A Wideband CMOS Variable-Gain Low Noise Amplifier with Novel Attenuator Tao Cheng,Tao Yang,Xin Wang,Zhangwen Tang ASIC System State Key Laboratory,Fudan University,Shanghai 201203,China Email:zwtang@fudan.edu.cn Abstract suitable for TV tuner whose gain range is-22 ~20 dB This paper presents a wideband variable-gain low noise with 2 dB/step and covering both VHF and UHF band.It amplifier (VGLNA)which is used in mobile TV tuner has two different inputs,one for VHF and the other for covering VHF band (50 to 250 MHz)and UHF band UHF,to isolate each other.Figure I shows the overall (470 to 860MHz).The proposed VGLNA includes three topology of the wideband VGLNA.When only S3 is on, gain paths for different input signal strengths:high gain -22 dB ~-6 dB is achieved by a novel attenuator (ATT) path,attenuation path,medium gain path.The high gain for VHF or UHF:when only S0 and S2 are on,-4 dB path is realized by an active AC feedback LNA,whose 14 dB can be realized by combining one ATT and one DC current is set by a constant-Gm biasing;the novel active AC feedback LNA which constitute medium gain attenuator used in attenuation path has constant input path(MGP),and 14 dB~20 dB for VHF or UHF can be impedance which guarantees a good S11 with the variety acquired by the other active AC feedback LNA when of gain;the medium gain path is the combination of one only SI or S4 is on which is high gain path(HGP).The active AC feedback LNA and one attenuator.The chip is capacitor Co in figure 1 is used to insulate the DC signal implemented in 0.18 um CMOS process and achieves a of LNA for MGP.All switches are controlled by a simple gain range over 42 dB (2dB/step),a minimum noise digital control unit. figure of 2 dB at maximum gain,an IIP3 of 27.9 dBm at LNA for UHF HGP UHF high gain path minimum gain.The die consumes 8 mA from 1.8 V urfinD supply voltage at maximum gain. ATT for UHF Medium gain path 1.Introduction Although a lot of efforts have been devoted to the research of TV tuners and important achievements have LNA for MGP been made [1][2],designing a distinguished TV tuner Attenuation path supporting multi-standard multi-band is still full of challenges.As the first active stage of TV tuner,VGLNA ATT for VHF LNA for VHF HGP plays a vital role in the overall performance. A mobile TV tuner may receive a signal level as high vrfinD as-10 dBm or as low as-110 dBm.Low noise figure and VHF high gain path high gain are needed for low level input,which is critical Figure 1.The overall topology of the VGLNA especially for LNA.As the input level increasing,the corresponding gain should be reduced so that the 2.1 High gain path(HGP) subsequent stages remain sufficiently linear with the Figure 2 shows the circuit topology in high gain path large input signal.An attenuator is often used with even The active AC feedback LNA presented in this paper higher input level. separates DC signal from its signal paths so the feedback A novel attenuator with high linearity,small gain step is just an AC feedback achieved by Ri,Ci and Rr,Cr, and better noise performance is proposed in this paper. and DC current can be set independently.A constant-Gm The high gain path is realized by an active feedback biasing circuit [4]is used to bias the amplifying MOSs LNA which is similar to the one in [31.but the feedback MAI ~MA4 and the cascode MOSs MC1 MC4.The is only AC coupling.The gain step in the high gain path inductor L is employed to extend output bandwidth is realized by changing the gm of amplifying MOS.In the which is not needed in VHF high gain path.So VHF and next section,the detail implementation of the proposed UHF high gain path have a little difference. VGLNA will be described.The measurement results will be given at last. A.Input matching and gain analysis To implement a gain step of 2 dB,four switches are Circuit realization used to change the gm of amplifying MOS.When all The target is to design a CMOS wideband VGLNA switches are connected up,maximum gain is achieved. 978-1-4673-6417-1/13/$31.00C2013IEEE 797
A Wideband CMOS Variable-Gain Low Noise Amplifier with Novel Attenuator Tao Cheng, Tao Yang, Xin Wang, Zhangwen Tang* ASIC & System State Key Laboratory, Fudan University, Shanghai 201203, China * Email: zwtang@fudan.edu.cn Abstract This paper presents a wideband variable-gain low noise amplifier (VGLNA) which is used in mobile TV tuner covering VHF band (50 to 250 MHz) and UHF band (470 to 860MHz). The proposed VGLNA includes three gain paths for different input signal strengths: high gain path, attenuation path, medium gain path. The high gain path is realized by an active AC feedback LNA, whose DC current is set by a constant-Gm biasing; the novel attenuator used in attenuation path has constant input impedance which guarantees a good S11 with the variety of gain; the medium gain path is the combination of one active AC feedback LNA and one attenuator. The chip is implemented in 0.18 ȝm CMOS process and achieves a gain range over 42 dB (2dB/step), a minimum noise figure of 2 dB at maximum gain, an IIP3 of 27.9 dBm at minimum gain. The die consumes 8 mA from 1.8 V supply voltage at maximum gain. 1. Introduction Although a lot of efforts have been devoted to the research of TV tuners and important achievements have been made [1] [2], designing a distinguished TV tuner supporting multi-standard multi-band is still full of challenges. As the first active stage of TV tuner, VGLNA plays a vital role in the overall performance. A mobile TV tuner may receive a signal level as high as -10 dBm or as low as -110 dBm. Low noise figure and high gain are needed for low level input, which is critical especially for LNA. As the input level increasing, the corresponding gain should be reduced so that the subsequent stages remain sufficiently linear with the large input signal. An attenuator is often used with even higher input level. A novel attenuator with high linearity, small gain step and better noise performance is proposed in this paper. The high gain path is realized by an active feedback LNA which is similar to the one in [3], but the feedback is only AC coupling. The gain step in the high gain path is realized by changing the gm of amplifying MOS. In the next section, the detail implementation of the proposed VGLNA will be described. The measurement results will be given at last. 2. Circuit realization The target is to design a CMOS wideband VGLNA suitable for TV tuner whose gain range is -22 ~ 20 dB with 2 dB/step and covering both VHF and UHF band. It has two different inputs, one for VHF and the other for UHF, to isolate each other. Figure 1 shows the overall topology of the wideband VGLNA. When only S3 is on, -22 dB ~ -6 dB is achieved by a novel attenuator (ATT) for VHF or UHF; when only S0 and S2 are on, -4 dB ~ 14 dB can be realized by combining one ATT and one active AC feedback LNA which constitute medium gain path (MGP), and 14 dB ~ 20 dB for VHF or UHF can be acquired by the other active AC feedback LNA when only S1 or S4 is on which is high gain path (HGP). The capacitor C0 in figure 1 is used to insulate the DC signal of LNA for MGP. All switches are controlled by a simple digital control unit. Figure 1. The overall topology of the VGLNA 2.1 High gain path (HGP) Figure 2 shows the circuit topology in high gain path. The active AC feedback LNA presented in this paper separates DC signal from its signal paths so the feedback is just an AC feedback achieved by R1, C1 and RF, CF, and DC current can be set independently. A constant-Gm biasing circuit [4] is used to bias the amplifying MOSs MA1 ~ MA4 and the cascode MOSs MC1 ~ MC4. The inductor L is employed to extend output bandwidth which is not needed in VHF high gain path. So VHF and UHF high gain path have a little difference. A. Input matching and gain analysis To implement a gain step of 2 dB, four switches are used to change the gm of amplifying MOS. When all switches are connected up, maximum gain is achieved. 978-1-4673-6417-1/13/$31.00 ©2013 IEEE 797
S2 S3 S4 2 C C Vin Constant-Gm Biasing GND Active AC Feedback LNA Figure 2.The circuit topology in high gain path Minimum gain can be obtained when only SI is substitute equation(2)into (3) connected up.A simplified circuit as shown in figure 3 can be used to analysis the performance of the circuit 28maR (4) when the parasitic resistance of L is neglected. So changing gmA can directly change the gain.With the constant-Gm biasing,equation(4)can be further derived (5) o Vout where a is scale factor of the current mirror.The above expression is immune to the variations of process. R voltage and temperature(PVT).It is just impacted by the proportion of two resistances,which can be relatively accurate by taking good care of layout. MR Rs B.Noise and nonlinearity consideration GND Since the small signal AC gain has been calculated Figure 3.Simplified circuit for analysis every noise source can be equivalent to the output in a similar way by simply calculating the transform function The input impedance Rin can be calculated as from the noise source to the output.If the flicker noise is Rin 1+gmRe not considered,the noise figure(NF)is [3] (1) (1+gmAR)8mE WF=1+ 1A2+A R where gmA is the transconductance of the device MA,and 8mA·Rs1+A R1+A)2 gmF is the transconductance of the device MF.If input is matched,then Rin =Rs,so the input matching can be R 1 4 2+A (6) achieved when 1+A R(1+A)小8A·RA 1+A 1+gmF Rg =(1+8mARL)gmE Rs (2) R It is obvious that the value of Re should follow the +a‘8msR1- R(1+A) variety of gmA i.e.the variety of gain when the value of where y is a coefficient which equals to 2/3 for long gmF is constant.To achieve a good input matching channel transistors and may be replaced by a larger value performance with the variety of gain,R is chosen to be for submicron MOSFETs.Av equals to gmA RL.Since increasing as gain increase. Ay>>1,above expression becomes Ignoring the second order effect,the small signal AC gain can be expressed as NF≈1+A。+BgR (7) '=-，l+8sR8aR 8mA·R3 1+(1+gmARL)8mE Rs +gme Rr (3) If a long channel MOS is used for the device MB and its overdrive voltage is set as large as possible,the When the condition of input matching is applied,i.e. contribution of the bias device MB can also be neglected. 798
Figure 2. The circuit topology in high gain path Minimum gain can be obtained when only S1 is connected up. A simplified circuit as shown in figure 3 can be used to analysis the performance of the circuit when the parasitic resistance of L is neglected. Figure 3. Simplified circuit for analysis The input impedance Rin can be calculated as mF F in mA L mF 1 1 g R R g R g (1) where gmA is the transconductance of the device MA, and gmF is the transconductance of the device MF. If input is matched, then Rin = RS, so the input matching can be achieved when mF F mA L mF S 1 1 g R gRgR . (2) It is obvious that the value of RF should follow the variety of gmA i.e. the variety of gain when the value of gmF is constant. To achieve a good input matching performance with the variety of gain, RF is chosen to be increasing as gain increase. Ignoring the second order effect, the small signal AC gain can be expressed as out mF F mA L in mA L mF S mF F 1 1 1 ( ) ( ) v gRg R v g RgR gR . (3) When the condition of input matching is applied, i.e. substitute equation (2) into (3) out mA L in 1 2 v g R v . (4) So changing gmA can directly change the gain. With the constant-Gm biasing, equation (4) can be further derived out L in B 1 1 § · ¨ ¸ © ¹ v R Į v R K (5) where Į is scale factor of the current mirror. The above expression is immune to the variations of process, voltage and temperature (PVT). It is just impacted by the proportion of two resistances, which can be relatively accurate by taking good care of layout. B. Noise and nonlinearity consideration Since the small signal AC gain has been calculated, every noise source can be equivalent to the output in a similar way by simply calculating the transform function from the noise source to the output. If the flicker noise is not considered, the noise figure (NF) is [3] 2 A F v 2 mA S v 2 F F v v S v mA S v 2 F B mB S S v 2 1 1 1 1 2 1 11 1 1 1 S v v ( ) ( ) ( ) § · ¨ ¸ © ¹ ª º § · « » ¨ ¸ ¬ ¼ © ¹ ª º « » ¬ ¼ Ȗ A R NF gR A R A Ȗ R A A R A g RA A R Ȗ g R R A (6) where Ȗ is a coefficient which equals to 2/3 for long channel transistors and may be replaced by a larger value for submicron MOSFETs. AV equals to gmA RL. Since AV >> 1, above expression becomes A B mB S mA 1 S | Ȗ NF Ȗ g R g R . (7) If a long channel MOS is used for the device MB and its overdrive voltage is set as large as possible, the contribution of the bias device MB can also be neglected. 798
So the main contribution of noise figure is from the noise introduces more output noise,the proposed one has of amplifying MOSs.A larger gmA obviously yields a better noise performance.As the minimum value of lower noise figure and also pays the price for larger resistance is R/8,reducing the parasitic resistance of the parasitic capacitance lowering the noise figure at high switch is critical to ensure the accurate gain.Setting the frequency.Since the target frequency is much larger than size of S4,S5 and S6 inverse proportional to their the 1/f corner,excluding 1/f noise will not influence the relevant value of resistance can achieve better result too much. performance.The switch in [5]is selected for S1,S2,S3, As the output signal is a large signal compared to the and S7,S8 and S9,they have better linearity input signal.When a large signal is applied to the gate of performance and good isolation characteristic when they the device MF,the dominate contribution of nonlinearity are off.Those switches should also have their ratios. will come from the nonlinearity of the device MF which degrades substantially IIP3 value.Additionally,the Table 1.Switch control and the corresponding gain feedback can combine the second-order distortion with S2 S3 S5 S6 S7 S8 S9 S10 Gain the fundamentals of the output signal,generating (dB) third-order distortion at the output,which further 6 worsens the IIP3 value.Decreasing gain,increasing the -8 overdrive voltage of the device MF and increasing the -10 value of Rr will improve IIP3 [3],but there are always .12 trade-offs among noise.IIP3.voltage headroom.input -14 matching,etc. -16 2.2 Proposed attenuator(ATT) 20 DR照 R4 S3 -22 “l”denotes on,blank denotes off. 0.16RS8 3021RS9 2.3 Medium gain path (MGP) ATT LNA for MGP GND 0.63R S10 -6 dB,-12 dB,-18 dB 14~20 dB,with 2 dB step GND Figure 5.The block diagram of MGP Figure 4.The schematic of attenuator The block diagram of MGP is shown in figure 5.Just Figure 4 shows the schematic of attenuator,in which R equals to 50 ohms.The proposed attenuator has three gain modes are used in the attenuator,and the LNA employed here is similar to the LNA used in HGP.As constant input impedance over all different gain modes, VHF and UHF share the MGP.the bandwidth of MGP is which grantees good input matching.For example,when different from the HGP so the value of the inductor L only S1.S4,S10 and S7 are on,then and the resistance R.Another difference that should be R(0.16R+0.21R+0.63R) =-6dB.(8) noted is that the LNA for MGP do not need input Vin R 2 matching anymore,which gives more freedom to R|(0.16R+0.21R+0.63R)+ 2 optimize the noise and linearity performances.So the In the meanwhile value of Re is also different. Since 14 dB have two different implementation ways R=号+R0.16R+0.21R+0.63R)=R=R.(9 which can be used to choose noise optimization or To acquire a step of 2 dB,S8 and S9 are introduced.If linearity optimization.For instance,choosing HGP to realize a 14 dB will have a better noise figure than S7 is off and S8 is on in above situation,taking choosing MGP.but the latter have better linearity advantage of(8),then performance.8 dB gain and 2 dB gain have similar 10.16R+0.63R ≈-8dB.(10) situations. 20.16R+0.21R+0.63R -10 dB can obtain by setting S9 on.Table 1 shows the 3.Measurement results detail control of switches and the corresponding gain. A prototype of this VGLNA which is fabricated in The conventional R-2R topology in [5]has larger 0.18um CMOS process occupies 870 um x 760 um area output impedance compared to the proposed one when including pads.Figure 6 shows the die micrograph of the the input is matched.Since larger output impedance VGLNA and performance summary.Figure 7 shows the 799
So the main contribution of noise figure is from the noise of amplifying MOSs. A larger gmA obviously yields a lower noise figure and also pays the price for larger parasitic capacitance lowering the noise figure at high frequency. Since the target frequency is much larger than the 1/f corner, excluding 1/f noise will not influence the result too much. As the output signal is a large signal compared to the input signal. When a large signal is applied to the gate of the device MF, the dominate contribution of nonlinearity will come from the nonlinearity of the device MF which degrades substantially IIP3 value. Additionally, the feedback can combine the second-order distortion with the fundamentals of the output signal, generating third-order distortion at the output, which further worsens the IIP3 value. Decreasing gain, increasing the overdrive voltage of the device MF and increasing the value of RF will improve IIP3 [3], but there are always trade-offs among noise, IIP3, voltage headroom, input matching, etc. 2.2 Proposed attenuator (ATT) Figure 4. The schematic of attenuator Figure 4 shows the schematic of attenuator, in which R equals to 50 ohms. The proposed attenuator has constant input impedance over all different gain modes, which grantees good input matching. For example, when only S1, S4, S10 and S7 are on, then out in 0.16 0.21 0.63 1 6 dB 2 0.16 0.21 0.63 2 v RRRR v R RRRR . (8) In the meanwhile in S 0 16 0 21 0 63 2 ... R R R R R R RR . (9) To acquire a step of 2 dB, S8 and S9 are introduced. If S7 is off and S8 is on in above situation, taking advantage of (8), then out in 1 0 16 0 63 8 dB 2 0 16 0 21 0 63 . . ... | v R R v RRR . (10) -10 dB can obtain by setting S9 on. Table 1 shows the detail control of switches and the corresponding gain. The conventional R-2R topology in [5] has larger output impedance compared to the proposed one when the input is matched. Since larger output impedance introduces more output noise, the proposed one has better noise performance. As the minimum value of resistance is R/8, reducing the parasitic resistance of the switch is critical to ensure the accurate gain. Setting the size of S4, S5 and S6 inverse proportional to their relevant value of resistance can achieve better performance. The switch in [5] is selected for S1, S2, S3, and S7, S8 and S9, they have better linearity performance and good isolation characteristic when they are off. Those switches should also have their ratios. Table 1. Switch control and the corresponding gain S1 S2 S3 S4 S5 S6 S7 S8 S9 S10 Gain (dB) 1 1 1 1 -6 1 1 1 1 -8 1 1 1 1 -10 1 1 1 1 1 -12 1 1 1 1 1 -14 1 1 1 1 1 -16 1 1 1 1 1 1 -18 1 1 1 1 1 1 -20 1 1 1 1 1 1 -22 “1” denotes on, blank denotes off. 2.3 Medium gain path (MGP) ATT LNA for MGP -6 dB, -12 dB, -18 dB 14~20 dB, with 2 dB step vin vout Figure 5. The block diagram of MGP The block diagram of MGP is shown in figure 5. Just three gain modes are used in the attenuator, and the LNA employed here is similar to the LNA used in HGP. As VHF and UHF share the MGP, the bandwidth of MGP is different from the HGP, so the value of the inductor L and the resistance RL. Another difference that should be noted is that the LNA for MGP do not need input matching anymore, which gives more freedom to optimize the noise and linearity performances. So the value of RF is also different. Since 14 dB have two different implementation ways which can be used to choose noise optimization or linearity optimization. For instance, choosing HGP to realize a 14 dB will have a better noise figure than choosing MGP, but the latter have better linearity performance. 8 dB gain and 2 dB gain have similar situations. 3. Measurement results A prototype of this VGLNA which is fabricated in 0.18ȝm CMOS process occupies 870 μm x 760 μm area including pads. Figure 6 shows the die micrograph of the VGLNA and performance summary. Figure 7 shows the 799
measured noise figure at maximum gain,ranging from Figure 9.Measured gain step of attenuator 2.0 dB to 2.4 dB for VHF band and 2.7 dB to 3.5 dB for UHF band.Figure 8 is the measured S11 at different gain, all of them below-9 dB no matter in VHF band or UHF band.Figure 9 depicts the gain step of the proposed attenuator.2 dB gain step is realized well in VHF band While in UHF band,the step is not consistent due to the parasitic effect in high frequencies.Figure 10 displays .40 two tone IIP3 test result at minimum gain,in which two 1+27.9dBm tone input frequencies are set 639.5MHz and 640.5MHz. 60 The measured IIP3 is-7.6 dBm at maximum gain and -80 +27.9 dBm at minimum gain which is just the IIP3 of the -100 attenuator.The IIP3 tests in VHF band have similar -10 0 10 20 30 results. Input Power(dBm） 870m Technobgy 0.18 pm Figure 10.Measured IIP3 minimum gain Die Area 870x760Hm Power 8mA @1.8V 4. Conclusion SII <-9dB This paper demonstrates the design and Gain Range -2220dB implementation of a wideband CMOS VGLNA in 0.18 NF@20 dB 20 dB um CMOS technology.Active AC feedback LNA has IIP3(@-22 dB 27.9 dBm been used in high gain path,which has a good input 50-250MHz Frequency matching performance over a wide frequency range and 470~860MHz a low noise figure.A novel attenuator has been Figure 6.Chip micrograph and performance summary introduced in this paper.Its favorable matching feature, decent gain step coverage and nice linearity have been 3.5 proved in the measurement results.The overall performance of this design is well suited for mobile TV tuner application. 2.5 Acknowledgments The authors would like to thank the staffs in Agilent 0 200 400600 800 1000 Frequency (MHz) Open Lab at Shanghai for chip test and other students Figure 7.Measured noise figure maximum gain from RFIC group at Fudan University for useful test help -5 References -10 [1]Vassiliou I,Vavelidis K,Haralabidis N,et al.A 65 nm CMOS multistandard,multiband TV tuner for mobile and multimedia applications,Solid-State Circuits.IEEE Journal of,p.1522-1533(2008). 1002003004005006007008009001000 [2]Shi Y,Dai FF,Yan J,et al.A fully integrated zero-IF Frequency (MHz) mobile TV tuner RFIC for S-band CMMB application. Figure 8.Measured S11@different gain Custom Integrated Circuits Conference,IEEE,p. 253-256.(2008). [3]Borremans J,Wambacq P.Soens C,et al.Low-area active-feedback low-noise amplifier design in scaled digital CMOS.Solid-State Circuits,IEEE Journal of,p. (p) -10 2422-2433(2008). [4]Razavi B,Design of Analog CMOS Integrated Circuits,p.392(2003). 20 [5]Kefeng H,Xi T,Zhangwen T,et al.A wideband CMOS VGLNA based on single-to-differential stage and resistive attenuator for TV tuners.Journal of -25 100200300400500600700800900 Semiconductors,p.075003(2011). Frequency (MHz) 800
measured noise figure at maximum gain, ranging from 2.0 dB to 2.4 dB for VHF band and 2.7 dB to 3.5 dB for UHF band. Figure 8 is the measured S11 at different gain, all of them below -9 dB no matter in VHF band or UHF band. Figure 9 depicts the gain step of the proposed attenuator. 2 dB gain step is realized well in VHF band. While in UHF band, the step is not consistent due to the parasitic effect in high frequencies. Figure 10 displays two tone IIP3 test result at minimum gain, in which two tone input frequencies are set 639.5MHz and 640.5MHz. The measured IIP3 is -7.6 dBm at maximum gain and +27.9 dBm at minimum gain which is just the IIP3 of the attenuator. The IIP3 tests in VHF band have similar results. Figure 6. Chip micrograph and performance summary 0 200 400 600 800 1000 2 2.5 3 3.5 Frequency (MHz) DSB NF (dB) Figure 7. Measured noise figure @ maximum gain 100 200 300 400 500 600 700 800 9001000 -20 -15 -10 -5 Frequency (MHz) S11 (dB) Figure 8. Measured S11 @ different gain 100 200 300 400 500 600 700 800 900 -25 -20 -15 -10 -5 Frequency (MHz) Attenuation (dB) Figure 9. Measured gain step of attenuator -10 0 10 20 30 -100 -80 -60 -40 -20 0 20 Output Power (dBm) Input Power (dBm) Figure 10. Measured IIP3 @ minimum gain 4. Conclusion This paper demonstrates the design and implementation of a wideband CMOS VGLNA in 0.18 ȝm CMOS technology. Active AC feedback LNA has been used in high gain path, which has a good input matching performance over a wide frequency range and a low noise figure. A novel attenuator has been introduced in this paper. Its favorable matching feature, decent gain step coverage and nice linearity have been proved in the measurement results. The overall performance of this design is well suited for mobile TV tuner application. Acknowledgments The authors would like to thank the staffs in Agilent Open Lab at Shanghai for chip test and other students from RFIC group at Fudan University for useful test help. References [1] Vassiliou I, Vavelidis K, Haralabidis N, et al. A 65 nm CMOS multistandard, multiband TV tuner for mobile and multimedia applications, Solid-State Circuits, IEEE Journal of, p.1522-1533 (2008). [2] Shi Y, Dai F F, Yan J, et al. A fully integrated zero-IF mobile TV tuner RFIC for S-band CMMB application, Custom Integrated Circuits Conference, IEEE, p. 253-256, (2008). [3] Borremans J, Wambacq P, Soens C, et al. Low-area active-feedback low-noise amplifier design in scaled digital CMOS, Solid-State Circuits, IEEE Journal of, p. 2422-2433 (2008). [4] Razavi B, Design of Analog CMOS Integrated Circuits, p.392 (2003). [5] Kefeng H, Xi T, Zhangwen T, et al. A wideband CMOS VGLNA based on single-to-differential stage and resistive attenuator for TV tuners. Journal of Semiconductors, p. 075003 (2011). 800