 800 l when the base station is placed 1600 l to the left. Average field strengths are calculated over 10,000 random placements of 400 scatterers when two different linear precoders are used: a) MRT precoders; b) ZF precoders. Left: pseudo-color plots of average field strengths, with target user posi￾tions at the center () and four other users nearby (). Right: average field strengths as surface plots, allowing an alternate view of the spatial focusing. Area with 400 random scatterers ≤ Incoming narrow beam 400 λ 800 λ 800 λ Narrow beam Wide beam Area with 400 random scatterers 100-element λ/2-spaced linear array 1600 λ a) MRT precoding (dB) [dB] -10 400 λ -15 -5 0 5 800 λ ≤ Incoming wide beam 400 λ (dB) [dB] -10 400 λ -15 -5 0 5 800 λ 100-element λ/2-spaced linear array 1600 λ b) ZF precoding -10 ≤ −15 -5 0 5 -10 ≤ 15 -5 0 5 EDFORS_LAYOUT.qxp_Layout 1/30/14 1:08 PM Page 188

a 103 stations today are reduce the conon (r/qy(r/q) 102 10 etemim sngentena 20304050 7080 Spectral efficiency(b//Hz) aea e-friendlysigna rage ratio9 o er ef nalty in terms of incr nt) am Fig.4.With Th signal s Ra r s samp the the spots where tiple paths i ee p em to :0 t is this fad nis possible is that th e ha n chan entl ut affe cting what the ac sm the muliple acces ng. nd of large numbers,the te eases the robustnes tions is ag orldwid ma-made of civilian grid is ay onus efore th nt nt that ant due to the d concerns regard. ng and douar IEEE Communications Magazine February 2014 189

IEEE Communications Magazine • February 2014 189 amplifiers with output power in the milli-Watt range. The contrast to classical array designs, which use few antennas fed from high-power amplifiers, is significant. Several expensive and bulky items, such as large coaxial cables, can be eliminated altogether. (The typical coaxial cables used for tower-mounted base stations today are more than 4 cm in diameter!) Massive MIMO reduces the constraints on accuracy and linearity of each individual amplifi￾er and RF chain. All that matters is their com￾bined action. In a way, massive MIMO relies on the law of large numbers to make sure that noise, fading, and hardware imperfections aver￾age out when signals from a large number of antennas are combined in the air. The same property that makes massive MIMO resilient against fading also makes the technology extremely robust to failure of one or a few of the antenna unit(s). A massive MIMO system has a large surplus of degrees of freedom. For example, with 200 antennas serving 20 terminals, 180 degrees of freedom are unused. These degrees of freedom can be used for hardware-friendly signal shap￾ing. In particular, each antenna can transmit sig￾nals with very small peak-to-average ratio [9] or even constant envelope [10] at a very modest penalty in terms of increased total radiated power. Such (near-constant) envelope signaling facilitates the use of extremely cheap and power￾efficient RF amplifiers. The techniques in [9, 10] must not be confused with conventional beamforming techniques or equal-magnitude￾weight beamforming techniques. This distinction is explained in Fig. 4. With (near) constant￾envelope multiuser precoding, no beams are formed, and the signals emitted by each antenna are not formed by weighing a symbol. Rather, a wavefield is created such that when this wave￾field is sampled at the spots where the terminals are located, the terminals see precisely the sig￾nals we want them to see. The fundamental property of the massive MIMO channel that makes this possible is that the channel has a large nullspace: almost anything can be put into this nullspace without affecting what the termi￾nals see. In particular, components can be put into this nullspace that make the transmitted waveforms satisfy the desired envelope con￾straints. Notwithstanding, the effective channels between the base station and each of the termi￾nals can take any signal constellation as input and do not require the use of phase shift keying (PSK) modulation. The drastically improved energy efficiency enables massive MIMO systems to operate with a total output RF power two orders of magni￾tude less than with current technology. This mat￾ters, because the energy consumption of cellular base stations is a growing concern worldwide. In addition, base stations that consume many orders of magnitude less power could be powered by wind or solar, and hence easily deployed where no electricity grid is available. As a bonus, the total emitted power can be dramatically cut, and therefore the base station will generate substan￾tially less electromagnetic interference. This is important due to the increased concerns regard￾ing electromagnetic exposure. •Massive MIMO enables a significant reduc￾tion of latency on the air interface. The performance of wireless communications systems is normally limited by fading. Fading can render the received signal strength very small at certain times. This happens when the signal sent from a base station travels through multiple paths before it reaches the terminal, and the waves resulting from these multiple paths inter￾fere destructively. It is this fading that makes it hard to build low-latency wireless links. If the terminal is trapped in a fading dip, it has to wait until the propagation channel has sufficiently changed until any data can be received. Massive MIMO relies on the law of large numbers and beamforming in order to avoid fading dips, so fading no longer limits latency. •Massive MIMO simplifies the multiple access layer. Due to the law of large numbers, the chan￾nel hardens so that frequency domain schedul￾ing no longer pays off. With OFDM, each subcarrier in a massive MIMO system will have substantially the same channel gain. Each ter￾minal can be given the whole bandwidth, which renders most of the physical layer control sig￾naling redundant. •Massive MIMO increases the robustness against both unintended man-made interference and intentional jamming. Intentional jamming of civilian wireless sys￾tems is a growing concern and a serious cyber￾security threat that seems to be little known to the public. Simple jammers can be bought off the Internet for a few hundred dollars, and equipment that used to be military-grade can be put together using off-the-shelf software radio￾based platforms for a few thousand dollars. Figure 3. Half the power — twice the force (from [6]): Improving uplink spec￾tral efficiency 10 times and simultaneously increasing the radiated power effi- ciency 100 times with massive MIMO technology, using extremely simple signal processing, taking into account the energy and bandwidth costs of obtaining channel state information. Spectral efficiency (b/s/Hz) 0 10 100 10–1 Relative energy efficiency (b /J)/(b/J) 101 102 103 104 20 30 40 50 60 70 80 Single antenna, single terminal 90 100 antennas, single terminal 100 antennas, multiple terminals, MRC processing 100 antennas, multiple terminals, ZF processing EDFORS_LAYOUT.qxp_Layout 1/30/14 1:08 PM Page 189

Combine em UK : ⊕ eioM ing co rasted with p namic range eeeg罗 hguihpied 0 police officers s of mass s is to use multip atch within the chain o ission the nas e to tally dim can be reated as a reference LIMITING FACTORS OF MASSIVE MIMO en the uplink and CHANNEL RECIPROCITY eamfo noidsoc Time-division duplexing operation relies on reduction ing)a PILOT CONTAMINATION pilot diided bythe channcl delay

190 IEEE Communications Magazine • February 2014 Numerous recent incidents, especially in public safety applications, illustrate the magnitude of the problem. During the EU summit in Gothen￾burg, Sweden, in 2001, demonstrators used a jammer located in a nearby apartment, and dur￾ing critical phases of riots, the chief commander could not reach any of the 700 police officers engaged [11]. Due to the scarcity of bandwidth, spreading information over frequency just is not feasible, so the only way of improving robustness of wireless communications is to use multiple antennas. Massive MIMO offers many excess degrees of freedom that can be used to cancel signals from intentional jammers. If massive MIMO is implemented using uplink pilots for channel estimation, smart jammers could cause harmful interference with modest transmission power. However, more clever implementations using joint channel estimation and decoding should be able to substantially diminish that problem. LIMITING FACTORS OF MASSIVE MIMO CHANNEL RECIPROCITY Time-division duplexing operation relies on channel reciprocity. There appears to be a rea￾sonable consensus that the propagation channel itself is essentially reciprocal unless the propaga￾tion is affected by materials with strange mag￾netic properties. However, the hardware chains in the base station and terminal transceivers may not be reciprocal between the uplink and the downlink. Calibration of the hardware chains does not seem to constitute a serious problem, and there are calibration-based solutions that have already been tested to some extent in prac￾tice [3, 12]. Specifically, [3] treats reciprocity cal￾ibration for a 64-antenna system in some detail and claims a successful experimental implemen￾tation. Note that calibration of the terminal uplink and downlink chains is not required in order to obtain the full beamforming gains of massive MIMO: if the base station equipment is properly calibrated, the array will indeed transmit a coherent beam to the terminal. (There will still be some mismatch within the receiver chain of the terminal, but this can be handled by trans￾mitting pilots through the beam to the terminal; the overhead for these supplementary pilots is very small.) Absolute calibration within the array is not required. Instead, as proposed in [3], one of the antennas can be treated as a reference, and signals can be traded between the reference antenna and each of the other antennas to derive a compensation factor for that antenna. It may be possible to entirely forgo reciprocity calibra￾tion within the array; for example if the maxi￾mum phase difference between the uplink and downlink chains were less than 60˚, coherent beamforming would still occur (at least with MRT beamforming), albeit with a possible 3 dB reduction in gain. PILOT CONTAMINATION Ideally, every terminal in a massive MIMO sys￾tem is assigned an orthogonal uplink pilot sequence. However, the maximum number of orthogonal pilot sequences that can exist is upper-bounded by the duration of the coherence interval divided by the channel delay spread. In Figure 4. Conventional MIMO beamforming contrasted with per-antenna constant envelope transmission in massive MIMO. Left: con￾ventional beamforming, where the signal emitted by each antenna has a large dynamic range. Right: per-antenna constant envelope transmission, where each antenna sends out a signal with a constant envelope. ejφ1 ejφm ejφM α1 Per-antenna varying envelope Combined varying α envelope uk m uK fc u1 αM Linear encoder α = W (H)u Per-antenna constant envelope Combined varying u envelope k uK fc u1 Phase-only encoder φ = f (u,H) EDFORS_LAYOUT.qxp_Layout 1/30/14 1:08 PM Page 190

RADIO PROPAGATION AND ORTHOGONALITY OF NNEL RESPONSES Massive MIMO (and Massive MIMO (and especially MRC/MRT le propagation m nt on property of the radi environment called favorable propaga chan ments hav Thi tion.Simply stated or usin able rs rom tha r arrays.The mos on m ans that the on cha Similar inter istics mayals ase station to d erent temminals an s of the two asurements repor this a it d t clas P MIMO 3. er.Be te lim with rely at di nt has b recently 15].at elem 时0 r ent po e d d.One po lots (b are al a): te the use o base sta rent term twork [16].Cur ii cly.co arg ariz dcircularatl y tion.The nd) ted re d (id) as pilo stud s in the Lund U rements wer ra ultiplicity of cel The GHz ally. ng drical array.the R k Lun dinate was useTh and the sen ination pre ng requ value spread ng al powe ed s IEEE Communications Magazine February 2014 191

IEEE Communications Magazine • February 2014 191 [13], for a typical operating scenario, the maxi￾mum number of orthogonal pilot sequences in a 1 ms coherence interval is estimated to be about 200. It is easy to exhaust the available supply of orthogonal pilot sequences in a multicellular sys￾tem. The effect of reusing pilots from one cell to another and the associated negative conse￾quences is termed pilot contamination. More specifically, when the service array correlates its received pilot signal with the pilot sequence associated with a particular terminal, it actual￾ly obtains a channel estimate that is contami￾nated by a linear combination of channels with other terminals that share the same pilot sequence. Downlink beamforming based on the contaminated channel estimate results in interference directed at those terminals that share the same pilot sequence. Similar inter￾ference is associated with uplink transmissions of data. This directed interference grows with the number of service antennas at the same rate as the desired signal [13]. Even partially correlated pilot sequences result in directed interference. Pilot contamination as a basic phenomenon is not really specific to massive MIMO, but its effect on massive MIMO appears to be much more profound than in classical MIMO [13, 14]. In [13] it was argued that pilot contamination constitutes an ultimate limit on performance when the number of antennas is increased with￾out bound, at least with receivers that rely on pilot-based channel estimation. While this argu￾ment has been contested recently [15], at least under some specific assumptions on the power control used, it appears likely that pilot contami￾nation must be dealt with in some way. This can be done in several ways: •The allocation of pilot waveforms can be optimized. One possibility is to use a less aggres￾sive frequency reuse factor for the pilots (but not necessarily for the payload data); say, 3 or 7. This pushes mutually contaminating cells farther apart. It is also possible to coordinate the use of pilots or adaptively allocate pilot sequences to the different terminals in the network [16]. Cur￾rently, the optimal strategy is unknown. •Clever channel estimation algorithms [15], or even blind techniques that circumvent the use of pilots altogether [17], may mitigate or elimi￾nate the effects of pilot contamination. The most promising direction seems to be blind techniques that jointly estimate the channels and the pay￾load data. •New precoding techniques that take into account the network structure, such as pilot contamination precoding [18], can utilize coop￾erative transmission over a multiplicity of cells — outside of the beamforming operation — to nullify, at least partially, the directed interfer￾ence that results from pilot contamination. Unlike coordinated beamforming over multiple cells, which requires estimates of the actual channels between the terminals and the service arrays of the contaminating cells, pilot contam￾ination precoding requires only the corre￾sponding slow-fading coefficients. Practical pilot contamination precoding remains to be developed. RADIO PROPAGATION AND ORTHOGONALITY OF CHANNEL RESPONSES Massive MIMO (and especially MRC/MRT pro￾cessing) relies to a large extent on a property of the radio environment called favorable propaga￾tion. Simply stated, favorable propagation means that the propagation channel responses from the base station to different terminals are sufficient￾ly different. To study the behavior of massive MIMO systems, channel measurements have to be performed using realistic antenna arrays. This is so because the channel behavior using large arrays differs from that usually experienced using conventional smaller arrays. The most important differences are that: • There might be large-scale fading over the array. • The small-scale signal statistics may also change over the array. Of course, this is also true for physically smaller arrays with directional antenna elements pointing in various directions. Figure 5 shows pictures of the two massive MIMO arrays used for the measurements report￾ed in this article. On the left is a compact circu￾lar massive MIMO array with 128 antenna ports. This array consists of 16 dual-polarized patch antenna elements arranged in a circle, with 4 such circles stacked on top of each other. Besides having the advantage of being compact, this array also provides the possibility to resolve scat￾terers at different elevations, but it suffers from worse resolution in azimuth due to its limited aperture. To the right is a physically large linear (virtual) array, where a single omnidirectional antenna element is moved to 128 different posi￾tions in an otherwise static environment to emu￾late a real array with the same dimensions. One way of quantifying how different the channel responses to different terminals are is to look at the spread between the smallest and largest singular values of the matrix that contains the channel responses. Figure 6 illustrates this for a case with 4 user terminals and a base sta￾tion having 4, 32, and 128 antenna ports, respec￾tively, configured as either a physically large single-polarized linear array or a compact dual￾polarized circular array. More specifically, the figure shows the cumulative density function (CDF) of the difference between the smallest and largest singular values for the different mea￾sured (narrowband) frequency points in the dif￾ferent cases. As a reference, we also show simulated results for ideal independent identical￾ly distributed (i.i.d.) channel matrices, often used in theoretical studies. The measurements were performed outdoors in the Lund University cam￾pus area. The center frequency was 2.6 GHz and the measurement bandwidth 50 MHz. When using the cylindrical array, the RUSK Lund channel sounder was employed, while a network analyzer was used for the synthetic linear array measurements. The first results from the cam￾paign were presented in [4]. For the 4-element array, the median of the singular value spread is about 23–18 dB. This number is a measure of the fading margin, the additional power that has to be used in order to serve all users with a reasonable received signal Massive MIMO (and especially MRC/MRT processing) relies to a large extent on a property of the radio environment called favorable propaga￾tion. Simply stated, favorable propaga￾tion means that the propagation channel responses from the base station to dif￾ferent terminals are sufficiently different. EDFORS_LAYOUT.qxp_Layout 1/30/14 1:08 PM Page 191

igure 5.Massive MIMO antenna arays used for the measurements the spread As can be seen in Fig.7.the sum rate tee cae the nur of antennas at the of th sun m petween users at a distance of about 40m ay in the form of shadd no h f the direction.Also,due to the fac m what more co butstill linear.pre 03 nel coeff. rate lower as the num na 40 for a very tri Thi hile the other ions are als

192 IEEE Communications Magazine • February 2014 power. With the massive linear array, the spread is less than 3 dB. In addition, note that none of the curves has any substantial tail. This means that the probability of seeing a singular value spread larger than 3 dB anywhere over the mea￾sured bandwidth is essentially negligible. To further illustrate the influence of different numbers of antenna elements at the base station and antenna configuration, we plot in Fig. 7 the sum rate for 4 closely spaced users (less than 2 m between users at a distance of about 40 m from the base station) in a non line-of-sight (NLOS) scenario when using MRT as precoding. The transmit power is normalized so that on average, the interference-free signal-to-noise￾ratio at the terminals is 10 dB. As can be seen in Fig. 7, the sum rate approaches that of the theoretical interference￾free case as the number of antennas at the base station increases. The shaded areas in red (for the linear array) and blue (for the circular array) shows the 90 percent confidence intervals of the sum rates for the different narrowband frequency realizations. As before, the variance of the sum rate decreases as the number of antennas increas￾es, but slowly for the measured channels. The slow decrease can, at least partially, be attributed to the shadow fading occurring across the arrays: for the linear array in the form of shadowing by external objects along the array, and for the cylindical array in the form of shadowing caused by directive antenna elements pointing in the wrong direction. The performance of the physi￾cally large array approaches that of the theoreti￾cal i.i.d. case when the number of antennas grows large. The compact circular array has inferior performance compared to the linear array due to its smaller aperture — it cannot resolve the scat￾terers as well as the physically large array — and its directive antenna elements sometimes point￾ing in the wrong direction. Also, due to the fact that most of the scatterers are seen at the same horizontal angle, the possibility to resolve scatters at different elevations gives only marginal contri￾butions to the sum rate in this scenario. It should be mentioned here that when using somewhat more complex, but still linear, pre￾coding methods such as ZF or minimum mean square error, the convergence to the i.i.d. chan￾nel performance is faster and the variance of the sum rate lower as the number of base station antennas is increased; see [4] for further details. Also, another aspect worth mentioning is that for a very tricky propagation scenario, such as closely spaced users in line-of-sight conditions, it seems that the large array is able to separate the users to a reasonable extent using the different spatial signatures the users have at the base sta￾tion due to the enhanced spatial resolution. This would not be possible with conventional MIMO. These conclusions are also in line with the obser￾vations in [5], where another outdoor measure￾ment campaign is described and analyzed. Figure 5. Massive MIMO antenna arrays used for the measurements. Figure 6. CDF of the singular value spread for MIMO systems with 4 terminals and three different numbers of base station antennas: 4, 32, and 128. The the￾oretical i.i.d. channel is shown as a reference, while the other two cases are measured channels with linear and cylindrical array structures at the base sta￾tion. Note that the curve for the linear array coincides with that of the i.i.d. channel for four base stations. Singular value spread (dB) 0 10 0.1 0 CDF 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 20 30 40 50 i.i.d. channel coeff. Linear array Cylindrical array # base station antennas: 4 32 128 EDFORS_LAYOUT.qxp_Layout 1/30/14 1:08 PM Page 192

Interference free13.8 b/s/Hz 14 12 ble to 至10 6 MASSIVE MIMO:A GOLD MINE OF RESEARCH PROBLEMS Cylindrical array 20 40 6080100 120 ing: anddistihuteoherentgalp5ocess Number of base station antennas Figure 7.Achieved downlink sum rates nearly lin Fig.3).Much researh ed edicated,hardware for the baseband sig addi alog-to-dig hanne dels th ail. ut they must c This is I likely to m tha e,ir th nel st and 1. Powe ers with types of the use of per-ar ation:TDD wil h a larg city calib itcrant nd what is the b na. Wha tuch the d in hardware componen wh a sym Pilot contamination:It is likcly that pilot con around the pl mass e MIMO than on traditic ecei the mos Non-Csro Bcfore a up data rates.Ho ver in practice,the total channel res ns the cos har oI space-t EEE Communications Magazine February 2014 193

IEEE Communications Magazine • February 2014 193 Overall, there is compelling evidence that the assumptions on favorable propagation underpin￾ning massive MIMO are substantially valid in practice. Depending on the exact configuration of the large array and the precoding algorithms used, the convergence toward the ideal perfor￾mance may be faster or slower as the number of antennas is increased. However, with about 10 times more base station antennas than the num￾ber of users, it seems that it is possible to get stable performance not far from the theoretically ideal performance also under what are normally considered very difficult propagation conditions. MASSIVE MIMO: A GOLD MINE OF RESEARCH PROBLEMS While massive MIMO renders many traditional problems in communication theory less relevant, it uncovers entirely new problems that need research. Fast and distributed coherent signal process￾ing: Massive MIMO arrays generate vast amounts of baseband data that must be pro￾cessed in real time. This processing will have to be simple, and simple means linear or nearly lin￾ear. Fundamentally, this is good in many cases (Fig. 3). Much research needs be invested in the design of optimized algorithms and their imple￾mentation. On the downlink, there is enormous potential for ingenious precoding schemes. Some examples of recent work in this direction include [19]. The challenge of low-cost hardware: Building hundreds of RF chains, up/down converters, analog-to-digital (A/D)-digital-to-analog (D/A) converters, and so forth, will require economy of scale in manufacturing comparable to what we have seen for mobile handsets. Hardware impairments: Massive MIMO relies on the law of large numbers to average out noise, fading and to some extent, interference. In reality, massive MIMO must be built with low-cost components. This is likely to mean that hardware imperfections are larger: in particular, phase noise and I/Q imbalance. Low-cost and power-efficient A/D converters yield higher lev￾els of quantization noise. Power amplifiers with very relaxed linearity requirements will necessi￾tate the use of per-antenna low peak-to-average signaling, which, as already noted, is feasible with a large excess of transmitter antennas. With low-cost phase locked loops or even free-running oscillators at each antenna, phase noise may become a limiting factor. However, what ulti￾mately matters is how much the phase will drift between the point in time when a pilot symbol is received and the point in time when a data sym￾bol is received at each antenna. There is great potential to get around the phase noise problem by design of smart transmission physical layer schemes and receiver algorithms. Internal power consumption: Massive MIMO offers the potential to reduce the radiated power 1000 times and at the same time drastically scale up data rates. However, in practice, the total power consumed must be considered, including the cost of baseband signal processing. Much research must be invested in highly parallel, per￾haps dedicated, hardware for the baseband sig￾nal processing. Channel characterization: There are addi￾tional properties of the channel to consider when using massive MIMO instead of conven￾tional MIMO. To facilitate a realistic perfor￾mance assessment of massive MIMO systems, it is necessary to have channel models that reflect the true behavior of the radio channel (i.e., the propagation channel including effects of realistic antenna arrangements). It is also important to develop more sophisticated analytical channel models. Such models need not necessarily be correct in every fine detail, but they must cap￾ture the essential behavior of the channel. For example, in conventional MIMO the Kronecker model is widely used to model channel correla￾tion. This model is not an exact representation of reality, but provides a useful model for certain types of analysis despite its limitations. A similar way of thinking could probably be adopted for massive MIMO channel modeling. Cost of reciprocity calibration: TDD will require reciprocity calibration. How often must this be done, and what is the best way of doing it? What is the cost, in terms of time- and fre￾quency resources needed to do the calibration, and in terms of additional hardware components needed? Pilot contamination: It is likely that pilot con￾tamination imposes much more severe limita￾tions on massive MIMO than on traditional MIMO systems. We have discussed some of the issues in detail and outlined some of the most relevant research directions earlier. Non-CSI@TX operation: Before a link has been established with a terminal, the base sta￾tion has no way of knowing the channel response to the terminal. This means that no array beam￾forming gain can be harnessed. In this case, probably some form of space-time block coding Figure 7. Achieved downlink sum rates using MRT precoding, with 4 single￾antenna terminals and between 4 and 128 base station antennas. Number of base station antennas 0 20 2 0 Sum rate (b/s/Hz) 4 6 8 10 12 14 16 40 60 80 100 120 i.i.d. channel coefficient Linear array Cylindrical array Average and 90 percent conf. interval Interference free → 13.8 b/s/Hz EDFORS_LAYOUT.qxp_Layout 1/30/14 1:08 PM Page 193

is ninal has heen Continued testbed the ta tion can learn th true spatial lexing ent is MU-MIMO b forming mode,reaping the to both prove the mass MIMO co dcPtwi both prov poten lly new issues that urgently need massive MiMO concept with eve that p larger numbers of not require vard con CONCLUSIONS AND OUTLOOK antennas and discov er potentially new at w d be used so y fo cel ular techno issues that urgenth need researd ations tha ency,robustness,and reli us.rather than at oth the bas ation and the TE it obile unit sic thing that 15t hardwar nd relation to sm ell and ver units tha coherently to ethe otiva sim nolo for exa ntial rib ssing al and synchr dep small cells. esulting in oth ad ademia and ind entirely new research pro mine The authors would like to thank Xiang Gao good en nough channel state info tion (CSD to e antennas and clonke m parts of this work REFERENCE te I.Rusek at same ti ributed 2 30. n203 ns and w izing Ma and on 2012 d 14]X.Gao cteristics fo I5 develop ent: While massiv pro A Rice univ 20 pp. asibility of the ma H.Yang 64 testbed shows that IDD nas.In n 013 On iti 110 P.Stemp. gaar IEEE Communications MagazineFebruary 201

194 IEEE Communications Magazine • February 2014 is optimal. Once the terminal has been contact￾ed and sent a pilot, the base station can learn the channel response and operate in coherent MU-MIMO beamforming mode, reaping the power gains offered by having a very large array. New deployment scenarios: It is considered extraordinarily difficult to introduce a radical new wireless standard. One possibility is to intro￾duce dedicated applications of massive MIMO technology that do not require backward com￾patibility. For example, as discussed earlier, in rural areas, a billboard-sized array could provide 20 Mb/s service to each of 1000 homes using special equipment that would be used solely for this application. Alternatively, a massive array could provide the backhaul for base stations that serve small cells in a densely populated area. Thus, rather than thinking of massive MIMO as a competitor to LTE, it can be an enabler for something that was just never before considered possible with wireless technology. System studies and relation to small-cell and heterogeneous network solutions: The driving motivation of massive MIMO is to simultaneous￾ly and drastically increase data rates and overall energy efficiency. Other potential ways of reach￾ing this goal are network densification by the deployment of small cells, resulting in a hetero￾geneous architecture, or coordination of the transmission of multiple individual base stations. From a purely fundamental perspective, the ulti￾mately limiting factor of the performance of any wireless network appears to be the availability of good enough channel state information (CSI) to facilitate phase-coherent processing at multiple antennas or multiple access points [20]. Consid￾ering factors like mobility, Doppler shifts, phase noise, and clock synchronization, acquiring high￾quality CSI seems to be easier with a collocated massive array than in a system where the anten￾nas are distributed over a large geographical area. But at the same time, a distributed array or small cell solution may offer substantial path loss gains and would also provide some diversity against shadow fading. The deployment costs of a massive MIMO array and a distributed or small cell system are also likely to be very differ￾ent. Hence, both communication-theoretic and techno-economic studies are needed to conclu￾sively determine which approach is superior. However, it is likely that the winning solution will comprise a combination of all available tech￾nologies. Prototype development: While massive MIMO is in its infancy, basic prototyping work on various aspects of the technology is going on in different parts of the world. The Argos testbed [3] was developed at Rice University in coopera￾tion with Alcatel-Lucent, and shows the basic feasibility of the massive MIMO concept using 64 coherently operating antennas. In particular, the testbed shows that TDD operation relying on channel reciprocity is possible. One of the virtues of the Argos testbed in particular is that it is entirely modular and scalable, and built around commercially available hardware (the WARP platform). Other test systems around the world have also demonstrated the basic feasibili￾ty of scaling up the number of antennas. The Ngara testbed in Australia [21] uses a 32-ele￾ment base station array to serve up to 18 users simultaneously with true spatial multiplexing. Continued testbed development is highly desired to both prove the massive MIMO concept with even larger numbers of antennas and discover potentially new issues that urgently need research. CONCLUSIONS AND OUTLOOK In this article we have highlighted the large potential of massive MIMO systems as a key enabling technology for future beyond fourth generation (4G) cellular systems. The technology offers huge advantages in terms of energy effi￾ciency, spectral efficiency, robustness, and relia￾bility. It allows for the use of low-cost hardware at both the base station and the mobile unit side. At the base station the use of expensive and powerful, but power-inefficient, hardware is replaced by massive use of parallel low-cost low￾power units that operate coherently together. There are still challenges ahead to realize the full potential of the technology, for example, computational complexity, realization of dis￾tributed processing algorithms, and synchroniza￾tion of the antenna units. This gives researchers in both academia and industry a gold mine of entirely new research problems to tackle. ACKNOWLEDGMENTS The authors would like to thank Xiang Gao, doctoral student at Lund University, for her analysis of the channel measurements presented in Fig. 6 and Fig. 7, and the Swedish organiza￾tions ELLIIT, VR, and SSF for their funding of parts of this work. REFERENCES [1] F. Rusek et al., “Scaling Up MIMO: Opportunities and Challenges with Very Large Arrays,” IEEE Sig. Proc. Mag., vol. 30, Jan. 2013, pp. 40–60. [2] J. Nam et al., “Joint Spatial Division and Multiplexing: Realizing Massive MIMO Gains with Limited Channel State Information,” 46th Annual Conf. Information Sci￾ences and Systems, 2012. [3] C. Shepard et al., “Argos: Practical Many-Antenna Base Stations,” ACM Int’l. Conf. Mobile Computing and Net￾working, Istanbul, Turkey, Aug. 2012. [4] X. Gao et al., “Measured Propagation Characteristics for Very-Large MIMO at 2.6 GHz,” Proc. 46th Annual Asilo￾mar Conf. Signals, Systems, and Computers, Pacific Grove, CA, Nov. 2012. [5] J. Hoydis et al., “Channel Measurements for Large Antenna Arrays,” IEEE Int’l. Symp. Wireless Commun. Systems, Paris, France, Aug. 2012. [6] H. Q. Ngo, E. G. Larsson, and T. L. Marzetta, “Energy and Spectral Efficiency of Very Large Multiuser MIMO Systems,” IEEE Trans. Commun., vol. 61, Apr. 2013, pp. 1436–49. [7] A. Pitarokoilis, S. K. Mohammed, and E. G. Larsson, “On the Optimality of Single-Carrier Transmission in Large￾Scale Antenna Systems,” IEEE Wireless Commun. Lett., vol. 1, no. 4, Aug. 2012, pp. 276–79. [8] H. Yang and T. L. Marzetta, “Performance of Conjugate and Zero-Forcing Beamforming in Large-Scale Antenna Sys￾tems,” IEEE JSAC, vol. 31, no. 2, Feb. 2013, pp. 172–79. [9] C. Studer and E. G. Larsson, “PAR-Aware Large-Scale Multi-User MIMO-OFDM Downlink,” IEEE JSAC, vol. 31, Feb. 2013, pp. 303–13. [10] S. K. Mohammed and E. G. Larsson, “Per-Antenna Constant Envelope Precoding for Large Multi-User MIMO Systems,” IEEE Trans. Commun., vol. 61, Mar. 2013, pp. 1059–71. [11] P. Stenumgaard et al., “An Early-Warning Service for Emerging Communication Problems in Security and Safety Applications,” IEEE Commun. Mag., vol. 51, no. 5, Mar. 2013, pp. 186–92. Continued testbed development is highly desired to both prove the massive MIMO concept with even larger numbers of antennas and discov￾er potentially new issues that urgently need research. EDFORS_LAYOUT.qxp_Layout 1/30/14 1:08 PM Page 194

25 BIOGRAPHIES 01 here aresti challe nges a reaize the T EE Signal 3股e example.when it erandoeAod Approach to Channe 1 no.2.Feb 2013.pp.26 gatio d processing complexity buted proce and his Ph.D.in 2000 from "Pilot Cor ng algonthms,an an associate prof th synchronization o the antenna units 21j He he was e MIMC 1981 ASS rec IEEE Communications Magazine February 2014 195

IEEE Communications Magazine • February 2014 195 [12] F. Kaltenberger et al., “Relative Channel Reciprocity Calibration in MIMO/TDD Systems,” Proc. Future Net￾work and Mobile Summit, 2010, 2010. [13] T. L. Marzetta, “Noncooperative Cellular Wireless with Unlimited Numbers of Base Station Antennas,” IEEE Trans. Wireless Commun., vol. 9, no. 11, Nov. 2010, pp. 3590–600. [14] J. Hoydis, S. ten Brink, and M. Debbah, “Massive MIMO in the UL/DL of Cellular Networks: How Many Antennas Do We Need?,” IEEE JSAC, vol. 31, no. 2, Feb. 2013, pp. 160–71. [15] R. Müller, M. Vehkaperä, and L. Cottatellucci, “Blind Pilot Decontamination,” Proc. ITG Wksp. Smart Anten￾nas, Stuttgart, Mar. 2013. [16] H. Yin et al., “A Coordinated Approach to Channel Estimation in Large-Scale Multiple-Antenna Systems,” IEEE JSAC, vol. 31, no. 2, Feb. 2013, pp. 264–73. [17] H. Q. Ngo and E. G. Larsson, “EVD-Based Channel Esti￾mations for Multicell Multiuser MIMO with Very Large Antenna Arrays,” Proc. IEEE Int’l. Conf. Acoustics, Speed and Sig. Proc., Mar. 2012. [18] A. Ashikhmin and T. L. Marzetta, “Pilot Contamination Precoding in Multi-Cell Large Scale Antenna Systems,” IEEE Int’l. Symp. Information Theory, Cambridge, MA, July 2012. [19] J. Zhang, X. Yuan, and L. Ping, “Hermitian Precoding for Distributed MIMO Systems with Individual Channel State Information,” IEEE JSAC, vol. 31, no. 2, Feb. 2013, pp. 241–50. [20] A. Lozano, R.W. Heath Jr, and J. G. Andrews, “Funda￾mental Limits of Cooperation,” IEEE Trans. Info. Theory, vol. 59, Sept. 2013, pp. 5213–26. [21] H. Suzuki et al., “Highly Spectrally Efficient Ngara Rural Wireless Broadband ACCESS Demonstrator,” Proc. IEEE Int’l. Symp. Commun. and Information Technolo￾gies, Oct. 2012. BIOGRAPHIES ERIK G. LARSSON is a professor and head of the Division for Communication Systems in the Department of Electrical Engineering at Linköping University, Sweden. He has pub￾lished some 100 journal papers on signal processing and communications, and is a co-author of the textbook Space￾Time Block Coding for Wireless Communications. He is an Associate Editor for IEEE Transactions on Communications, and he received the IEEE Signal Processing Magazine Best Column Award 2012. OVE EDFORS is a professor of radio systems in the Depart￾ment of Electrical and Information Technology, Lund Uni￾versity, Sweden. His research interests include statistical signal processing and low-complexity algorithms with applications in wireless communications. In the context of massive MIMO, his research focus is on how realistic prop￾agation characteristics influence system performance and baseband processing complexity. FREDRIK TUFVESSON received his Ph.D. in 2000 from Lund Uni￾versity. After almost two years at a startup company, Fiber￾less Society, he is now an associate professor in the Department of Electrical and Information Technology, Lund University. His main research interests are channel mea￾surements and modeling for wireless communication, including channels for both MIMO and UWB systems. Besides these, he also works on distributed antenna sys￾tems and radio-based positioning. THOMAS L. MARZETTA [F’03] received his Ph.D. in electrical engineering from the Massachusetts Institute of Technolo￾gy. He joined Bell Laboratories in 1995. Within the former Mathematical Sciences Research Center he was director of the Communications and Statistical Sciences Department. He was an early proponent of massive MIMO, which can provide huge improvements in wireless spectral efficiency and energy efficiency over 4G technologies. He received the 1981 ASSP Paper Award and received the 2013 IEEE Guglielmo Marconi Best Paper Award. There are still challenges ahead to realize the full potential of the technology, for example, when it comes to computational complexity, realization of distributed process￾ing algorithms, and synchronization of the antenna units. EDFORS_LAYOUT.qxp_Layout 1/30/14 1:08 PM Page 195